• Journal of the Korean Society of Laryngology, Phoniatrics and Logopedics
• /
• v.17 no.1
• /
• pp.28-37
• /
• 2006

Purpose: Evaluation of vocal cord vibration is very important in cases of voice disorders. There are several equipments for examining the vocal fold vibration such as laryngeal stroboscope, ultra high-speed digital imaging system, and videokymograph. Among these, laryngeal stroboscope is the most popular equipment because of easy to examine the laryngeal pathology. However, current laryngo-stroboscopes are too bulky to move and relatively expensive. The purpose of this research is to develope a portable laryngeal stroboscope of equivalent performance with the current equipments. Methods and Materials: Recently developed high luminescent white LEDs(light emitting diodes) are placed at the head of the endoscope as light sources for the CCD image sensor which is also placed at the head with imaging lens. This arrangement eliminates the bulky light source like expensive halogen or xenon lamps as well as the optical light guiding cables. The LEDs are controlled to flash in phase with the voice frequency of the examinee. The CCD captures these strobo images and converts them into video signals for examinations. Results: There was no functional differences between preexisting stroboscope and the newly developed stroboscope of this study. LED light sources and microprocessor based control circuits of the stroboscope enabled the development of flicker-less, hand-held, portable and battery-operating stroboscope. Conclusion: The developed stroboscope is cost-effective, small-sized, easy to use and very easy desirable to bring and to use in any place.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.2 no.1
• /
• pp.10-19
• /
• 1992

Mn - Zn Ferrite has physical properties of the high initial permeability, saturation magnetic flux density, and low loss factor as a representative magnetic material of soft ferrites, in addition the mechanical property is excellent as a single crystal. Therefore it is important electronic components and used for VTR Head. Mn - Zn Ferrite single crystals with the diameter 8mm were grown in atmosphere mixed with $O_2$ and Ar gas by the Floating Zone(FZ) method that impurities can not be incorporated to the crystals because of not-using the crucible to put in the melt, and the sharp temperature gradient results from making a focus at one point utilizing the infrared ray emitted from the halogen lamp as a heat source. During the crystal growing, the highest temperature of melting area was maintained to be $1650^{\circ}C$, growth rate and rotation rate were 10 mm/hr, 20 rpm respectively. The phases and the growth directions of crystals were determined from the analysis of X RD patterns, Laue, TEM diffraction patterns and etch pit shapes were observed by the optical microscope through the chemical etching. The corelation of optimum conditions for acquiring the better crystals was found out with the growth rate, the length and diameter of melt at the interface according to the diameter of feed rod, and the patterns of growing interface also studied.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.154-154
• /
• 2006

Samsung Electro Mechanics ink jet has developed ultra high resolution alignment system. The alignment system has been developed for repeatable printing of conductive ink. The resolution of alignment system is 0.5um and the velocity of printing working plate is 1.5m/s. So far repeated printing results included sintering process have over 30um of drop mislocation data. In order to improve line thickness and conductivity of metal line, we need to develop the higher mechanical accurate align system. On the demand, this developed align system has under $1{\sim}2{\mu}m$ mispositioning performance and can measure of mechanical accuracy of inkjet printer, as well as the straightness of jetted drop from inkjet head. There is no kinds limit of substrate and ink to use SEM alignment system. By using this alignment system, we progress two experiment of reiterate printing drop and making conductive line on the glass and photo paper. Optical microscope and 3D profiler has been used for measurement of printed ink.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.4B
• /
• pp.323-332
• /
• 2006

In this paper, we consider a WDM based metro ring connecting broadband access networks by using FT-TR (Fixed Transmitter-Tunable Receiver) type access nodes and a new MAC protocol for fair transmission is proposed. The basic channel access scheme is CSMA/CA(Carrier Sense Multiple Access with Collision Avoidance) and the transferred optical slot is changed to be empty slot by SS(Source-Stripping) which drops a packet from ring-rotated slot. This empty slot can be either used to send head-of-line packet in buffer or transmitted to next access node. In former cases, there is the improvement of network throughput, but latter case leads unfairness problem of transmission. Thus the proposed MAC protocol exploits the advantages form tow cases. It gives downstream access nodes chance to use empty slots and limits the unconditional usage of empty slots at upstream access nodes with probability as called p-Persistent MAC protocol. We use a numerical analysis to evaluate bandwidth efficiency and maximum node throughput and compares simulation results in terms of node throughput, fairness factor, transfer delay depending on probability. Under two different FT-TR type architectures for metro ring network the proposed MAC protocol is evaluated and compared.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.11 no.4
• /
• pp.414-420
• /
• 2018

