• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 춘계학술발표대회 논문집
• /
• pp.31-34
• /
• 2002

A study on the method that can measure the internal strain of composite materials is performed to monitor the health status of composite structures. A fiber optic sensor was constructed using the total reflected extrinsic Fabry-Perot interferometer(TR-EFPI) probe with a broadband light source. Result obtained from electrical strain gage adhered on the aluminum beam specimen was compared with that from the fiber optic TR-EFPI sensor and showed a good agreement. It was found that fiber optic TR-EFPI sensor system was adequate for monitoring the strain and thus failure processes in the interior of composite materials.

• 정보통신설비학회논문지
• /
• 제4권1호
• /
• pp.7-13
• /
• 2005

In this paper, we propose the time synchronization module on fiber optic repeater to use optic line delay for obtaining time synchronization between up-link and down-link, in the 2.3 GHz WiBro network using TDD/OFDM (Time Division Duplex/Orthogonal Frequency Division Multiplexing) Generally, when we use fiber optic repeater to remove the shade area, it occurs transmission delay which is caused by optic transmission between RAS (Radio Access Station) and fiber optic repeater and inner delay of fiber optic repeater. Because the WiBro system is adopting a TOO method and there exists the difference of switching time which is caused by these delay between up-link and down-link, it occurs ISI (Inter Symbol Interference), ICI (Inter Carrier Interference). These interference results in the reduction of the coverage. And the inconsistency between Up-Link and Down-Link switching time maybe gives rise to the interruption of communication. In order to prevent these cases, we propose synchronization module using analog optic line delay as the one of synchronizing up-link and down-link. And we propose the consideration factor for the designing time synchronization module and the feature of optic line of analog method. The measurement result of optic line time synchronization module of structure proposed is as follows, the delay error of $0.5{\mu}g$ and the insertion loss value below maximum 4.5dB in range of $0{\sim}40{\mu}s$. These results fully meet the specification of WiBro System.

• 한국음향학회지
• /
• 제22권7호
• /
• pp.585-591
• /
• 2003

본 연구에서는 소형화 및 경량화의 특성을 가진 Fabry-Perot형 간섭계를 구성하였다. 음향이 광섬유의 횡방향으로 감지되도록 센서 헤드부를 1㎝정도로 제작하고 총 길이가 9.5㎝인 광섬유의 양단을 단순 지지토록 하였다. 센서의 음향 감지특성을 관찰하기 위하여 무지향성 스피커를 이용하여 음향신호를 인가하였다 횡방향으로 입력된 음향 신호를 광섬유 센서와 마이크로폰이 감지한 신호를 비교하였다. 1㎑ 이하의 신호에서는 광섬유 센서가 마이크로폰보다 감지 특성이 좋으나 2 ㎑에서는 광섬유센서의 감지 특성이 감소하였다. 이것은 제작된 광섬유 센서의 지지구조의 특성을 나타낸 것이며 실험을 통하여 Fabry-Perot 간섭계용 센서는 횡방향의 음향을 잘 감지함을 확인하였다. 이러한 형태의 센서는 지능구조물의 건강진단 모니터링 분야에도 적용가능 하리라 판단된다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 추계학술대회 논문집 학회본부
• /
• pp.508-510
• /
• 1995

A fiber-optic pressure sensor is fabricated with a photoelastic glass material. To remove the influence of external pertubation along the optical fiber, a new referencing technique is proposed by using two light sources. LED with 870nm wavelength is used as light source for reference signal, and LED with 660nm wavelength is used as light source for modulation signal. The fiber-optic pressure sensor system shows good linearity within the pressure range of 0 to 5 $kg/cm^2$.

• 소음진동
• /
• 제9권6호
• /
• pp.1152-1156
• /
• 1999

In this study, a fiber optic air-backed mandrel hydrophone has been constructed and performance of acoustic signal detection has been measured. The hydrophone is based on a Mach-Zehnder interferometer with 35 m of sensing fiber. The sensitivity is measured up to -128 dB re rad/$\mu$ Pa in range from 1.4 kHz to5 kHz. A system with this design of hydrophone may be applied to detect low frequency underwater acoustic signals.

