• Journal of Korean Society of Industrial and Systems Engineering
• /
• 제36권3호
• /
• pp.17-24
• /
• 2013

Release planning in a software product line (SPL) is to select and assign the features of the multiple software products in the SPL in sequence of releases along a specified planning horizon satisfying the numerous constraints regarding technical precedence, conflicting priorities for features, and available resources. A greedy genetic algorithm is designed to solve the problems of release planning in SPL which is formulated as a precedence-constrained multiple 0-1 knapsack problem. To be guaranteed to obtain feasible solutions after the crossover and mutation operation, a greedy-like heuristic is developed as a repair operator and reflected into the genetic algorithm. The performance of the proposed solution methodology in this research is tested using a fractional factorial experimental design as well as compared with the performance of a genetic algorithm developed for the software release planning. The comparison shows that the solution approach proposed in this research yields better result than the genetic algorithm.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• 제60권7호
• /
• pp.1331-1338
• /
• 2011

This paper proposes a method for frequency control of islanded microgrid with battery energy storage system. For frequency control of islanded microgrid, battery energy storage system uses a phase locked loop algorithm with positive sequence components for a fast frequency estimation. Microgrid is a power system with small inertia because it has small capacity generators and inverter systems for renewable energy. So, Islanded microgrid's frequency varies fast and large as small generation and load changes. To reduce frequency variation of islanded microgrid, it needs a device with fast frequency response. For fast frequency response, a fast frequency tracking is important. To show the validation of proposed fast frequency tracking algorithm, battery energy storage system with proposed algorithm is tested in microgrid pilot plant.

• Proceedings of the KIPE Conference
• /
• 전력전자학회 2017년도 전력전자학술대회
• /
• pp.221-222
• /
• 2017

본 논문에서는 위치 센서에 의존하지 않는 매입형 영구자석 전동기의 센서리스 구동 시 전압 왜곡으로 인해 나타나는 위치 추정 오차를 이론적으로 분석하고자 한다. 특히, 추정 d축에 맥동하는 구형파 전압을 주입하는 방법에서 주입하는 신호의 주파수에 따라 위치 추정 성능이 달라지는 현상에 초점을 맞춘다. 무부하에서 스위칭 주파수의 신호를 주입할 때 전압 왜곡은 on/off sequence에서 서로 반대의 위상을 갖는 역상분 2고조파의 형태로 나타나며, 위치 추정 오차는 3고조파의 형태로 나타난다. 반면, 반스위칭 주파수의 신호를 주입하는 경우에는 샘플링 주기 동안 주입 전압 왜곡의 효과가 상쇄되기 때문에 인덕턴스의 영향만이 주로 고려되어 위치 추정 오차가 6고조파의 형태로 나타난다. 시뮬레이션과 실험을 통해 이론적 분석의 타당성을 검증하였다.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2003년도 추계학술대회 논문집 전력기술부문
• /
• pp.266-268
• /
• 2003

This paper proposes the Fault Location Estimation Algorithm in the parallel transmission lines. These algorithm uses a variable data window method based on least square error method to estimate fault impedance quickly. And it selects the optimal equation according to the operation situation and usable fault data for minimizing the fault estimation error effected by the zero sequence mutual coupling. After simulation result, we can see that these algorithm estimates fault location more rapidly and exactly.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 2003년도 하계학술대회 논문집 D
• /
• pp.2483-2485
• /
• 2003

As design a network system that should command and response to do tasks by PLC, to make factory automation for being distributed facilities which are not guaranteed procedure, through polling method, commands are send orderly by PLC and responses are answered by each sub-unit. It make a guarantee of sequence and drive a master-slave operation in network. This method help to distribute procedure systems and make possible dividing tasks to each unit. To make this method, network protocol's format have Master or Slave ID and tasking data and Master's command or Slave unit's report. In network interpret algorithm, skip algorithm are included and it make guarantee of protecting data though network are in noise. Data that are made by this method are send to PC to transmit long-distance user by internet.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• 제22권4호
• /
• pp.93-98
• /
• 2014

In this study, control of oxidizer mass flow rate and verification of control system were performed for hybrid rocket thrust control application. Oxidizer flow control system consists of ball valve and stepping motor where gaseous oxygen was used for oxidizer at feeding pressure of 10, 20 and 30 bar. According to experimental results, the oxidizer mass flow rate showed a relatively linear increment as ball valve open angle increases regardless of feeding pressure. In addition, the level of the oxidizer flow rate was kept almost constant at each sequence of flow control with ball valve during the 20 seconds of operation.

• Transactions of the Korean Society of Automotive Engineers
• /
• 제12권1호
• /
• pp.184-189
• /
• 2004

In this paper, the warm forging process sequence has been determined to manufacture the warm forged product for the precision bevel gear used as the differential gear unit of a commercial automobile. The preform shape of bevel gear influences the dimensional accuracy and stiffness of final product. The aspect ratio and chamfer length are considered as design parameters to achieve adequate metal distribution in the finish forging operation. Then the optimal conditions of design parameters have been selected by artificial neural network (ANN). Finally, to verify the optimal preform shape, the experiments of the warm forging of the bevel gear have been executed. The proposed method can give more systematic and economically feasible means for designing the preform shape in metal forming process.

• IE interfaces
• /
• 제11권2호
• /
• pp.199-209
• /
• 1998

In manufacturing industries, one of the critical issues is to synchronize the sequence of production operations with materials needed at each operation to improve productivity. In order to solve this synchronization problem. We develop a code system entitled 'Work-Order-Number' for automated storage/retrieval systems(AS/RS) in this paper. The Work-Order-Number is designed for the purpose of integrating the engineering information. material handling, production and operations scheduling, point of production, and AS/RS systems. This paper implemented the Work-Order-Number in the electric motor manufacturing. The results of the implementation showed the reduction of the number of workers in material handling and cost-loss due lo a late delivery.

• Journal of Korean Institute of Industrial Engineers
• /
• 제25권4호
• /
• pp.466-475
• /
• 1999

A backward Dynamic Programming(DP) model for the optimal facility replacement decision problem during a finite planning horizon is presented. Multiple alternative challengers to a current defender are considered. All facilities are assumed to have finite service lives. The objective of the DP model is to maximize the profit over a finite planning horizon. As for the cost elements, purchasing cost, maintenance costs and repair costs as well as salvage value are considered. The time to failure is assumed to follow a weibull distribution and the maximum likelihood estimation of Weibull parameters is used to evaluate the expected cost of repair. To evaluate the revenue, the rate of operation during a specified period is employed. The cash flow component of each challenger can vary independently according to the time of occurrence and the item can be extended easily. The effects of inflation and the time value of money are considered. The algorithm is illustrated with a numerical example. A MATLAB implementation of the model is used to identify the optimal sequence and timing of the replacement.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 한국펄프종이공학회 2004년도 추계학술발표집
• /
• pp.221-232
• /
• 2004

Paper process is complex and multivariable system. Identification of a paper process model is imperative for the development of predictive control method. 13-level Pseudo-Random Sequence Signals were used to identify the plant model in which the neural network model was considered model as a real paper process. Results of simulations for identification using 13-level PRS signals and Prediction Error Method are compared with plant operation data. From the comparison, we can see that the dynamics of the model show good agreement with those of real plant.