The digital convergence looking for new ways to engage visitors by superimposing virtual content on projection over the real world captured media contents. This paper propose the Light ID based interactive 3D immersive exhibition things view using HMD AR technology. This approach does not required to add any additional infrastructure to be built-in to enable service and uses the installed Lighting or displays devices in the exhibit area. In this approach, the Light ID can be used as a Location Identifier and communication medium to access the content unlike the QR Tag which supports provide the download information through web interface. This utilize the advantages of camera based optical wireless communication (OWC) to receive the media content on smart device to deliver immersive 3D content visualization using AR. The proposed exhibition method is emulated on GALAXY S8 smart phone and the visual performance is evaluated for Jeonju Hanok Village. The experimental results shows that the proposed method can give immersive 3D view for exhibit things in real-time.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.59-59
• /
• 2009

현재 CMP분야는 광역 평탄화 반도체 소자의 집적화 및 소형화가 진행됨에 따라서 CMP 공정의 중요성은 날로 성장하고 있다. 하지만 이러한 CMP공정은 불가피하게도 scratch, pit, CMP residue와 같은 defect들을 발생시키고 있으며, 점점 선폭이 작아짐에 따라, 이러한 defect들이 반도체 수율에 미치는 영향은 심각해지고 있다. Defect들 중에 특히 scratch는 반도체에 치명적인 circuit failure를 일으키게 된다. 또한 반도체 내구성과 신뢰성을 감소시키게 되고, 누전전류를 증가시키는 등 바람직하지 못한 현상들이 생기게 된다. 본 연구에서는 scratch 와 같은 deflect들을 효율적으로 검출, 분석하고, scratch를 감소시키는데 그 목적이 있다. 본 실험을 위해 8" TEOS wafer와 commercial oxide slurry 및 friction polisher (Poli-500, G&P tech., Korea)를 사용하여 CMP 공정을 진행하였으며, CMP 공정조건은 각각 80rpm/80rpm/1psi(Platen speed/Head speed/Pressure)에서 1분 동안 연마를 한 후 scratch 발생 경향을 살펴보았다. CMP 후 wafer위에 오염되어 있는 slurry residue들을 제거하기 위해 SC-1, HF 세정을 이용하여 최적화된 post-CMP 공정기술을 제안하였다. Scratch 검출 및 분석을 위해 wafer surface analyzer (Surfscan 6200, Tencor, USA)와 optical microscope (LV100D, Nicon, Japan)를 사용하였다. CMP 공정 변수들에 따른 scratch 발생정도를 비교하였으며, scratch 발생 요인들에 따른 scratch 형태 및 발생정도를 살펴보았다. 최적화된 post-CMP 세정 조건은 메가소닉과 함께 SC-1 세정을 실시하여 slurry residue들을 제거한 후, HF 세정을 실시하여 잔여 오염물들을 제거하고 검출이 용이하도록 scratch를 확장시킬 수 있도록 제안하였으며, 100%의 particle removal efficiency (PRE)를 얻을 수 있었다. 실제 CMP 공정후 post-CMP 세정 단계별 scratch 개수를 측정한 결과, SC-1 세정 후 약 220개의 scratch가 검출되었으며, 검출되지 않았던 scratch가 HF 세정 후 확장되어 드러남에 따라 약 500개의 scratch 가 검출되었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.28-28
• /
• 2009

Fabrications of antireflection structures on solar cell were investigated to trap the light and to improve quantum efficiency. Introductions of patterned substrate or textured layer for Si solar cell were performed to prevent reflectance and to increase the path length of incoming light. However, it is difficult to deposit conformally flat electrode on perpendicular plane. ZnO is II-VI compound semiconductor and well-known wide band-gap material. It has similar electrical and optical properties as ITO, but it is nontoxic and stable. In this study, Al-doped ZnO thin films are deposited as transparent electrode by atomic layer deposition method to coat on Si substrate with micro-scale structures. The deposited AZO layer is flatted on horizontal plane as well as perpendicular one with conformal 200 nm thickness. The carrier concentration, mobility and resistivity of deposited AZO thin film on glass substrate were measured $1.4\times10^{20}cm^{-3}$, $93.3cm^2/Vs$, $4.732\times10^{-4}{\Omega}cm$ with high transmittance over 80%. The AZO films were coated with polyimide and performed selective polyimide stripping on head of column by reactive ion etching to measure resistance along columns surface. Current between the micro-columns flows onto the perpendicular plane of deposited AZO film with low resistance.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.4
• /
• pp.84-91
• /
• 2005

