• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2012년도 춘계학술발표대회
• /
• pp.109.1-109.1
• /
• 2012

본 연구에서는 co-sputtering을 통한 $WO_3$와 $In_2O_3$ 타겟을 사용하여 $WO_3$ 파워에 따른 Tungsten(W)-doped $In_2O_3$ (IWO) 투명 전극의 전기적, 광학적, 구조적 특성을 연구하고 이를 활용한 유기태양전지(Organic Photovoltaics; OPVs)의 특성을 분석하였다. Tungsten의 doping 농도는 $WO_3$에 인가되는 Radio-frequency (RF) power를 5~30 W 까지 변화시켜 조절하였으며, Rapid Thermal Annealing (RTA) 후 열처리 공정을 통해 IWO 박막의 전기적, 광학적, 구조적 특성을 분석하였다. Hall measurement 및 UV/Vis spectrometry 분석을 통하여 가시광선 영역에서 80% 이상의 높은 투과율, $48\;cm^2\;V^{-1}\;s^{-1}$의 홀 이동도, 20 ${\Omega}/{\Box}$ 이하의 낮은 면저항과 $3.2{\times}10^{-4}\;{\Omega}-cm$의 비저항 값을 나타내었다. 최적화된 IWO 박막을 이용한 OPV 셀 특성은 fill factor(FF): 61.59 %, short circuit current($J_{SC}$): 8.84 $mA/cm^2$, open circuit voltage($V_{OC}$): 0.60 V, efficiency(PCE): 3.27 %로 ITO로 제작된 OPV 샘플과 비교하였을 때 ITO를 대체할 수 있는 고이동도의 새로운 투명 전극 재료로서의 가능성을 확인하였다.

• 한국재료학회지
• /
• 제23권1호
• /
• pp.35-40
• /
• 2013

In this study, the influence on the surface passivation properties of crystalline silicon according to silicon wafer thickness, and the correlation with a-Si:H/c-Si heterojunction solar cell performances were investigated. The wafers passivated by p(n)-doped a-Si:H layers show poor passivation properties because of the doping elements, such as boron(B) and phosphorous(P), which result in a low minority carrier lifetime (MCLT). A decrease in open circuit voltage ($V_{oc}$) was observed when the wafer thickness was thinned from $170{\mu}m$ to $50{\mu}m$. On the other hand, wafers incorporating intrinsic (i) a-Si:H as a passivation layer showed high quality passivation of a-Si:H/c-Si. The implied $V_{oc}$ of the ITO/p a-Si:H/i a-Si:H/n c-Si wafer/i a-Si:H/n a-Si:H/ITO stacked layers was 0.715 V for $50{\mu}m$ c-Si substrate, and 0.704 V for $170{\mu}m$ c-Si. The $V_{oc}$ in the heterojunction solar cells increased with decreases in the substrate thickness. The high quality passivation property on the c-Si led to an increasing of $V_{oc}$ in the thinner wafer. Short circuit current decreased as the substrate became thinner because of the low optical absorption for long wavelength light. In this paper, we show that high quality passivation of c-Si plays a role in heterojunction solar cells and is important in the development of thinner wafer technology.

• Bulletin of the Korean Chemical Society
• /
• 제35권5호
• /
• pp.1449-1454
• /
• 2014

The co-sensitization of N719 with a cyclic thiourea functionalized organic dye, coded AZ5, for dye-sensitized solar cells (DSSCs) was demonstrated. Due to its intensive absorption in ultraviolet region, AZ5 could compensate the loss of light harvest induced by triiodide, thereby the short-circuit photocurrent density ($J_{sc}$) was increased for co-sensitized (N719+AZ5) DSSC. Moreover, the electron recombination and dye aggregation were retarded upon N719 cocktail co-sensitized with AZ5, thus the open-circuit voltage ($V_{oc}$) of co-sensitized device was enhanced as well. The increased $J_{sc}$ (17.9 $mA{\cdot}cm^{-2}$) combined with the enhanced $V_{oc}$ (698 mV) ultimately resulted in an improved power conversion efficiency (PCE) of 7.91% for co-sensitized DSSC, which was raised by 8.6% in comparison with that of N719 (PCE = 7.28%) sensitized alone. In addition, co-sensitized DSSC exhibited a better stability than that of N719 sensitized device probably due to the depression of dye desorption.

