• Journal of Power System Engineering
• /
• v.14 no.5
• /
• pp.76-82
• /
• 2010

This paper investigates the optimum operating conditions to construct total automatic control system with high energy efficiency of a newly developed seawater ice machine. The machine has an electronic expansion valve(EEV) and a variable speed rotating drum with an evaporator installed inside. The coefficient of performance(COP) was used as an index to evaluate energy efficiency of the machine. At first, the opening angle of EEV was adjusted to obtain COP of the machine at a constant speed of the drum. Then, we checked seawater ice product versus opening angles of the EEV. Finally, effect of drum's rotating speed in response to product of seawater ice and seawater ice temperature were considered.

• Structural Engineering and Mechanics
• /
• v.26 no.3
• /
• pp.231-250
• /
• 2007

The influence of masonry infills with eccentric openings on the seismic performance of reinforced concrete (r/c) frames that were designed in accordance with current code provisions are investigated. Eight 1/3-scale, single-story, single-bay frame specimens were tested under cyclic horizontal loading up to a drift level of 4%. In all examined cases the shear strength of columns was higher than the cracking shear strength of solid infill. The parameters investigated include the shape and the location of the opening. Assessment of the behavior of the frames is also attempted, based on the observed failure modes, strength, stiffness, ductility, energy dissipation capacity and degradation from cycling loading. Based on these results there can be deduced that masonry infills with eccentrically located openings has been proven to be beneficial to the seismic capacity of the bare r/c frames in terms of strength, stiffness, ductility and energy dissipation. The location of the opening must be as near to the edge of the infill as possible in order to provide an improvement in the performance of the infilled frame.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.5
• /
• pp.719-725
• /
• 2014

Transient of Electric railway vehicle occurs when change to another state. The duration of the transient phenomenon only takes a few second. During this time is considered, the present of short circuit current and the normal state, the energy is present in the form of a magnetic field. Recognized by the vibration of the transient voltage or transient current at witch energy is present in the field. This paper is presented the result of transient characteristics by transformer % impedance at the time of opening and closing of the main circuit Breaker on the electric railway vehicle.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.6
• /
• pp.1-7
• /
• 2011

Sound waves and acoustic energy generated by two identical TA (ThermoAcoustic) lasers were analyzed and studied. One end of the ceramic stack was heated by a thin NiCr wire wound around that end. The other end of the stack was cooled by natural convection of atmospheric air. The wavelength of the sound waves generated by a single TA laser was four times the tube length and the amplitude of the waves increased with the heating rate. SPL (SoundPressure Level) meters and microphones were employed to measure and study the sound waves at different distances from the glass tube opening and at the focusing point of the TA laser pair for different laser position arrangements. The sound waves of the two TA lasers at the focusing point were found to be almost 180 degrees out of phase when the openings of the two lasers were very close to each other and the angle between the laser axes was small. When the two TA lasers were placed far apart, the sound wave amplitudes and the phase difference between the two laser outputs varied periodically with time. The frequencies of the sound waves changed when the openings of the two TA lasers were in close vicinity and the angle between the laser axes exceeded a certain value. In this case, the glass tube opening was no longer a pressure anti-node and the wavelength of the fundamental mode was not equal to four times the tube length.

• Journal of Hydrogen and New Energy
• /
• v.28 no.1
• /
• pp.106-112
• /
• 2017

The present study describes flow induced noise generated from a ball valve used for a gas pipeline. Noise generation from a ball valve mainly induces by interference between unstable(or fluctuating) leakage flow and pipe wall when the ball valve is working closed or opened. To measure the positions of the noise source and the amplitude of noise with respect to measuring frequencies, a commercial acoustic camera is introduced. Noise characteristics generated by the ball valve have been performed by four valve opening rates: 30, 50, 70 and 100 percents. It is noted that 100 percent opening rate means that the valve is fully opened. Throughout the experimental measurements using the acoustic camera, the location of the noise source and the noise amplitude with respect to the frequencies for the test ball valve are clearly evaluated. It is found that the dominant frequencies come from the fluctuating flow at the downstream of the ball valve for four opening rates are observed between 3,000Hz and 3,200Hz. Maximum noise amplitude comes from the ball valve reaches 75dB at the valve opening rate of 50 percent.

• Tunnel and Underground Space
• /
• v.28 no.5
• /
• pp.457-475
• /
• 2018

For increase of reality in numerical analysis, a blasting vibration waveform obtained from field blast operations has been directly used for input parameters of dynamic analysis in the form of vibration velocity. A numerical model was built considering the geological characteristics of underground limestone opening as well as the mining stages in this opening, and the effect of blast operations on stability of underground limestone opening was investigated by dynamic numerical analysis. The adequacy of applying the real vibration waveform to dynamic analysis has been approved from the preliminary analysis, and the dynamic numerical analysis results show that the continuous mining operation can cause the collapse of roof in openings and the active yield zone around openings. Therefore, the additional reinforcements should be applied for ensuring the stability of underground limestone openings.

