• Journal of the Institute of Electronics and Information Engineers
• /
• v.49 no.9
• /
• pp.251-258
• /
• 2012

Recently, NAND Flash memory structure is evolving from SDR (Single Data Rate) to high speed DDR(Double Data Rate) to fulfill the high performance requirement of SSD and SSS. Accordingly, the proper ways of transferring data that latches valid data stably and minimizing data skew between pins by using PHY(Physical layer) circuit techniques have became new issues. Also, rapid growth of speed in NAND flash increases the operating frequency and power consumption of NAND flash controller. Internal voltage variation margin of NAND flash controller will be narrowed through the smaller geometry and lower internal operating voltage below 1.5V. Therefore, the increase of power budge deviation limits the normal operation range of internal circuit. Affection of OCV(On Chip Variation) deteriorates the voltage variation problem and thus causes internal logic errors. In this case, it is too hard to debug, because it is not functional faults. In this paper, we propose new architecture that maintains the valid timing window in cost effective way under sudden power fluctuation cases. Simulation results show that the proposed technique minimizes the data skew by 379% with reduced area by 20% compared to using PHY circuits.

• Journal of Periodontal and Implant Science
• /
• v.29 no.3
• /
• pp.469-484
• /
• 1999

The purpose of this study was to evaluate new bone formation following guided bone regeneration by resorbable and nonresorbable membrane. Six adult mongrel dogs were used. The first, second, third, fourth premolars in the mandible of each dog were extracted. Two months after tooth extraction, a buccal dehiscence defect was surgically created on each edentulous area. The experimental sites were divided into three groups according to the treatment modalities ; Group I-a: surgical treatment only ; Group I -b: allogenic decalcified freezed dried bone grafting ; Group II-a : e- PTFE membrane placement only ; Group II-b : allogenic decalcified freezed dried bone grafting and e-PTFE membrane placement ; Group III-a : Vicryl(R) mesh placement only ; Group III-b : allogenic decalcified freezed dried bone grafting and Vicryl(R) mesh placement . The animals were sacrificed at 8 weeks after operation and the specimens were prepared for histologic and histometric examination. The results were as follows : Clinically, all defect sites were healed without exposure of barrier membrane after the eight weeks. In Group I-a, dense connective tissues were impinged in the bony defect area. Well vascularized and fibrous bone marrow indicated that bone formation was still taking place was found. In Group I-b, in areas closer to the periphery, lamellation of the newly formed bone would found. In Group II-a, beneath the e-PTFE membrane a dense layer of connective tissue covering the most external portions of the regenerated tissue was seen. The new bone surfaces were lined with osteoid and osteoblast. In Group II-b, a dense layer of connective tissue covering the most external portions of the regenerated tissue was observed beneath the e-PTFE membrane. A notable amount of alveolar ridge regeneration was seen with new rigdes with well-contoured form. In Group III-a, the new bone surface were lined with osteoid and osteoblast, indicating active bone formation. A clear demarcation could not be noted between the host bone and new bone. In Group III-b, a notable amount of alveolar ridge regeneration was seen with new ridges assuming wellcontoured form. In areas closer to the periphery, lamellation of the newly formed bone would found. As histometric examination, the amount of bone formation was gained from $12.8mm^2$ to $26.3mm^2$. It was significantly greater in group II-b and group III-b compared to other groups(p<0.05) . These results suggest that Vicryl(R) mesh after DFDB grafting used in guided bone regeneration could create and sustain sufficient space for new bone formation.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.12 no.6
• /
• pp.304-310
• /
• 2002