• 센서학회지
• /
• 제7권1호
• /
• pp.67-72
• /
• 1998

Plused ArF excimer laser ablation과 열증착법에 의해 p형 Si 기판위에 PbTe/CuPc 박막을 증착하였다. 성장된 박막의 구조적, 전기적 특성은 XRD, 전류-전압 곡선등의 분석으로 행하였다. XRD 분석으로부터 PbTe박막과 CuPc 박막은 a 축의 배향성을 지닌 박막으로 성장하였음을 알 수 있었다. PbTe/CuPc/Si 박막의 광전특공을 조사하기 위하여 빛을 조사했을 때와 빛을 조사하지 않았을 때의 수직방향의 전류-전압 (I-V) 특성을 CuPc/Si, PbTe/Si 단층막의 특성과 비교 관찰하였다. PbTe/CuPc/Si 박막에서 단축 광전류 ($J_{sc}$)가 $25.46\;mA/cm^{2}$, 개회로 광전압 ($V_{oc}$)이 170 mV인 커다란 광기전력 특성을 나타내었다. 또한 양자효율 (QE)은 15 %, 광전변환효율 (${\eta}$)은 $3.46{\times}10^{-2}$로 측정되었다. QE와 ${\eta}$를 기초로 한 PbTe/CuPc/Si 접합과 광전류 과정은 CuPc 층에서의 광캐리어 생성, PbTe/CuPc 계면에 의 광캐리어 분리 그리고 PbTe층에서의 광캐리어 운송 역할이 효율적으로 수행된 결과임을 알 수 있었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.154.2-154.2
• /
• 2016

In this work, we introduce a solution-processed CdS interlayer for use in inverted bulk heterojunction (BHJ) solar cells, and compare this material to a series of standard organic and inorganic cathode interlayers. Different combinations of solution-processed CdS, ZnO and conjugated polyelectrolyte (CPE) layers were compared as cathode interlayers on ITO substrates to construct inverted solar cells based on $PTB7:PC_{71}BM$ and a $P3HT:PC_{61}BM$ as photoactive layers. Introduction of a CdS interlayer significantly improved the power conversion efficiency (PCE) of inverted $PTB7:PC_{71}BM$ devices from 2.0% to 4.9%, however, this efficiency was still fairly low compared to benchmark ZnO or CPE interlayers due to a low open circuit voltage ($V_{OC}$), stemming from the deep conduction band energy of CdS. The $V_{OC}$ was greatly improved by introducing an interfacial dipole (CPE) layer on top of the CdS layer, yielding outstanding diode characteristics and a PCE of 6.8%. The best performing interlayer, however, was a single CPE layer alone, which yielded a $V_{OC}$ of 0.727 V, a FF of 63.2%, and a PCE of 7.89%. Using $P3HT:PC_{61}BM$ as an active layer, similar trends were observed. Solar cells without the cathode interlayer yielded a PCE of 0.46% with a poor $V_{OC}$ of 0.197 V and FF of 34.3%. In contrast, the use of hybrid ZnO/CPE layer as the cathode interlayer considerably improved the $V_{OC}$ of 0.599 V and FF of 53.3%, resulting the PCE of 2.99%. Our results indicate that the CdS layer yields excellent diode characteristics, however, performs slightly worse than benchmark ZnO and CPE layers in solar cell devices due to parasitic absorption below 550 nm. These results suggest that the hybrid inorganic/organic interlayer materials are promising candidates as cathode interlayers for high efficiency inverted solar cells through the modification of interface contacts.

• 한국전기전자재료학회논문지
• /
• 제28권11호
• /
• pp.731-736
• /
• 2015

Rhodamine B (RhB) was utilized as a dye sensitizer for dye-sensitized solar cells (DSSCs) and its photovoltaic property was examined under the illumination of AM 1.5 G, $100mWcm^{-2}$. DSSCs based on RhB exhibited typical photovoltaic properties with an open-circuit voltage ($V_{OC}$) of 0.34 V, a short-circuit current ($J_{SC}$) of $1.55mA{\cdot}cm^{-2}$, a fill factor (FF) of 50%, and a conversion efficiency (PCE) of 0.26%. In order to further improve the photovoltaic properties of RhB-based DSSCs, the effect of (i) incorporating a strong electron-donating NCS unit into the RhB molecular backbone, (ii) combining a bis-negatively charged zinc complex anion ($Zn-dmit_2$, dmit=di-mercapto-dithiol-thione) with the amine cation of RhB, (iii) co-adsorbing RhB dyes with chenodeoxycholic acid (CDCA) molecules onto porous $TiO_2$ electrodes, was investigated and discussed.

