• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.3
• /
• pp.684-690
• /
• 2010

Most of the existing SoCs have shared bus architecture which always has a bottleneck state. The more IPs are in an SOC, the less performance it is of the SOC, Therefore, its performance is effected by the entire communication rather than CPU speed. In this paper, we propose cross-bar switch bus architecture for the reduction of the bottleneck state and the improvement of the performance. The cross-bar switch bus supports up to 8 masters and 16 slaves and parallel communication with architecture of multiple channel bus. Each slave has an arbiter which stores priority information about masters. So, it prevents only one master occupying one slave and supports efficient communication. We compared WISHBONE on-chip shared bus architecture with crossbar switch bus architecture of the SOC platform, which consists of an OpenRISC processor, a VGA/LCD controller, an AC97 controller, a debug interface, a memory interface, and the performance improved by 26.58% than the previous shared bus.

• Proceedings of the IEEK Conference
• /
• 2004.06b
• /
• pp.529-532
• /
• 2004

The ECC(Elliptic Curve Cryptogrphics), one of the representative Public Key encryption algorithms, is used in Digital Signature, Encryption, Decryption and Key exchange etc. The key operation of an Elliptic curve cryptosystem is a scalar multiplication, hence the design of a scalar multiplier is the core of this paper. Although an Integer operation is computed in infinite field, the scalar multiplication is computed in finite field through adding points on Elliptic curve. In this paper, we implemented scalar multiplier in Elliptic curve based on the finite field GF($2^{163}$). And we verified it on the Embedded digital system using Xilinx FPGA connected to an EISC MCU. If my design is made as a chip, the performance of scalar multiplier applied to Samsung $0.35 {\mu}m$ Phantom Cell Library is expected to process at the rate of 8kbps and satisfy to make up an encryption processor for the Embedded digital doorphone.

• Annual Conference of KIPS
• /
• 2005.05a
• /
• pp.1071-1074
• /
• 2005

The ECC(Elliptic Curve Cryptogrphics), one of the representative Public Key encryption algorithms, is used in Digital Signature, Encryption, Decryption and Key exchange etc. The key operation of an Elliptic curve cryptosystem is a scalar multiplication, hence the design of a scalar multiplier is the core of this paper. Although an Integer operation is computed in infinite field, the scalar multiplication is computed in finite field through adding points on Elliptic curve. In this paper, we implemented scalar multiplier in Elliptic curve based on the finite field $GF(2^{163})$. And we verified it on the Embedded digital system using Xilinx FPGA connected to an EISC MCU(Agent 2000). If my design is made as a chip, the performance of scalar multiplier applied to Samsung $0.35\;{\mu}m$ Phantom Cell Library is expected to process at the rate of 8kbps and satisfy to make up an encryption processor for the Embedded digital information home system.

• Proceedings of the Korea Institute of Convergence Signal Processing
• /
• 2001.06a
• /
• pp.89-92
• /
• 2001

In this paper, as a study of programmable software radio digital communication, we implemented ASK(Amplitude Shift Keying), FSK(Frequency Shift Keying), and PSK(Phase Shift Keying) modulation using programmable software(algorithm) of DSP(Digital Signal Processor). Moreover, it is possible to select one of those three modulation methods by realizing on single DSP. We adopted Motorola DSP56002 and Crystal CS4215(A/D and D/A converter) for our purpose. The DSP56002 is 24-bit and operates 20 MIPS at 40 MHz, and the CS4215 is 16-bit and supports the maximum 50 kHz sampling frequency.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2013.05a
• /
• pp.345-348
• /
• 2013

This paper provides a method for compression and transmission of on-chip bus data. As the data traffic on on-chip buses is rapidly increasing with enlarged video resolutions, many video processor chips suffer from a lack of bus bandwidth and their IP cores have to wait for a longer time to get a bus grant. In multimedia data such as images and video, the adjacent data signals very often have little or no difference between them. Taking advantage of this point, this paper develops a simple bus data compression method to improve the chip performance and presents its hardware implementation. The method is applied to a Video Codec - 1 (VC-1) decoder chip and reduces the processing time of one macro-block by 13.6% and 10.3% for SD and HD videos, respectively.

