• 한국항공우주학회지
• /
• 제41권7호
• /
• pp.588-595
• /
• 2013

항공탑재 SAR 시스템은 유/무인 항공기에 탑재되어 고해상 영상정보 수집과 지상 이동 표적 탐지의 임무를 담당하는 영상 레이더 시스템으로, 선진국을 중심으로 운용되고 있으며 국내에서도 현재 개발이 진행 중에 있다. 본 논문에서는 항공탑재 SAR 시스템 운용을 위한 운용요구조건 및 운용 요구조건을 만족하기 위한 다중모드 및 실시간 SAR 시스템 운용개념에 대하여 기술한다. 항공 시스템과의 연동개념, 시스템 상태정의 및 천이개념, 임무정의파일 기반 임무수행 개념, 고장진단 및 관리개념, 촬영자료 저장 및 전송 개념에 대해 설명하고, 지상검증시험을 통한 SAR 시스템 운용개념 검증 결과에 대해 기술한다.

• 정보통신설비학회논문지
• /
• 제9권4호
• /
• pp.124-130
• /
• 2010

This paper considers a power saving technique of set-top box (STB) that turns the signal into content which is then displayed on the television (TV) screen. A traditional power saving scheme, Auto Power Down (APD), was devised to reduce the power consumption of STB. APD checks whether the user is watching TV over a period of time and enforces STB into stand-by mode when the check result reveals the user is not watching TV. This paper proposes an enhanced power saving scheme that transits STB operation mode to 'stand-by' immediately when STB recognizes the change of TV's external input signal. The proposed scheme does not require the monitoring time to check the users' watching TV, and transits to standby mode faster than the conventional APD, which results in better performance in power saving. The simulation result shows that the proposed scheme achieves 2 to 11% improvement in power consumption compared with the conventional APD.

• Journal of electromagnetic engineering and science
• /
• 제9권3호
• /
• pp.146-151
• /
• 2009

This paper presents a low-loss broadband balun that uses a coplanar waveguide-to-slotline field transformation. It operates over a very wide frequency range and is of compact size since it does not depend on a resonant structure. To analyse imbalance, the coplanar wavelength(CPW) input ground is connected to the CPW output ground through various capacitors to introduce common-mode impedances. As the common-mode impedance increased the imbalance became significantly higher at the higher-frequency band compared with the lower-frequency band. The bias-circuit approach is used to improve the operation bandwidth of the lower-frequency band. The measured results show a passband of 200 MHz to 2 GHz, an insertion loss of less than 0.75 dB, and a size of $20{\times}14\;mm$. The amplitude imbalance is approximately 0.3 dB and the phase imbalance is less than $6^{\circ}$ over the entire operational range.

• 시스템엔지니어링학술지
• /
• 제1권2호
• /
• pp.43-48
• /
• 2005

This paper describes the results of applying States and Modes Analysis, one of the requirements analysis techniques, to the development requirements of flight control software for Smart UAV. State/mode table enabled us to investigate various operation and design concepts, and as a result essential requirements for flight control software were established without omitting necessary requirements. Through the use of scenario-specific state transition diagrams, dynamic behaviours and control/response interfaces between each state and mode could been clearly identified, which made it possible to establish requirements related to dynamic behaviours of states and modes which are essential to the design of flight control software.

• Journal of Power Electronics
• /
• 제15권4호
• /
• pp.1035-1046
• /
• 2015

This study presents a practical implementation of a multi-mode two-phase interleaved boost converter for fuel cell electric vehicle application. The main operating modes, which include two continuous conducting modes and four discontinuous conducting modes, are discussed. The boundaries and transitions among these modes are analyzed with consideration of the inductor parasitic resistance. The safe operational area is analyzed through a comparison of the different operating modes. The output voltage and power characteristics with open-loop or closed-loop operation are also discussed. Key performance parameters, including the DC voltage gain, input ripple current, output ripple voltage, and switch stresses, are presented and supported by simulation and experimental results.

