• 반도체디스플레이기술학회지
• /
• 제7권1호
• /
• pp.11-16
• /
• 2008

Confocal scanning microscopy is a widely used technique for three dimensional measurements because it is characterized by high resolution, high SNR and depth discrimination. Generally an image is generated by moving one optical probe that satisfies the confocal condition on the specimen. Measurement speed is limited by movement speed of the optical probe; scanning speed. To improve measurement speed we increase the number of optical probes. Specimen region to scan is divided by optical probes. Multi-point information each optical probe points to can be obtained simultaneously. Therefore image acquisition speed is increased in proportion to the number of optical probes. And multiple optical probes from red, green and blue laser sources can be used for color imaging and image quality, i.e., contrast, is improved by adding color information by this way. To conclude, this technique contributes to the improvement of measurement speed and image quality.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1998년도 춘계학술대회 논문집
• /
• pp.95-96
• /
• 1998

An optical modulator with CPW electrode on Ti:LiNbO$_3$ optical waveguide was fabricated and chterized. The electrical-optical bandwidth measurement showed an optical response of -3dB at 10 GHz and S11 less than -l0dB unto 20GHz. The typical specifications are . 5.6V of driving voltage, 4.2dB of Insertion loss and 30dB of on/off extinction.

• 한국생산제조학회지
• /
• 제24권2호
• /
• pp.251-255
• /
• 2015

Thermal deformation, such as bending and twisting, occurs among the polymer parts of air-conditioner indoor units because of repetitive temperature change during heating operation. In this study, a numerical method employing finite-element analysis to efficiently simulate the thermal deformation of an assembly is proposed. Firstly, the displacement of an actual assembly produced by thermal deformation was measured using a 3D optical measurement system. The measurement results indicated a general downward sag of the assembly, and the maximum displacement value was approximately 1 mm. The temperature distribution was measured using a thermographic camera, and the results were used as initial-temperature boundary conditions to perform temperature-displacement analysis. The simulation results agreed well with the measured data. To reduce the thermal deformation, the stiffness increased 100%. As the results, the maximum displacement decreased by approximately 5.4% and the twisting deformation of the holder improved significantly.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2007년도 하계학술발표회 논문집
• /
• pp.61-62
• /
• 2007

• 제어로봇시스템학회논문지
• /
• 제3권6호
• /
• pp.613-618
• /
• 1997

In this paper, we designed a line CCD camera for a flying image, which is composed of a line CCD sensor(2048 cells) and a rotating mirror, and investigated its optical properties. We also made the 3-D image from the flying image which is made of 2-D image being juxtaposed to 1-D images obtained by the camera, and performed the calibration to acquire high precision 3-D data. As a result, we obtained the 3-D measurement system using the slit type of laser projector is available to measure the high precision shape of objects.

• 한국분무공학회지
• /
• 제7권3호
• /
• pp.31-37
• /
• 2002

In previous study, diesel-methanol stratified injection system is manufactured and applied to a D.I. diesel engine in order to realize combustion improvement using methanol, which is oxygenated fuel with large latent heat. We know that NOx and soot is reduced by stratified injection of diesel fuel-methanol. Therefore, in the present study, combustion diagnosis using optical measurement is tried to make clear effect of methanol on simultaneous reduction of NOx and soot. Two-color method is used to measure flame temperature and KL value, which is approximately proportional to the soot consentration along the optical path. Laser induced scattering method was used to measure distribution of soot at two dimensional area. Also, it is compared exhaust characteristics of NOx and soot with results of optical measurement.

• 전자공학회논문지D
• /
• 제35D권6호
• /
• pp.72-78
• /
• 1998

Ti:LiNbO$_3$ 광도파로위에 CPW 전극 구조를한 광변조기 내부칩을 제작한 후 일련공정에 따라 패키징 작업을 하였고 소자의 전기적특성과 광학적특성을 측정하였다. 광변조기 패키징을 위하여 페룰, 보조용 LN블럭 및 글래스, 진동 및 흡수용패드, 알루미나피더의 부분품을 사용하였으며 피그테일링, Au 와이어본딩, 에폭싱, SMA커넥팅, 실링 작업을 수행하였다. 전기적 특성에서 S/sub 21/은 -3 dB 점에서 9.8GHz의 값을, S/sub 11/은 14.4 GHz 대에서 -8.9 dB 값을 나타내었다. 광학적 특성은 제작된 광도파로가 1550nm 파장대에서 단일모드를 만족하였고, 패키지후 소자의 삽입손실은 실온에서 4.3 dB 이였으며, 소자를 온도감압챔버에 넣은후 5∼45℃까지 온도변화를 주었을 때 4.3∼6.4 dB의 삽입손실을 보였다. E-O bandwidth 응답은 3dB점에서 7.8GHz를 나타내어 10Gbps급 광통신시스템에 응용할수 있음을 확인하였다.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2009년도 창립 20주년기념 특별학술발표회
• /
• pp.42-43
• /
• 2009

• International Journal of Control, Automation, and Systems
• /
• 제3권1호
• /
• pp.130-136
• /
• 2005

A new optical digitizing system for determining the position of a cursor in three dimensions(3D) and an experimental device for its measurement are presented. A semi-passive system using light intensity modulation, a technology that is well known in radar ranging, is employed in order to overcome precision limitations imposed by background light. This system consists of a charge-coupled device camera placed before a rotating mirror and a light-emitting diode whose intensity is modulated. Using a Fresnel pattern for light modulation, it is verified that a substantial improvement of the signal to noise ratio is realized for the background noise and that a resolution of less than a single pixel can be achieved. This opens the doorway to the realization of high precision 3D digitized measurement. We further propose that a 3D position measurement with a monocular optical system can be realized by a numerical experiment if a linear-period modulated waveform is adopted as the light-modulating one.

• 제어로봇시스템학회논문지
• /
• 제22권3호
• /
• pp.186-191
• /
• 2016

This paper addresses the development of 3D data acquisition system (3D scanner) based laser structured-light image. The 3D scanner consists of a stripe laser generator, a conventional camera, and a rotation table. The stripe laser onto an object has distortion according to 3D shape of an object. By analyzing the distortion of the laser stripe in a camera image, the scanner obtains a group of 3D point data of the object. A simple semiconductor stripe laser diode is adopted instead of an expensive LCD projector for complex structured-light pattern. The camera has an optical filter to remove illumination noise and improve the performance of the distance measurement. Experimental results show the 3D data acquisition performance of the scanner with less than 0.2mm measurement error in 2 minutes. It is possible to reconstruct a 3D shape of an object and to reproduce the object by a commercially available 3D printer.