• Polymer(Korea)
• /
• v.33 no.5
• /
• pp.458-462
• /
• 2009

We have synthesized ABC linear triblock copolymers, i.e., polystyrene-b-poly(ethylene oxide)-b-polylactide, via sequential anionic and ring-opening polymerizations. In the first anionic polymerization step, styrene was polymerized in cyclohexane using sec-butyllithium as the initiator. Poly (styryl) lithium was hydroxylated by the addition of ethylene oxide, and the subsequent protonation with methanolic HCl. In the second anionic polymerization step, potassium naphthalenide was used to deprotonate the hydroxyl group of the PS to generate the macroinitiator of PS-$O^-K^+$. Polymerization of ethylene oxide was performed in THF and terminated with methanolic HCl. In the ring-opening polymerization step, the PS-b-PEO-$AlEt_2$ macroinitiator was prepared from an $AlEt_3$/pyridine system in THF, and the polymerization of lactide was performed at $90^{\circ}C$. The resulting block copolymers showed well-defined molecular weights and narrow molecular weight distributions as revealed by $^1H$- NMR spectroscopy and gel permeation chromatography (GPC).

• Journal of Oral Medicine and Pain
• /
• v.22 no.1
• /
• pp.95-109
• /
• 1997

The purpose of this research is to investigate the influence on mandibular movements and TMJ sounds with changes of head and neck posture. For the research, twenty patients who had complained of TMJ sounds without any other symptoms of cranio-mandibular disorders, were selected as subjects for measurements of TMJ sounds, and radiographs on transcranial view of TMJ were taken on ten of the subjects. From NHP, UHP, DHP and FHP, aspects of mandibular movement and TMJ sound were investigated from each posture. Aspects of mandibular movement and TMJ sound were observed by measuring total vibration energy(Integral), peak amplitude, maximum amound of mouth opening, and TMJ sound-emitting point using Sonopak for windows (version 1.33) and Bio-EGN(Bioresearch Inc. WI. U.S.A.). Head and neck movement-measuring instrument, CROM(perfomance attainment Inc. U.S.A.) was to maintain even head posture. Degrees of inclination of UHP and DHP were determined at 30' and distance of FHP was 4cm. The results obtained were as follows. 1. Total vibration energy and peak amplitude of TMJ sounds were decreased more on UHP and on UHP and increased more on DHP and FHP than that on NHP. 2. At the maximum mouth opening, distance of TMJ sound-emitting point were decreased more on UHP and increased more on DHP and FHP than that on NHP. 3. The amounts of the maximum mouth opening were increased more on UHP and decreased more on DHP and FHP than that on NHP. 4. For the changes of the head posture with mouth opening observed in radiograph, condylar head was positioned more lower-anteriorly on UHP, and more upper-posteriorly on DHP and FHP than that on NHP. From the results obtained as above, considering positive influence of the change of head and neck posture, avoiding down-head and forward-head posture, and recommending upper- head posture can prevent the progress of temporomandibular disorder and lead to successful treatment for the patients with temporomandibular joint sounds.

• Tunnel and Underground Space
• /
• v.29 no.1
• /
• pp.64-74
• /
• 2019

Behavior of a rock block consisting of rock joints during excavation of an underground opening is an important factor for the mechanical stability of the opening. In this study, the behavior of a rock block under different geostatic stress and joint property conditions was analyzed quantitatively. The behavior of the rock block analyzed by 3DEC numerical analysis was compared with that of the theoretical calculation, and the error between the theoretical value and the numerical analysis result was analyzed under various geostatic stress and joint property conditions. The result of the stability analysis of a rock block showed less than 5% of error with numerical simulation result, which verified the applicability of the purposed analytic solution.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.21 no.9
• /
• pp.78-84
• /
• 2022

An air circuit breaker (ACB) is an electrical protection device that interrupts abnormal fault currents that result from overloads or short circuits in a low-voltage power distribution line. The ACB consists of a main circuit part for current flow, mechanism part for the opening and closing operation of movable conductors, and arc-extinguishing part for arc extinction during the breaking operation. The driving mechanism of the ACB is a spring energy charging type. The faster the contact opening speed of the movable conductors during the opening process, the better the breaking performance. However, there is a disadvantage that the durability of mechanism decreases in inverse proportion to the use of a spring capable of accumulating high energy to configure the breaking speed faster. Therefore, to simultaneously satisfy the breaking performance and mechanical endurance of the ACB, its driving mechanism must be optimized. In this study, a dynamic model of the ACB was developed using the MDO(Mechanism Dynamics Option) module of CREO, which is widely used in multibody dynamics analysis. To improve the opening velocity, the Taguchi design method was applied to optimize the design parameters of an ACB with many linkages. In addition, to evaluate the improvement in the operating characteristics, the simulation and experimental results were compared with the MDO model and improved prototype sample, respectively.