• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.5 no.3
• /
• pp.21-29
• /
• 1985

An effective technique of sludge separation is required for concentrated activated sludge process. The dissolved-air flotation (DAF) has been shown to be efficient process for sludge separation. The factors affecting DAF process for activated sludge separation are type and concentration of sludge, air/solid ratio, ratio of pressurized water flow, pressure, sludge detention time, temperature, sludge and hydraulic loading rate, recycle flow rate of sludge and type and quantity of chemical aid. In order to study the optimal operation condition for sludge separation, the influence factors such as type and concentration of sludge, ratio of pressurized water flow and pressure are investigated by the batch and continuous reactor experiments of DAF and sedimentation test. By the experimental investigation, the results are as follows; 1. For the bulking and concentrated sludge, DAF is more effective than sedimentation for the sludge separation. 2. In DAF, the critical ratio of pressurized water flow exist. The critical value varies with the pressure in the tank. That is, according to the pressure changes from 3 to $5kg/cm^2$, the critical value varies from 0.25 to 0.67 accordingly. 3. Pressure affects the ratio of pressurized water flow, but it does not show any influence upon the DAF efficiency directly. 4. Continuous experimental results was not better than those of batch.

• Journal of Korean Society of Environmental Engineers
• /
• v.37 no.4
• /
• pp.204-209
• /
• 2015

The effluent limit of nickel from electroplating wastewater has been strengthened from 5 mg/L to 3 mg/L from 2014. However, currently applied treatment process for nickel plating wastewater is unable to meet the effluent limit, most of the treatment concept conducted by treatment plant is dilution with other metal bearing wastewater. This can cause very significant impact to the environment of nickel contamination. With this connection, the feasibility test has been conducted with the use of electrolysis by using sacrificial electrodes. Experiments were conducted in synthetic and electroless nickel plating wastewater. Optimal condition of current density, pH were derived from the synthetic wastewater. It was found that the removal efficiency of nickel exceeded 94% at the operation condition of at pH 9 and the current density of $1{\sim}2mA/cm^2$. At this conditions, the iron sludge was generated very low amount. However, it was unsuccessful to meet the effluent limit by applying these treatment conditions to the real electroplating wastewater. This can be explained due to the matrix effect of other metals and anions contained real electroplating wastewater. From the result of further study, the optimal conditions for the real wastewater treatment were found out to be at pH 9, current density $6{\sim}7mA/cm^2$, for 5 minutes of operating time. At these conditions, 88% removal of nickel was achieved, which results the residual nickel concentration was below 3 mg/L.

• Journal of Astronomy and Space Sciences
• /
• v.21 no.2
• /
• pp.141-152
• /
• 2004

Optics fabrication process for precision space optical parts includes bound abrasive grinding, loose abrasive lapping and polishing. The traditional bound abrasive grinding with bronze bond cupped diamond wheel leaves the machine marks of about $20{mu}m$ rms in height and the subsurface damage of about 1 ${mu}m$ rms in height to be removed by subsequent loose abrasive lapping. We explored an efficient quantitative control of precision CNC grinding. The machining parameters such as grain size, work-piece rotation speed and feed rate were altered while grinding the work-piece surfaces of 20-100 mm in diameter. The input grinding variables and the resulting surface quality data were used to build grinding prediction models using empirical and multi-variable regression analysis. The effectiveness of such grinding prediction models was then examined by running a series of precision CNC grinding operation with a set of controlled input variables and predicted output surface quality indicators. The experiment achieved the predictability down to ${pm}20$ nm in height and the surface roughness down to 36 nm in height. This study contributed to improvement of the process efficiency reaching directly the polishing and figuring process without the need for the loose abrasive lapping stage.

