• Proceedings of the Acoustical Society of Korea Conference
• /
• spring
• /
• pp.381-384
• /
• 2002

이종 매질에서 초음파전달은 각 매질의 음향임피던스에 영향을 받는다. 초음파진동자로 사용되는 압전소자와 매질로 가장 많이 사용되는 물은 음향임피던스 차이가 크므로 경계면에서 투과율이 감소한다. 이를 개선하기 위해 압전소자와 물 사이에 음향정합층을 삽입하여 사용한다. 정합층은 1 layer로 사용되는 경우도 있지만, 넓은 대역폭을 요구하는 분야에서는 2 layer가 사용된다. 본 논문에서는 1 layer 정합층를 갖는 초음파 트랜스듀서에 대해 시간영역에서 해석하는 기법을 분석하였으며, 이를 근거로 매질 사이의 물리적 특성을 고려하여 2 layer 정합층을 갖는 초음파트랜스듀서를 해석하였다. 해석결과 2 layer 정합층일 경우 1 layer에 비해 공진주파수에서의 이득은 감소하였으나 대역폭이 증가됨을 알 수 있었다.

• Proceedings of the Optical Society of Korea Conference
• /
• 1989.02a
• /
• pp.169-171
• /
• 1989

The curved active layer inner stripe(CALIS) laser diode has been developed. The tight confinements of current and carrier result in low thershold current(20-30mA) with stable fundamental transverse mode operation up to the output power of 30mW CW.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.3
• /
• pp.621-627
• /
• 2010

This paper proposes an efficient architecture of Inter layer up-sampling in decoder for SVC(scalable video coding). A register bank for horizontal and vertical up-sampling and interpolation units are designed, by introducing the proposed architecture, 41% memory bandwidth is reduced compared to JSVM. For real-time operation for HD 6 layer decoder having CIF, SD, HD resolution for CGS layer, the hardware is designed to operate at 127MHz. The gate count is about 3000.

• Proceedings of the Korean Information Science Society Conference
• /
• 2002.10d
• /
• pp.415-417
• /
• 2002

날로 커져가는 3D 모델을 효율적으로 사용하기 위한 노력으로 압축처리 방법들이 연구되고 있다. 본 논문에서는 3D 모델의 메쉬를 Layer로 분할하여 Vertex Layer와 Triangle Layer를 생성 후, 삼각형들을 몇가지 연산코드로 분류하여 압축(compression)하는 방법을 제안한다. Triangle Layer는 기본 정점으로부터 연결된 선분의 정점들로 이루어진 Vertex Layer의 쌍을 이용하여 만들어진다. 이 Triangle Layer에 해당 되는 삼각형들의 연결 정보를 제안한 연산코드로 분류하고, 이것을 엔트로피 코딩하여 3D 모델을 압축한다. 이 기법은 삼각형의 형태를 기준으로 한 개나 두 개의 삼각형을 하나의 연산코드로 분류하거나 삼각형의 연결 상황에 따라 하나의 연산코드로 분류하여 연결정보를 표현한다. 복원(decompression)시에는 연산 코드를 이용하여 삼각형의 연결정보를 뽑아내면 원 상태의 3D 모델을 획득할 수 있다. 이 방법은 연결 정보를 무손실 압축하는 방법으로, 지금까지 제안된 압축기법과 비교할 때, 간단하면서도 월등한 압축 효과를 볼 수 있다.

• Bulletin of the Korean Chemical Society
• /
• v.24 no.4
• /
• pp.437-440
• /
• 2003

In a mediator-aided microbial fuel cell, the choice of a proper mediator is one of the most important factors for the development of a better fuel cell system as it transfers electrons from bacteria to the electrode. The electrochemical behaviors within the lipid layer of two representative mediators, thionin and safranine O both of which exhibit reversible electron transfer reactions, were compared with the fuel cell efficiency. Thionin was found to be much more effective than safranine O though it has lower negative formal potential. Cyclic voltammetric and fluorescence spectroscopic analyses indicated that both mediators easily penetrated the lipid layer to pick up the electrons produced inside bacteria. While thionin could pass through the lipid layer, the gradual accumulation of safranine O was observed within the layer. This restricted dynamic behavior of safranine O led to the poor fuel cell operation despite its good negative formal potential.