• Journal of Computing Science and Engineering
• /
• v.4 no.3
• /
• pp.189-206
• /
• 2010

It is generally accepted that dynamic voltage scaling (DVS) is one of the most effective techniques of energy minimization for real-time applications in embedded system design. The effectiveness comes from the fact that the amount of energy consumption is quadractically proportional to the voltage applied to the processor. The penalty is the execution delay, which is linearly and inversely proportional to the voltage. According to the granularity of tasks to which voltage scaling is applied, the DVS problem is divided into two subproblems: inter-task DVS problem, in which the determination of the voltage is carried out on a task-by-task basis and the voltage assigned to the task is unchanged during the whole execution of the task, and intra-task DVS problem, in which the operating voltage of a task is dynamically adjusted according to the execution behavior to reflect the changes of the required number of cycles to finish the task before the deadline. Frequent voltage transitions may cause an adverse effect on energy minimization due to the increase of the overhead of transition time and energy. In addition, DVS needs to be carefully applied so that the dynamically varying chip temperature should not exceed a certain threshold because a drastic increase of chip temperature is highly likely to cause system function failure. This paper reviews representative works on the theoretical solutions to DVS problems regarding inter-task DVS, intra-task DVS, voltage transition, and thermal-aware DVS.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.5C
• /
• pp.454-464
• /
• 2002

In the ATM-PON (Asynchronous Transfer Mode-Passive Optical Network), the downstream cell transmitted by an OLT is broadcast to all ONUs. The ONU receives selectively its own cells by VP filtering. On the other hand, the upstream cell can be transmitted by ONU in the case of receiving a grant from the OLT. After providing the grant to an ONU, the OLT expects the arrival of a cell after an elapse of the equalized round trip delay. ITU-T G.983.1 recommends that one bit error is allowed between the expected arrival time and the actual arrival time at the OLT. Because the ONU processes the different delay to each type of grant (ranging, user cell, and mimi-slot grant), it is not simple to design the transmission part of ONU. In this paper, we implement a grant processor which provides the delay accurately in the ONU TC chip with the FPGA. For the given equalized delay, it deals with the delay for the cell, the byte, and the bit unit by using the shift register, the byte counter, and the D flip-flop, respectively. We verify the operation of the grant processor by the time simulation and the measurement of the optical board output.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.04a
• /
• pp.305-311
• /
• 2003

We propose a new technique of adaptive-neuro controller design to implement real-time control of robot manipulator, Unlike the well-established theory for the adaptive control of linear systems, there exists relatively little general theory for the adaptive control of nonlinear systems. Adaptive control technique is essential for providing a stable and robust performance for application of robot control. The proposed neuro control algorithm is one of loaming a model based error back-propagation scheme using Lyapunov stability analysis method. Through simulation, the proposed adaptive-neuro control scheme is proved to be a efficient control technique for real time control of robot system using DSPs(TMS320C50)

• Journal of Advanced Marine Engineering and Technology
• /
• v.17 no.5
• /
• pp.86-98
• /
• 1993

The application of A.C. motor for servo system is rapidly increased according to the recent advance of power electronics and digital control techniques. The induction motor which has a simple structure and needs less maintenance has become to be used widely in the industrial field for the speed and position control recently. In this paper, the full-bridge resonant inverter is applied to the speed control of single phase inducting motor. The digital PID control algorithm is used and the control parameter is determined by the Zigler-Nichols transient response method. The speed control is carried out by the one chip micro-processor(intel EV 8097BH) and control program is developed by the assembly language. By the experimental result, it is confirmed that the speed of single phase induction motor driven by full bridge series inverter can be smoothly controlled by a digital PID controller.

• Proceedings of the KIPE Conference
• /
• 2006.06a
• /
• pp.222-224
• /
• 2006

To improve the drawback of LCMPPT(Limit Cycle Maximum Power Point Tracking) controller of the existing two power conversion stages, an advanced MPPT scheme of single power conversion stage is proposed in this paper. This topology is faster on the control speed by means of current control method and the system configuration is simpler. The Authors produce a battery charger by using a cost effective one-chip processor (PIC16F877A) and evaluate another application on the basis of simulation. As a result, the proposed new LCMPPT algorithm is confirmed to be stable and useful.