• International Journal of Highway Engineering
• /
• v.14 no.3
• /
• pp.151-162
• /
• 2012

It is not surprising to hear news about irresistible natural disasters all over the world due to climate change. Korean Government has focused on developing a variety of green technologies to reduce green house gasses, in particular, carbon dioxide. This study suggested 18 technology divisions for achieving green highway technology development in six different sub-sectors considering life-cycle of roadway and surveyed 29 highway and/or transportation professionals of three institutes using AHP(Analytical Hierarchy Process) analysis to construct "Green Highway"and realize carbon emission reductions and energy use efficiency in a road sector in Korea. Expert Choice Software was used to rank 18 technology divisions weighted by two-level choices. Transport Operating Infrastructure Improvement, Roadway Policy Implementation, Green Transportation(such as Pedestrian and Bicycle) were highly ranked by respondents according to results of the AHP modeling. Among the 18 divisions, technology policy for supporting R&D investments from development to commercialization was ranked as the most significant one to be focused. Green Transportation Facility Design/Construction/Operation and Eco-Friendly Roadway Plan were followed as expected since professionals have thought that the planning/design step of the life-cycle is a starting point to reduce carbon dioxide from roads more and more. Additionally, comparing the results with the Government investment trend 2006-2011 for the roads, it can be interpreted that the Government should invest to the R&D area more widely than before to promote element and core technology development for Green Highway Construction. Above all, small and mid-sized businesses have to be invested as well as encouraged to undertake green highwayrelated objects to accomplish the divisions which ranked high.

• Science of Emotion and Sensibility
• /
• v.10 no.4
• /
• pp.583-601
• /
• 2007

The desktop interface is not suitable for the environment in which mobile devices are used commonly with moving, because much attention should be paid for it. And the miniaturizing of mobile devices increases the workload for using them, makes the operation speeds lower and makes more errors. So the study of appropriate level of the input interface for this changing environment is needed. In the aspect of mobile devices. input style and the complexity of the menu hierarchy, this study will look for the way to decrease the workload when doing some primary tasks and using mobile devices simultaneously with moving. The input style was classified into gesture input style, button input style, and pointing input style. The accuracy and speed were measured when doing dual tasks, including a menu searching task and a figure memory task, through one input style of three. By Changing the level of menu hierarchy in the menu searching task, the accuracy of task execution was examined. These Experiments were done in standing state and moving state. In both state the pointing input style was the highest in the accuracy of task execution but the slowest in the speed. In contrast, the gesture input style was not high in the accuracy but the fastest in the speed. This fact shows that the gesture input style is suitable for the condition needed for speedy processing rather than accurate execution when moving.

• Journal of Korean Society of Transportation
• /
• v.35 no.1
• /
• pp.63-78
• /
• 2017

The purpose of this study is to determine the optimal aggregation interval to increase the reliability when estimating representative value of individual vehicle travel time collected by DSRC equipment in interrupted traffic flow section in National Highway. For this, we use the bimodal asymmetric distribution data, which is the distribution of the most representative individual vehicle travel time collected in the interrupted traffic flow section, and estimate the MSE(Mean Square Error) according to the variation of the aggregation interval of individual vehicle travel time, and determine the optimal aggregation interval. The estimation equation for the MSE estimation utilizes the maximum estimation error equation of t-distribution that can be used in asymmetric distribution. For the analysis of optimal aggregation interval size, the aggregation interval size of individual vehicle travel time was only 3 minutes or more apart from the aggregation interval size of 1-2 minutes in which the collection of data was normally lost due to the signal stop in the interrupted traffic flow section. The aggregation interval that causes the missing part in the data collection causes another error in the missing data correction process and is excluded. As a result, the optimal aggregation interval for the minimum MSE was 3~5 minutes. Considering both the efficiency of the system operation and the improvement of the reliability of calculation of the travel time, it is effective to operate the basic aggregation interval as 5 minutes as usual and to reduce the aggregation interval to 3 minutes in case of congestion.

