• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.3104-3110
• /
• 2011

This paper describes how to ensure safety of train by guaranteeing stable and continuous communication in RF-CBTC. CBTC System uses the wireless communication between onboard and wayside so that safety of wireless communication is the most important. Losing the position of train causes vital problem of train service. By losing the position of train, the other trains are blocked in the block and the train move by emergency mode so headway and safety cannot guaranteed. Therefore, safety is ensured by redundancy of wireless equipment. One of the ways to make redundancy is redundancy of equipment. However, the redundancy of equipment spends a lot of money to avoid interference in limited place like underground. Continuous communication is guaranteed by means of redundancy of wireless communication coverage to solve the problems even though one of the equipment is broken.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집B
• /
• pp.593-598
• /
• 2000

Experimental study is conducted to clarify the pneumatic characteristics of brake system for freight train. Empty-load and diaphragm brake systems are mainly installed in the freight trains owned by KNR(Korean National Railroad). Experimental train set is composed of sixteen freight train and one diesel locomotive that are now in use. From the experimental results, in case of commercial brake, empty-load brake system responds to the brake command more slowly than the diaphragm brake system. But, in case of release command, the response time of diaphragm brake system is shorter than that of empty-load one. In the emergency brake test, the decreasing rate of brake pipe pressure of tenth car is almost same that of decreasing rate of commercial brake service.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집 특별세미나,특별/일반세션
• /
• pp.483-488
• /
• 2009

When a train enters into the tunnel with high speed, a compression wave generated inside the tunnel has been studied as a one-dimensional phenomenon. However, one-dimensional approach can't analyze 3-dimensional flow effect in the vicinity of the train body. In this research, so as to overcome this weak point, a prediction method of the wavefront of a compression wave using steady state solution has been used for the parametric study considering 3-dimensional effects of the interactions between trains and tunnels. The effective hood shapes were deduced in both cases of the train's entry into the tunnel on the single track and on a side of the double track. As a result, in case of the train's entry on a side of the double track, the increase of compression wave value propagated to the tunnel inside have appeared compared with the train's entry on the single track. Also, a horizontally convex elliptic hood shape is more effective at the train's entry on a side of the double track for the purpose of a decrease of wavefront gradient of a compression wave.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.138-141
• /
• 2008

The screen doors installed in the station of subway are subject to the train-wind pressure caused by the operation of trains. The train-wind pressure has to be correctly estimated for the design of safe structure of screen doors. As three-dimensional numerical flow analysis technology has been significantly developed, the analysis on the train-wind pressure with diverse variables such as train specifications, train speed, tunnel and station configurations, and blockage ratio can be effectively carried out with three-dimensional numerical method. In this study, computational analysis of train-induced wind in a subway tunnel employing the screen doors are carried out by using the three-dimensional numerical method with the model of the moving boundary for the run of trains. While the numerical analysis of train-wind pressure was applied on the one island-type station in the Seoul Subway Line 2, maximum pressure of 494 Pa was estimated on the screen door when two trains pass each other at the speed of 80km/h in the platform.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 1998년도 창립기념 춘계학술대회 논문집
• /
• pp.596-603
• /
• 1998

The entry compression wave, which is generated at the entrance of the tunnel, is almost always associated with the pressure transients in the tunnel as well as the impulse noise at the exit of the tunnel. It is highly required to design the train nose shape that can minimize such undesirable phenomena. The objective of the current work is to investigate the effects of the train nose shape on the entry compression wave. Numerical computations were applied to one-dimensional unsteady compressible flow in high-speed railway train/tunnel systems. A various shape of train noses were tested for a wide range of train speeds. The results showed that the strength of the entry compression wave is not influenced by the train nose shape, but the time variation of pressure in the entry compression wavefront is strongly related to the train nose shape. The current method of the characteristics was able to represent a desirable nose shape for various train speeds. Optimum nose shape was found to considerably reduce the maximum pressure gradient of the entry compression wave.

