• 센서학회지
• /
• 제31권1호
• /
• pp.51-56
• /
• 2022

In this study an efficient method for detecting and monitoring engine misfiring, focusing on minute speed changes in the crankshaft is proposed., Its validity is verified using various misfiring cases. Typically, the crankshaft speed fluctuates around the normal value depending on the engine misfiring status. Even a minute speed change in the crankshaft can be estimated by measuring the rotation time of each tooth of the 118-tooth flywheel attached to the crankshaft with a 2-MHz timer. Therefore, a speed pattern for an in-line six-cylinder engine consists of 236 tooth rotation speeds corresponding to the two rotations of the crankshaft, in which all the cylinders complete four-stroke cycle. FFT analysis can reduce the number of components of a speed pattern from 236 to just four major components: - fundamental frequency_(f), 2f, 3f, 6f., - This makes the comparison of the misfiring cases simpler and faster. In the experiment, five engine status cases (one normal firing and, four misfiring cases) were simulated. While the 6f component was the largest for the normal case, the f component increased as misfiring occurred one, two apart, and two consecutive times. The 3D FFT pattern comprising the ratio of f, 2f, and 3f, 6f showed that the distance between the misfiring and normal states was larger

• Journal of Advanced Marine Engineering and Technology
• /
• 제12권1호
• /
• pp.28-36
• /
• 1988

Since the oil shocks of 1970s, the quality of the fuel oil for marine diesel engines has become more degarded than ever. When the poorer quality fuel is burned, carbon residues of the fuel oil cause blockage of the fuel injection valve nozzle and troubles of fuel injection system. The mis-firing of engine occurs due to the decrease of fuel quantity injected, the decrease of compression pressure in the slow speed range, the increase of fuel leaked and the high ignition temperature of degraded fuel etc. This paper is to investigate theoretically the effects of mis-firing on the crankshaft axial vibration of diesel engine. The cylinder pressure in operation is calculated by the computer aided simulation of closed cycle for a large two-stroke diesel engine and also the exciting force of axial vibration and the resonance amplitudes are calculated. And then, the condition of normal state, misfiring and one-cylinder cut-off operation are analyzed. The results of calculations show good agreements with those of the actual measurements.

• 한국자동차공학회논문집
• /
• 제6권1호
• /
• pp.80-89
• /
• 1998

The residual gas in an spark-ignition engine is one of important factors on emissions and performance such as combustion stability. With high residual gas fractions, flame speed and maximum combustion temperature are decreased and these are deeply related with combustion stability especially at idle and NOx emission at relatively high engine load. Therefore, there is a need to characterize the residual gas fraction as a function of the engine operating load. Therefore, there is a need to characterize the residual gas fraction as a function of the engine operating parameters. In the present study, the quantitative measurement technique of residual gas fraction was studied by using Fast Response Flame Ionization Detector(FRFID). The measuring technique and model for estimation of residual gas fraction were reported in this paper. By the assuming that the raw signal from FRFID saturates with the same slope for firing and misfiring cycle, in-cylinder hydrocarbon(HC) concentration can be estimated. Residual gas fraction can be obtained from the in-cylinder HC concentration measured at firing and motoring condition. The developed measurement and calibration procedure were applied to the limited engine operating and design condition such as intake manifold pressure and valve overlap. The results show relevant trends by comparing those from previous studies.

• 소음진동
• /
• 제10권4호
• /
• pp.655-661
• /
• 2000

Diesel power plant can be used as a power supplier for the isolated place where consumption of electric power is variable. The reason is that mobility and durability of diesel engine is superior to those of other thermal engines. However, there are some disadvantages for using these diesel engines such as bigger vibratory excitation force comparing to the others, which result from high combustion pressure of cylinders and inertia force of piston reciprocating masses. In this paper, control and optimization of torsional vibration of 12K90MC-S engine for diesel power plant using uneven crank angles is identified by theoretical analysis and vibration measurement.

• 대한조선학회논문집
• /
• 제31권4호
• /
• pp.157-166
• /
• 1994

최근의 배는 에너지절약을 도모하기 위하여 디이젤기관이 대구경 장행정 소수실린더 저속회전화 추세에 있기 때문에 기진력이 커지고 있다. 이와같은 결과로 추진축계에 과잉비틂진동응력이 작용하게 되어 선박운항에 지장을 줄 정도의 플로렐러축의 결손사고가 종종 발생하곤 한다. 현재까지의 추지축계에 대한 설계 및 비틂진동해석은 대부분 축계의 비틂기진력이 확정적이란 가정하에 수행되어 왔다. 이와 관련하여 축계 비틂기진력의 불규칙성의 영향을 고려한 확률적 비틂진동해석에 관한 연구가 이루워지고 있다. 본 연구에서는 기관기진력의 확률변수를 고려하여 추진축계의 강제 비틂진동의 확률적 해석에 대한 새로운 방법을 제시하였다. 확률적 해석에 응답면이론과 Monte Carlo 시뮤레이션 방법이 이용되었다. 본 해석방법의 타당성 여부를 확인하기 위하여 Nikolaidis 등이 사용한 시산대상선에 대한 일련의 수치계산을 수행하고, 그 결과를 Nikolaidis 등의 연구결과와 비교 검토하여 본 결과 비교적 잘 일치하고 있음을 미루어 보아 본 해석방법이 타당성이 확인되었다.