• International Journal of Highway Engineering
• /
• v.11 no.3
• /
• pp.121-128
• /
• 2009

This study has proposed the signal operating system to use both semi-actuated signal control and pedestrian push-button as a way to make up for the problems of 3 leg intersections which are operated inefficiently in the signal operation, one of the methods of traffic operations. In case of the semi-actuated signal control, it can reduce delay inside the intersection by serving to uncongested traffic on the main road where there is not much traffic volume on the secondary road and push-button signal can reduce unnecessary waiting time it could happen to vehicles by operating it though there is no pedestrian. Quantitative analysis was tried regarding the average delay reduction per vehicle using VISSIM, microscopic simulation program regarding how much effect it has compared with the existing signal control system and semi-actuated signal control system when the above two advantages are collected. The field test was performed for one three-leg intersection of Incheon. According to respectively signal control method pedestrian traffic changed and executed a sensitivity analysis. The result which compares the average delay time per a vehicle of scenarios, the signal control method of using the pedestrian push-button system in comparison with the fixed signal control method showed to decrease effect of a minimum 3.7 second (10%), a maximum 5.8 second (16%). When the pedestrian traffic volume was 20% or less of the measurement traffic volume, The signal control method of using the pedestrian push-button system appeared to be more efficient the semi-actuated signal control with object intersection.

• Journal of Korean Society of Transportation
• /
• v.21 no.1
• /
• pp.7-19
• /
• 2003

The airspace has to be designed considering the flight safety and economic efficiency of aircraft operators. The International Civil Aviation Organization(ICAO) published standards and recommended practices for safe design of the airspace. Each contracting country must follow the ICAO standards in designing the airspace for the utilization of civil aviation. Normally each member establishes its own standards and national aviation law for the safe and efficient design of the airspace, regarding the ICAO standards. However, our government has not developed yet clear and detailed standards and regulation system for airspace design. This might lead to aviation accidents and disputes between operators of aviation system This study is to review the characteristics of ICAO standards and a legal problem related to application of international standards for airspace design. Specifically this research analyzed the case of airspace design and operation of a domestic airport. The results of analysis are as follow: (1) per the safety of civil aviation, it is very required to establish national regulation system to follow ICAO standards in designing airspace, (2) It is also necessary to establish separate procedure for civil aircraft in military air base, when the aerodrome is co-used by military and civil aircraft. If the same procedure for military aircraft is applied to civil aircraft, it is necessary to make clear what the design concept is, (3) and the differences from ICAO standards have to be publicly known.

• Journal of Korean Society of Transportation
• /
• v.36 no.2
• /
• pp.67-85
• /
• 2018

Vehicle platooning through wireless communication and automated driving technology has become realized. Platooning is a technique in which several vehicles travel at regular intervals while maintaining a minimum safety distance. Truck platooning is of keen interest because it contributes to preventing truck crashes and reducing vehicle emissions, in addition to the increase in truck flow capacity. However, it should be noted that interactions between vehicle platoons and adjacent manually-driven vehicles (MV) significantly give an impact on the performance of traffic flow. In particular, when vehicles entering from on-ramp attempt to merge into the mainstream of freeway, proper interactions by adjusting platoon size and inter-platoon spacing are required to maximize traffic performance. This study developed a methodology for establishing operational strategies for truck platoonings on freeway on-ramp areas. Average speed and conflict rate were used as measure of effectiveness (MOE) to evaluate operational efficiency and safety. Microscopic traffic simulation experiments using VISSIM were conducted to evaluate the effectiveness of various platooning scenarios. A decision making process for selecting better platoon operations to satisfy operations and safety requirements was proposed. It was revealed that a platoon operating scenario with 50m inter-platoon spacing and the platoon consisting of 6 vehicles outperformed other scenarios. The proposed methodology would effectively support the realization of novel traffic management concepts in the era of automated driving environments.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.1373-1377
• /
• 2007