• 제어로봇시스템학회:학술대회논문집
• /
• 1990.10b
• /
• pp.1184-1189
• /
• 1990

In order to investigate liquid fuel filming over the intake manifold wall, an electrode-type probe has been developed by lines of authors and this probe was employed in a single cylinder two and four-stroke cycle engine and in a four cylinder four-stroke engine operated by neat methanol fuel. The performance of the probe was dependent upon several parameters including the liquid fuel layer thickness, temperature, additive in the fuel, and electric power source (i.e., AC and voltage level) and was independent of other variables such as direction of liquid flow with respect to the probe arrangement. Several new findings from this study may be in order. The flow velocity of the fuel layer in the intake manifold of engine was about (if the air velocity in the steady state operation, the layer thickness of liquid fuel varied in both the circumferential and longitydinal directions. In the transient operation of the engine, the temporal variation of fuel thickness was determined, which clearly suggests that there was difference between fuel/air ratio in the intake manifold and that in the cylinder. The variation was greatly affected by the engine speed, fuel/air ratio and throttle opening. And the variation was also very significant from cylinder to cylinder and it was particularly strong different engine speeds and throttle opening.

• 정보저장시스템학회:학술대회논문집
• /
• 2005.10a
• /
• pp.185-189
• /
• 2005

We reported here nano-scale electrical phase-change recording in amorphous $Ge_2Sb_2Te_5$ media using an atomic force microscope (AFM) having conducting probes. In recording process, a pulse voltage is applied to the conductive probe that touches the media surface to change locally the electrical resistivity of a film. However, in contact operation, tip/media wear and contamination could major obstacles, which degraded SNR, reproducibility, and lifetime. In order to overcome tip/media wear and contamination in contact mode operation, we adopted the W incorporated diamond-like carbon (W-DLC) films as a protective layer. Optimized mutilayer media were prepared by a hybrid deposition system of PECVD and RF magnetron sputtering. When suitable electrical pulses were applied to media through the conducting probe, it was observed that data bits as small as 25 nm in diameter have been written and read with good reproducibility, which corresponds to a data density of $1 Tbit/inch^2$. We concluded that stable electrical phase-change recording was possible mainly due to W-DLC layer, which played a role not only capping layer but also resistive layer.

• Journal of the Korean Society for Precision Engineering
• /
• v.5 no.1
• /
• pp.29-39
• /
• 1988

Plastically deformed layer beneath metal surface machined by orthogonal cutting was evaluated in terms of residual stress, microvickers hardness, side spread, and the side strain. An attempt was made to predict the depth of layer according to machining conditions particularly tool geometry and the shear plane angle. In this paper, we employed two models concerning the sliplines. The exact model was validated by comparision of computed and measured tool force and its angle, and the model offers an upper boundary of the deformed layer to be in good agreement with the experiment.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 1997.11a
• /
• pp.625-632
• /
• 1997

A two-dimensional zone-like model is developed to predict the interaction between hot gas layer and water droplets after sprinkler activation. The model combines the motion equations for each droplet with heat and mass transfer between the gas and water. The results indicate that negative buoyancy in the hot layer can only be obtained if the initial temperature profile is uniform. If an experimental profile Is used instead, positive buoyancy results. This conclusion has been confirmed with experimental data.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.12
• /
• pp.99-106
• /
• 2010

Gas turbines operation for power generation increased rapidly since 1990 due to the high efficiency in combined cycle, relatively low construction cost and low emission. But the operation and maintenance cost for gas turbine is high because the expensive superalloy hot gas path parts should be repaired and replaced periodically This study analyzed the initiation and propagation of the crack at the gas turbine blades which are coated with MCrAIY as a bond coat and TBC as a top coat. The sample blades had been serviced at the actual gas turbines for power generation. Total 7 sets of blades were analyzed and they have different EOH(equivalent operation hour). Blades were sectioned and the cracking distribution were measured and analyzed utilizing SEM(scanning electron microscope) and optical microscope. The blades which had 52,000 EOH of operation had cracks at the substrate and the maximum depth was 0.2 mm. Most of the cracks initiated at the boundary layer between TBC and bond coat and propagated down to the bond coat. Once bond coat is cracked, the base metal is exposed to the oxidation condition and undergoes notch effect. Under this environment, the crack branched at the inter-diffusion layer and propagated to the substrate. Critical cracks affecting the blade life were analyzed as those on suction side and platform.