We measured the pitch of one-dimensional (ID) grating specimens using a metrological atomic force microscope (M-AFM). The ID grating specimens a.e often used as a magnification standard in nano-metrology, such as scanning probe microscopy (SPM) and scanning electron microscopy (SEM). Thus, we need to certify the pitch of grating specimens fur the meter-traceability in nano-metrology. To this end, an M-AFM was setup at KRISS. The M-AFM consists of a commercial AFM head module, a two-axis flexure hinge type nanoscanner with built-in capacitive sensors, and a two-axis heterodyne interferometer to establish the meter-traceability directly. Two kinds of ID grating specimens, each with the nominal pitch of 288 nm and 700 nm, were measured. The uncertainty in pitch measurement was evaluated according to Guide to the Expression of Uncertainty in Measurement. The pitch was calculated from 9 line scan profiles obtained at different positions with 100 ㎛ scan range. The expanded uncertainties (k = 2) in pitch measurement were 0.10 nm and 0.30 nm for the specimens with the nominal pitch of 288 nm and 700 nm. The measured pitch values were compared with those obtained using an optical diffractometer, and agreed within the range of the expanded uncertainty of pitch measurement. We also discussed the effect of averaging in the measurement of mean pitch using M-AFM and main components of uncertainty.

• Journal of Animal Science and Technology
• /
• v.58 no.12
• /
• pp.42.1-42.8
• /
• 2016

Background: Deficiency of macro and micro-minerals in the ration of dairy cows adversely affects growth, milk production and reproduction efficiency. It is essential to examine mineral concentrations in feeds offered to dairy cows in practical farms. Methods: Two villages from each taluka were selected at random for taking representative samples of feeds, forages and hair. Within the village, help was sought from village milk producers and district animal husbandry officer for identification of 4 to 5 farmers and collection of representative samples. All the samples were processed and analyzed for chemical composition as well as major macro and micro-minerals, using Inductively Coupled Plasma-Optical Emission Spectrometer. Results: Ca content in wheat straw (0.29%), crushed maize (0.02%) and wheat bran (0.12%) was found to be below the critical level (0.30%). The P content in concentrate ingredients was high (0.26-0.96%), but low in dry roughages (0.06-0.12%). Cereal straws (0.14%) and grains (0.12%) were deficient in Mg. Feeds and forages were found to be adequate in K (1.50%). Cereals straws were found to be deficient in S (0.11%). Greens were good source of Cu (12.02 ppm). Wheat straw was found to be low in Zn (18 ppm), but high in Mn (225 ppm) and Fe (509 ppm). Local grasses and azolla green were found to be rich source of Co (>1.00 ppm). Se (0.63 ppm) was present in appreciable quantities in most of the feedstuffs. Conclusions: From the present study, it was apparent that the feeds and forages available in the state of Jharkhand may not meet the requirements for Ca, P, Mg, Cu, Zn and Co in order to sustain a milk production of ~10 kg/day. Therefore, it is necessary to supplement these deficient minerals through area specific mineral mixture in the ration of dairy cows for improving productivity and reproduction efficiency.

• Journal of Chest Surgery
• /
• v.28 no.6
• /
• pp.533-541
• /
• 1995

We recently developed a new model of moving actuator type totally implantable artificial heart[TIAH , based on the reverse position of the aortic and pulmonary conduits. This concept was proposed by one of surgeons in our team[Joon-Ryang Rho, M.D. to facilitate anatomical fitting of TIAHs. The moving actuator type electromechanical TIAH consisted of the left and right blood sacs, and the moving actuator including a motor. The inverted umbrella type polyurethane valves were used in the blood pumps. The aortic conduit was positioned anterior to the pulmonary conduit, which was the opposite relation to the conventional configuration of other total artificial hearts. We also adapted slip-in connectors for the aortic and pulmonary conduits. Two sheep , weighing 60-69 kg, were used for implantation. After small cervical incision and trans-sternal bilateral thoracotomy, cardiopulmonary bypass [CPB was administered using an American Optical 5-head pump and a membrane oxygenator[Univox-IC, Bentley . The anterior and posterior vena cavae were drained separately for venous return. An arterial return cannula was inserted into the right common carotid artery. During CPB, almost all of the ventricular myocardium was excised down to the atrioventricular groove and the artificial heart was implanted. We achieved 3-day survival in the first sheep and 2-day survival in the second. The day after operation the first sheep was successfully extubated and the second sheep was weaned from a respirator with good condition. After extubation, the first sheep walked around in the cage and fed herself. Serial laboratory and hemodynamic examinations were done during the experiments. In both sheep, pulmonary dysfunction was gradually developed, which was accompanied by acute renal failure. The animals were sacrificed and autopsy was done. Unexpected pregnnacy was incidentally found in both sheep. To our knowledge this is the first report of significant survival cases in the orthotopic implantation of electric TIAH using sheep.