• Bulletin of the Korean Chemical Society
• /
• 제32권6호
• /
• pp.2058-2062
• /
• 2011

The effect of the addition of ionic liquids with four different cations (imidazolium, pyrrolidinium, piperidinium and pyridinium) on the performance of dye-sensitized $TiO_2$ solar cells based on electrolytes containing a t-butylpyridine (TBP) in 3-methoxypropionitrile (MPN) was studied. A total of 18 ionic liquids with mono-, di- and tri-alkyl derivatives were used in the present study, and among them a pyridinium cation with a mono-alkyl group showed better cell efficiency than the others. The best photoelectric conversion efficiency, 7.213%, was obtained using 1-hexylpyridinium iodide with an open-circuit photovoltage ($V_{oc}$) = 0.731 V, a short-circuit photocurrent density ($J_{sc}$) = 16.175 $mA/cm^2$, and a fill factor (ff) = 0.610 under AM1.5 and 100 $mW/cm^2$ illumination.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 추계학술대회 논문집
• /
• pp.309-311
• /
• 2007

Supramolecules containing double hydrogen bonding sites at their both chain ends were self-polymerized to become solid state polymer and were utilized to improve the efficiency of solid state DSSCs. Hydrogen bonding sites were attached at the chain ends of PEG of Mw=2000, such as pyrimethamine and glutaric acid. The solar cell with the solid state supramolecular polymer electrolyte resulted in the overall energy conversion efficiency of 4.63 % with a short circuit current density $(J_{sc})$ of 10.41 $mAcm^{-2}$, an open circuit voltage $V_{oc}$, of 0.71 V and a fill factor (FF) of 0.62 at one sun condition ([oligomer]:[1-methyl-3-propyl imidazolium iodide (MPII)]:$[I_2]$ = 20 : 1 : 0.19, active area = 0.16 $cm^2$, $TiO_2$ layer thickness = 10 ${\mu}m$). The ionic conductivity of the sol id state electrolyte was $5.11{\times}10^{-4}$ (S/cm). The cell performance was characterized by electrochemical impedance spectroscopy and ionic conductivity.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2011년도 추계학술대회 초록집
• /
• pp.57.1-57.1
• /
• 2011

We studied the performance of CdSe nanoparticle in the active layer of organic photovoltaics (OPVs) by changing concentration of the CdSe NPs in the P3HT:PCBM layer. We observed that the absorption peak value gradually increases with the increasing amount of CdSe NPs at 600nm wave length. However, the electrical properties of OPVs correspond less with the tendency of UV/visible result. The highest performance was shown with 10% of CdSe NPs. The device performance decreased after 10% of CdSe NPs, this shows the dependencies of performanc of hybrid solar cells on the CdSe NPs loading amount. The resulting OPVs with 10 % of CdSe NPs show a short circuit current density ($J_{sc}$) of $6.96mA/cm^2$, open circuit voltage ($V_{oc}$) of 0.61V, fill factor (FF) of 0.59, and power conversion efficiency (PCE) of 2.53% under AM 1.5 ($100mW/cm^2$).

• 한국진공학회지
• /
• 제18권5호
• /
• pp.390-393
• /
• 2009

유기물 기반의 전자 소자에서 소자간의 전기적인 전류 흐름 및 기생저항 등을 차단하기 위하여 표면 에너지를 이용한 새로운 패터닝 기법을 제안하였다. 소수성의 perfluoro-alkyl fluorosilanes을 플라즈마 이온 에칭을 이용하여 선택적으로 친수성으로 변환한 뒤 wettability 현상을 통해 유기 물질을 자동 패터닝 하였다. 또한 이 기법을 이용하여 $V_{oc}$ (open circuit voltage): 482 mV, $J_{sc}$ (short circuit current density): 2.4 mA/$cm^2$, FF (Fill factor): 0.58, $\eta$ (Efficiency): 0.95 % 의 특성을 보이는 bulk-이종접합 유기 태양 전지 소자를 제작하였다.