• 전기학회논문지
• /
• 제65권9호
• /
• pp.1597-1604
• /
• 2016

The speed at which the SRM (Switched Reluctance Motor) makes a transition from chopping control to single pulse operation. (i.e., low speed to high speed operation). It is unsatisfied with performance at all operational regimes. In this paper, the operational performance of SRM can be improved by using current hysteresis control method. This method maintains a generally flat current waveform. At the high speed, the current chopping capability is lost due to the development of the back-EMF. Therefore SRM operates in single pulse mode. By using zero-current switching and zero-voltage switching technique, the stress of power switches can be reduce in chopping mode. When the commutation from one phase winding to another phase winding, the current can be zero as fast as possible in this period because several times negative voltage of DC-source voltage produce in phase winding. This paper is compared to performance based on energy efficient C-dump converter topology and the proposed resonant C-dump converter topology. Simulation and experimental results are presented to verify the effectiveness of the proposed circuit.

• 전기학회논문지P
• /
• 제57권2호
• /
• pp.72-78
• /
• 2008

The speed variation of SRM is fulfilled throughout a transition from chopping control to single pulse operation. (i,e., low speed to high speed operation). It is unsatisfied with performance at all operational regimes. In this paper, the operational performance of SRM can be improved by using current hysteresis control method. This method maintains a generally flat current waveform. At the high speed, the current chopping capability is lost due to the development of the back-EMF. Therefore SRM operates in single pulse mode. By using zero-current switching and zero-voltage switching technique, the stress of power switches can be reduce in chopping mode. When the commutation from one phase winding to another phase winding, the current can be zero as fast as possible in this period because several times negative voltage of DC-source voltage produce in phase winding. This paper is compared to performance based on conventional C-dump converter topology and the proposed resonant C-dump converter topology. Simulation and experimental results are presented to verify the effectiveness of the proposed circuit.

• 전력전자학회논문지
• /
• 제18권5호
• /
• pp.448-457
• /
• 2013

This paper proposes a control method under stand-alone operating mode for distributed-module type photovoltaic power conditioners. In conventional schemes, there are some problems of a controller saturation in the DC-link (or load) voltage controller when overly-heavy load, light load, and the generated PV power reduction occurs, as well as when a transition occurs from an overly-loaded to normal conditions. To overcome these problems, the proposed controller method switches the main control target from DC-link voltage to the maximum power point, which is closer to the stable operating point when it returns to normal operating conditions. For the analysis, a state-plane trajectory was given and the circuit analysis by PSIM simulation was done. For the verification, a prototype hardware with 110[W] and 50[W] dual photovoltaic modules has been implemented. From the results, it can be seen that PV power tracking is successfully done with the proposed method even under a stand-alone operation mode.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1998년도 추계학술대회 논문집
• /
• pp.210-218
• /
• 1998

The ATO(Automatic Train Operation) System is used for train operation instead of drivers. It is interfaced with TCMS(Train Control and Monitoring System) and ATC/TWC system in the train and wayside facilities. In this paper describes configuration of ATO, specification of ATO hardware, construction of ATO software and the algorithm fur automatic train speed regulation in the carborn ATO system. ATO Application Software is consist of ART, SPR, REG, SRV and PSM tasks. ART task is main control part of the ATO that determine ATO control, ATO mode, state transition. SPR determine speed reference according to train motion status, track data, train data and restricted train speed. REG task regulated train speed form the starting of one station to the precision stop at the other station under the result of ART and SPR tasks. In this paper, a algorithm for the train speed regulation while running is described.

• Journal of Power Electronics
• /
• 제19권1호
• /
• pp.11-23
• /
• 2019

In this study, a novel zero voltage zero current transition (ZVZCT) bidirectional DC-DC converter is proposed by employing coupled inductors. This converter can turn the main switch on at ZVZCT and it can turn it off with zero voltage switching (ZVS) for both the boost and buck modes. These characteristics are obtained by using a simple auxiliary sub-circuit regardless of the power flow direction. In the boost mode, the auxiliary switch achieves zero current switching (ZCS) turn-on and ZVS turn off. Due to the coupling inductors, this converter can make further efficiency improvements because the resonant energy in the capacitor or inductor can be transferred to the load. The main diode operates with ZVT turn-on and ZCS turn-off in the boost mode. For the buck mode, there is a releasing circuit to conduct the currents generated by the magnetic flux leakage to the output. The auxiliary switch turns on with ZCS and it turns off with ZVT. The main diode also turns on with ZVT and turns off with ZCS. The design method and operation principles of the converter are discussed. A 500 W experimental prototype has been built and verified by experimental results.