Novel charge trap type memory devices with reoxidized oxynitride gate dielectrics made by NO annealing and reoxidation process of initial oxide on substrate have been fabricated using 0.35 $\mu \textrm{m}$ retrograde twin well CMOS process. The feasibility for application as NVSM memory device and characteristics of traps have been investigated. For the fabrication of gate dielectric, initial oxide layer was grown by wet oxidation at $800^{\circ}C$ and it was reoxidized by wet oxidation at $800^{\circ}C$ after NO annealing to form the nitride layer for charge trap region for 30 minutes at $850^{\circ}C$. The programming conditions are possible in 11 V, 500 $\mu \textrm{s}$ for program and -13 V, 1ms for erase operation. The maximum memory window is 2.28 V. The retention is over 20 years in program state and about 28 hours in erase state, and the endurance is over $3 \times 10^3$P/E cycles. The lateral distributions of interface trap density and memory trap density have been determined by the single junction charge pumping technique. The maximum interface trap density and memory trap density are $4.5 \times 10^{10} \textrm{cm}^2$ and $3.7\times 10^{18}/\textrm{cm}^3$ respectively. After $10^3$ P/E cycles, interlace trap density increases to $2.3\times 10^{12} \textrm{cm}^2$ but memory charges decreases.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.22 no.3
• /
• pp.8-16
• /
• 1986

The fishing conditions of flying squid, ommastrePhes barsram(Lesueur), in the North Pacific Ocean was studied based on the horizontal water temperature data, satellite data from NOAA and statistical data of flying squid fisheries which were collected from 1980 to 1984. The obtained results were as follows; 1. Since 1979, the Korean drift giIlnet fishery for flying squid was launched in North Pacific. Number of operating vessel and catch of flying squid increased gradually every year. The number of vessels were 111 and their annual catches were 42, 977 M/T in 1984. Therefore, Korean drift giIlnet fishery for this species has played an important role in the products of Korean high-sea fisheries. 2. In the beginning of the fisheries, fishing grounds was formed in the west of long. 1800E. In 1982, in consequence of the center which extended eastward, the fishing ground was formed long. 166$^{\circ}$W in the central North Pacific Ocean. Since 1983, the fishing grounds were formed as far as long. 161$^{\circ}$W. The range of general fishing season in the central North Pacific was from June to August. After september, fishing ground was shifted to the west, in the Northwestern Pacific. 3. The Predominant fishing season for the flying squid was August through January of the coming year. Optimum water temperature for flying sguid at surface layer in the Pacific Ocean ranged from 11 $^{\circ}$e to 17$^{\circ}$e in winter, 13$^{\circ}$e to 17$^{\circ}$e in spring, 12. 8$^{\circ}$C to 19.7$^{\circ}$e in summer and 1O.6$^{\circ}$e -18.7$^{\circ}$e in fall. 4. In summer, the Oceanographic condition in the North Pacific Ocean showed that the water temperature at surface layer was lower in 1980, 1983 and higher in 1981, 1982 and 1984 as compared with mean annual water temperature. 5. The characteristics df oceanographic conditions in the fluation, disformation, mixing and other factors of the Kuroshio and Oyashio currents, which have considerably influenced upon the water masses of the areas. 6. The data and information on surface thermal Structure interpreted from Infrared Satellite Imaginary from NOAA-7 and NOAA-8 are very available in estimating water temperature on the areas and investigating the major fishing grounds. 7. According to the fisheries statics of Japanese drift gilInet, the annual catches of flying squid considerably decreased from 225, 942 M/T in 1983 to 133, 217 M/T in 1984. 8. The fishing grounds in the central North Pacific in several fishing seasons were formed as follows: In June, the initial fishing season, the fishing grounds were formed in the vicinity of lat. 35 - 40oN, the central North Pacific east of 179$^{\circ}$E. In July, the fishing ground were formed in the wide arEa of the central North Pacific north of 400N and long. 174$^{\circ}$E-145$^{\circ}$W In Auguest, concentrative fishing operation carried out in :he central North Pacific north of 43$^{\circ}$N and East of 165$^{\circ}$W. On the other hand, in September, main fishing grounds were disappeared and moved to the west.