• 조명전기설비학회논문지
• /
• 제29권8호
• /
• pp.76-82
• /
• 2015

A hybrid fiber-optic sensor system which combines fiber Bragg grating sensors and a Michelson interferometer has been constructed and evaluated for condition monitoring of large scale wind turbines. In order to measure multiple stresses applied to wind turbines such as strain, temperature and vibration, the system uses single broadband light source. It addresses both types of sensors, which simplifies the optical setup and enhances the cost-effectiveness of condition monitoring system. An athermal-packaged FBG is used to supply quasi-coherent light, of which coherence length is about 3.28mm, for the Michelson interferometer demodulation. Experimental results demonstrated that the proposed fiber-optic sensor system was capable of measuring strain and temperature with measurement accuracy of 1pm. Also 500~2000Hz vibration signals were successfully analyzed by applying FFT signal processing to interference signals.

• Journal of Biosystems Engineering
• /
• 제31권2호
• /
• pp.128-134
• /
• 2006

Frequent outbreaks of foodborne illness demand the need for rapid and sensitive methods for detection of these pathogens. Recent development of biosensor technology has a great potential to meet the need for rapid and sensitive pathogens detection from foods. An antibody-based fiber-optic biosensor and an automated reagents supply system to detect Listeria monocytogenes were developed. The biosensor for detection of Listeria monocytogenes in PBS and bacteria spiked food samples was evaluated. The automated reagents supply system eliminated cumbersome sample and detection antibody injection procedures that had been done manually. The biosensor could detect $10^4$ cfu/ml of Listeria monocytogenes in PBS. By using the fiber-optic biosensor, $2x10^8$ cfu/ml of Listeria monocytogenes in the food samples were detectable.

• 공학논문집
• /
• 제2권1호
• /
• pp.103-111
• /
• 1997

EDFA는 광전송시스템에서 광섬유상에 전파되는 신호가 광섬유의 손실로 인해 약해지게 되는데 미약해진 신호의 광세기를 키워주는 증폭기로서 널리 사용되고 있다. EDFA의 증폭기작을 주요 인자를 가지고 분석함으로써 그 특성을 이해하고 이를 토대로 EDFA 설계시 유용한 기준으로 삼고자 한다. 또한 광전송시스템에서의 EDFA는 자연방출광잡음으로 인해 수신단에서 신호대잡음비를 악화시켜 전송오율을 증가시키게 되는데 이를 억제하기 위한 동작조건 즉 잡음지수의 최소화하는 동작조건에 대해서 논하고자 한다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제11권3호
• /
• pp.221-228
• /
• 2011

This paper describes 250-Mb/s fiber optic transmitter and receiver ICs for plastic optical fiber applications using a$ 0.18-{\mu}m$ CMOS technology. Simple signal and light detection schemes are introduced for power reduction in sleep mode. The transmitter converts non-return-to-zero digital data into 650-nm visible-red light signal and the receiver recovers the digital data from the incident light signal through up to 50-m plastic optical fiber. The transmitter and receiver ICs occupy only 0.62 $mm^2$ of area including electrostatic discharge protection diodes and bonding pads. The transmitter IC consumes 23 mA with 20 mA of LED driving currents, and the receiver IC consumes 16 mA with 4 mA of output driving currents at 250 Mb/s of data rate from a 3.3-V supply in active mode. In sleep mode, the transmitter and receiver ICs consume only 25 ${\mu}A$ and 40 ${\mu}A$, respectively.

• 비파괴검사학회지
• /
• 제27권4호
• /
• pp.291-298
• /
• 2007

본 논문은 단자유도 동적 센서 시스템의 동적 구간을 조절할 수 있는 새로운 신호 처리법을 소개한다. 또한 본 논문에서는 무아래 현상을 응용한 신개념의 광섬유 가속도계를 사용하여 신호 처리법을 검증하였다. 신개념의 광섬유 가속도계는 단일 질량, 단일 탄성자 그리고 단일 감쇠자로 이루어진 단자유도 동적 시스템으로서 동적 구간이 작아 이출 증가시키기 위해서는 질량이나 탄성자 상수를 조절하는 등의 기계적 조절이 필요하다. 그러나 본 논문에서 제안한 신호처리 방법을 적용한다면 센서를 다시 제작하지 않고도 동적 구간을 쉽게 조절할 수 있게 된다. 본 논문에서는 여러 모의실험과 실제 실험을 통해 본 신호 처리 알고리즘의 성능을 검증하였으며 결과적으로 이러한 신호처리 알고리즘이 광섬유 가속도계의 동적 구간을 손쉽게 조절할 수 있는 효과적인 방법임을 보여주었다.