준설은 수중굴착, 운반(배송), 매립 기술로 구분되는데, 국내에서는 아직까지 각 기술을 통합한 체계적인 연구가 수행되지 못하고 있다. 준설분야는 토질, 수리 등의 토목 분야 기술뿐만 아니라 기계, 제어, 환경 등 여러 분야의 기술들이 매우 복잡하게 연계되어 있으며, 제한된 소수의 기술자들과 특수 대형 장비-준설선에 의해 수행되기 때문이다. 최근에는 장비의 대형화, 첨단화가 진행되면서 선진국과의 기술격차로 인해 국제 경쟁력이 약화되어 심각한 위기에 처해있는 현장기술 분야이다. 유럽의 델프트 공대, IHC, 준설협회(CEDA)는 세계 기술 개발을 주도하고 있으며, 미국에서는 육군공병단의 수로국에서 준설을 담당하고 있으며 DOER(Dredging Operation & Environmental Research) 기술 개발을 주도하는 등 선진국에서는 이미 여러 연구가 진행되었으며 준설기술이 정착되어있다. 본 연구에서는 현재 현대건설에서 보유중인 아산3호를 모델로 축소모형을 제작하여 실험하였다. 본 연구에서는 선행실험으로 성층형성 및 석션펌프 작동시 물입자의 운동방향을 PIV로 촬영한 결과에 커터헤드를 추가 장착 시행하여 이를 바탕으로 수치해석시 발생할 수 있는 오류를 수정 보완 할 것이다. 차후 실험에서는 준설토의 조건과 기계적 조건 및 환경적인 영향력을 고려한 여러 가지 방법으로 진행할 계획이며, 실험 조건에서는 각 매개변수를 달리하여 이를 토대로 데이터를 구성하고, 측정을 통해서 얻어지는 결과 값을 기초로 하여 준설시에 환경과 매개변수의 조건에 따른 준설량의 특성을 파악하고 효율을 향상시킬 수 있는 방향을 제시할 것이며, 이를 통해서 기본적인 메뉴얼을 구성할 계획이다. 수리실험의 결과값을 바탕으로 이를 현실무 작업에 적용할 경우 효율적인 준설작업을 수행할 수 있을 것으로 판단된다. HDL-콜레스테롤 함량은 유의차가 없었다. 간조직 중 총지질, 총콜레스테롤 및 중성 지방 함량은 HC군이 NC군에 비하여 유의하게 증가되었다. HC-LREL 군과 HC-LREH군은 HC군에 비하여 간조직 중 총지질 함량만이 유의하게 저하되었다. 이상의 결과 연근 에탄올 추출물은 in vitro에서 HMG-CoA reductase 활성을 농도 의존적으로 저하시켰으며, in vivo 에서는 고콜레스테롤 식이급여로 증가되어진 LDL-콜레스테롤 및 중성지질 함량을 감소시키고, 감소되어진 인지질 함량을 증가시킴으로써 고콜레스테롤 혈증 및 지방간의 예방과 치료에 효과가 있을 것으로 사료되나 연근의 어떠한 성분의 작용 기전에 의한 것인지에 대해서는 더욱 체계적인 연구가 요구된다.}nlein$ nephritis가 3례로 가장 많았다. 미세변화 신증후군 71명 중 비재발군이 16명으로 22.5%, 비빈발 재발군 49.3%, 빈발 재발군 18.3%, 스테로이드 의존군 9.9%를 보였다. 결론 : 대전시에서의 신증후군 환아의 발생빈도는 15세이하 소아 10만명당 약 5명으로 추정되었으며 10여 년전과 비교하여 큰 변화를 보이지는 않았다. 또한 저자들의 임상병리학적 연구결과가 다른 문헌에서 보고된 소아 신증후군의 연구결과와 큰 차이를 보이지 않음을 알 수 있었다. 자극에 차이가 있지 않나 추측되며 이에 관한 추후 연구가 요망된다. 총대장통과시간의 단축은 결장 분절 모두에서 줄어들어 나타났으나 좌측결장 통과시간의 감소 및 이로 인한 이 부위의 통과시간 비율의 저하가 가장 주요하였다. 이러한 결과는 차가운 생수 섭취가 주로 결장 근위부를 자극하는 효과를 발휘하는 것이 아닌가 해석된다. 이와 같은 연구결과를 통해 생다시마를 주원료로 개발된 생다시마차와 생다시마 음료가 만성 기능성 변비 증세를 개선하는 효