• The KIPS Transactions:PartA
• /
• v.12A no.3 s.93
• /
• pp.205-214
• /
• 2005

Flash memory is at high speed used as storage of personal information utilities, ubiquitous computing environments, mobile phones, electronic goods, etc. This is because flash memory has the characteristics of low electronic power, non-volatile storage, high performance, physical stability, portability, and so on. However, differently from hard disks, it has a weak point that overwrites on already written block of flash memory is impossible to be done. In order to make an overwrite possible, an erase operation on the written block should be performed before the overwrite, which lowers the performance of flash memory highly. In order to solve this problem the flash memory controller maintains a system software module called the flash translation layer(FTL). Of many proposed FTL schemes, the log block buffer scheme is best known so far. This scheme uses a small number of log blocks of flash memory as a write buffer, which reduces the number of erase operations by overwrites, leading to good performance. However, this scheme shows a weakness of low page usability of log blocks. In this paper, we propose an enhanced log block buffer scheme, FAST(Full Associative Sector Translation), which improves the page usability of each log block by fully associating sectors to be written by overwrites to the entire log blocks. We also show that our FAST scheme outperforms the log block buffer scheme.

• Korean Journal of Remote Sensing
• /
• v.34 no.3
• /
• pp.481-494
• /
• 2018

The accurate radiative transfer model simulation is essential for an accurate ozone profile retrieval using optimal estimation from backscattered ultraviolet (BUV) measurement. The input parameters of the radiative transfer model are the main factors that determine the model accuracy. In particular, meteorological parameters such as temperature and surface pressure have a direct effect on simulating radiation spectrum as a component for calculating ozone absorption cross section and Rayleigh scattering. Hence, a sensitivity of UV ozone profile retrievals to these parameters has been investigated using radiative transfer model. The surface pressure shows an average error within 100 hPa in the daily / monthly climatological data based on the numerical weather prediction model, and the calculated ozone retrieval error is less than 0.2 DU for each layer. On the other hand, the temperature shows an error of 1-7K depending on the observation station and altitude for the same daily / monthly climatological data, and the calculated ozone retrieval error is about 4 DU for each layer. These results can help to understand the obtained vertical ozone information from satellite. In addition, they are expected to be used effectively in selecting the meteorological input data and establishing the system design direction in the process of applying the algorithm to satellite operation.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2003.07a
• /
• pp.309-316
• /
• 2003

Generally, sesame are dried on the field after being harvested in Korea. Since harvesting season is rainy autumn and sesame drying is mainly affected sun and natural wind, it is difficult to dry sesame in time. Moreover, sesame threshing by hand is very laborious work. Therefore, tractor mounted sesame thresher which threshes sesame bundles fed in upside down and conveyed along threshing bar was developed to mechanize sesame threshing and to reduce labor cost in this research. the thresher was equipped with a threshing bar which beats sesame bundles and a three layer sieve which screens sesame. The results are summarized as follows ; 1 The sesame thresher was consisted of a hitting-stick, a feeding chain conveyor, a threshing bar, conveyor belt, and the three-layer shaking sieve. 2. In threshing test, prototype thresher showed maximum threshing ratio 98.5%, 98.7% at 14, 17 cpm beating rate respectively. 3. In screening test, prototype sieve showed maximum threshing ratio 97.2% at 12$^{\circ}$ of inclined angle and 220 cpm of sieve vibrating rate. 4. Prototype showed 98.7% of threshing ratio, 1.3% of threshing loss, 97.0% of screening ratio, 0.7% of screening loss on the rest condition of 15 sesame bundles/min of feeding rate, 14 cpm of beating rate, 220 cpm of sieve vibrating rate. 5. The working performance of prototype was 0.5hr/10a. It was 9.6 times more efficient than manual work. And, operation cost of prototype was saved by 45.9% compared to manual work.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.35 no.1
• /
• pp.1-10
• /
• 1999