• 한국안전학회지
• /
• 제22권5호
• /
• pp.71-76
• /
• 2007

Failures of equipments for train control systems are linked directly to extensive damages of human lives or financial losses from the increasing uses of train control equipments utilizing computers. Then safety activities for assuring safety and reliability are needed during the system life-cycle. Risk analysis is important phase to increase safety from determining the risk presented by the identified hazard. In this paper, we investigated several methods for risk estimation of safety activities, and then we drew a comparison between original methods to suggest optimized one in the application to train control systems. In the result of the comparison, we had plan to propose the risk analysis method called Best-Practice(BP) risk method combining advantages of the qualitative and the quantitative analysis. In addition, we attempted to apply the BP-risk method to domestic train control systems handling in Korea.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 춘계학술대회 논문집
• /
• pp.686-693
• /
• 2003

An intensive study was conducted for crashworthiness structural design of recently developed Korean High Speed Train. Two nam design concepts are setup to protect the both crews and passengers from serious injury at heavy collision accidents, and to reduce damages of the train itself at light collision accidents. For occupant protection a collision against a movable 15 tons rigid obstacle at 110 kph and a train-to-train collision at 30 kph were selected as accident scenarios for the heavy collisions based on the train accident investigations. A train-to-train collision at 8 kph was used for the light collisions. The crashworthiness behaviors of KHST have been evaluated numerically using the finite element method. Also, one-dimensional collision analyses show good crashworthy responses in a full rake consist and 3-dimensional shell element analyses do in the front-end structures of the power car. Occupant analyses and sled tests demonstrated that KHST performs well enough to protect occupants under the considered accident scenarios.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 추계학술대회 논문집
• /
• pp.1005-1009
• /
• 2005

The On Board Computer System (ORCS) used for rolling stocks is one of the core equipments in trains, which deals with collecting real-time data of a train to display and record the train's statuses, control the train, and support the driver and maintenance function. Resides, due to high reliability and high speed communication required lately for various electronics including signal1ing devices, train protection system, and multimedia, the necessity of a more robust train communication network is on the lise. This study aims at understanding the technological trend of the current train communication network in order to rapidly cope with the tendency above and providing fundamental data for designing a more advanced communication network for high-speed trains hereafter.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.387-392
• /
• 2005

Double-deck train have studied in the next generation train in KRRI. Double-deck train have more seat capacities compared with single deck vehicles and is a efficient, reliable and comfortable alternative train. Because of heavy weight, weight minimization of double-deck train carbody is imperative to reduce cost and extend life-time of train. Weight minimization problem of the double-deck train car-body is required to decide 66 design variables of thicknesses for large aluminum extruded panel while satisfying stress constraints. Design variables are too many and one execution of structural analysis of double-deck train carbody is time-consuming. Therefore, we adopt approximation technique to save computational cost of optimization process. Metamodels such as response surface model (RSM) and kriging model are used to approximate model-based optimization is described. RSM is easy to obtain and expressed explicit function, but this is not suitable for highly nonlinear and large scaled problems. Kriging model employs an interpolation scheme and is developed in the fields of spatial statistics and geostatistics. Target of this design is to find optimum thickness of AEP to minimize weight of doulbe-deck train carbody. In this study, meta model techniques are introduced to carry out weight minimization of a double-deck train car-body.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.1841-1848
• /
• 2010

Electric railway system consist of rolling stock, track, signal and streetcar line system. ATP(Automatic Train Protection) system in railway signaling system is the important one grasping the position and velocity of a train. The wayside transmitter of ATP system is installed between rails. Recently, the research about increasing train speed has been developed in total departments of the railroad systems. The study on the information transmission between on-board transmitter and wayside transmitter is required for increasing the train speed in the ATP system. When the train speed is increased as to same transmissi on distance, the problem on information transmission occurs because the transmission time is decreased. In case that the transmission distance is extended, the transmission time is decreased with respect to the train speed. Therefore, we have to define the standard magnetic intensity as to the train speed in order to transmit correctly telegram. In this paper, the transmission distance for the telegram is suggested on the basis of the train speed. Also, the standard magnetic intensity from the wayside transmitter to on-board transmitter is proposed by using transmission distance regarding the train speed in the ERTMS/ETCS system by using Matlab program.