The north-west sea area of Cheju Island is where originate two layer current in the summer season. The case of the fishing operations in this sea area is almost impossible for normal expansion of the net gear for shooting net, and is happened to be frequent occasions for rise of tension suddenly in purseline by changes of the net shapes in the operation. Therefore, the safety of the operations is often obstructed by the above mentioned. In connection with the above, model experiments on the purse seine in the circulating water tank was carried out in comparison and analysis on the changes of tension in the pruseline by deformation of purse seine in the sea area of two layer current. THe results obtained are as follows;In the case of the required time for pursing of 20 minutes in the no current set, the increasing curve for tension of purseline can be expressed as:Y=0.0004x3+0.0098x2+0.3000x(r=0.9989)where Y is tension(metric tons) of a purseline, x is required time(minutes) for pursing. And, the maximum value of tension in this time was an increase of 31.3 percent at 15 minutes, and was a decrease of 30.3 percent at 30 minutes than that of 20 minutes.When the bottom margin of net is held on the position in velocity of 0.5 knot at three-eighths of net in the bottom current to the net height, the maximum tension of the required time for pursing of 30 minutes in tight set and loose set were decrease of 29.5 percent and 28.7 percent respectively than that of 20 minutes.The work load during the required time for pursing of 20 minutes were calculated 5.79×106 kgf·m in no current set, 7.89×106 kgf·m in tight set and 5.15×106 kgf·m in loose set, therefore it was an increase of 22.3 percent in tight set, and was a decrease of 11.1 percent in loose set than that of the no current set. Where tight set and loose set is a range of the bottom current with velocity of 0.5 knot at three-eighths of net to the net height.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.9 s.351
• /
• pp.6-13
• /
• 2006

In this paper, we studied vehicle to vehicle (VTV) communication system using DSRC of 5.8 GHz bands. Nowadays, in the road traffic system is going intelligent and advancing, communication between driving vehicle is very important technology for ITS. We can contrive smoothness and safety traffic flowing by exchanging information about velocity, location, braking and driving condition of nearby vehicles. Therefore, we developed and verified the system which required for the communication among vehicles using DSRC technology of 5.8 GHz band hasa 1 Mbps data rate in the high mobility condition. For this, we developed DSRC modem, data link layer and logic link layer to make it possible that communication between vehicles of perfectly operation, and developed application service program for VTV communication. We performed to communication test in the general road and ascent road. In case of the general mad, obtained VTV communication results are more than number of 17 with in 300 m LOS coverage, and total communication time are $2.34{\sim]18.7$ msec that considered maximum 8-transaction. We blow that obtained results can be used VTV communication or the in areas form the feasibility road test as a function or various conditions. In the future, this system is very useful of advanced safety vehicle (ASV) and super smart vehicle system (SSVS) and so on.

• Journal of the Korean Electrochemical Society
• /
• v.2 no.3
• /
• pp.150-155
• /
• 1999

The Electrochemical stabilities of the Brewer-Engel type intermetallic compounds of Co-Mo $(35 wt\%)$ and Ni-Mo$(35 wt\%)$ manufactured by the arc-melting method for the hydrogen electrode of $H_2-O_2$ alkaline fuel cell were investigated. Effects of temperature and concentration on the electrochemical behavior of the electrodes in the $80^{\circ}C$ 6 N KOH solution deaerated with $N_2$ gas were studied by electrochemical methods. The effect of overpotential on the electrochemical stabilities of Co-Mo and Ni-Mo intermetallic compounds was also discussed under the normal operation condition of AFC. It was shown that Co-Mo electrode had lower electrochemical stability as compared to Ni-Mo. In the case of Co-Mo electrode, a simultaneous dissolution of cobalt and molybdenum has occurred at low anodic overpotential form equilibrium hydrogen electrode potential, but the dissolution of cobalt was serious, and Co(OH)l layer on the electrode surface formed at the high anodic overpotential. In contrast the Ni-Mo electrode had high electrochemical stability because formation of the dense and thin protective $Ni(OH)_2$ layer prevented the dissolution of molybdenum.