• Journal of electromagnetic engineering and science
• /
• v.10 no.1
• /
• pp.13-17
• /
• 2010

In this paper, we have described a simple CPW-fed UWB antenna for wireless UWB communication. The proposed antenna consists of two symmetrical strips having two steps and CPW feeding. Two techniques(symmetrical structure, two steps) are used to produce good low-dispersion and impedance matching. The proposed UWB antenna has an omni directional radiation pattern, compact size, low dispersion, and low cost.

• Journal of electromagnetic engineering and science
• /
• v.8 no.1
• /
• pp.1-5
• /
• 2008

In this paper, a biconical type antenna is proposed for EMI test site validation above 1 GHz. To achieve broadband and omni-directional radiation patterns required by international standard(CISPR), the proposed antenna consists of general bicones with cylindrical loads and adopts side feeding method to minimize the influence on H-plane pattern due to feeding cable, balun, and connector. The radiation patterns of the fabricated antenna are measured and the results are compared with CISPR criteria and commercial antenna in our interest frequencies. Although the proposed antenna has a few problems in frequency range of 1 GHz to 2 GHz, it has relatively better performance than commercial antenna.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.8
• /
• pp.443-446
• /
• 2004

In this paper, a multi-band ceramic chip antenna for WLAN(Wireless LAN) applications is designed. The design target is to obtain 0 dBi of coverage gain with omni directional radiation pattern. The antenna is fabricated using Low Temperature Co-fired Ceramic(LTCC) technology. The size of the chip antenna is $2.2{\times}9.65{\times}1.02$mm. The measured antenna gain is 1 dBi at 2.44 GHz and 0.5 dBi at 5.5 GHz. The omni directional radiation pattern for the two operating bands is obtained. The measured bandwidth(S11=-10 dB) are 90 MHz at 2.44 GHz and 1280 MHz at 5.5 GHz respectively

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.5 s.108
• /
• pp.401-407
• /
• 2006

In this paper, we present a small-sized and light weighted dual-band antenna for an access point of 2.4/5 GHz dual-band WLAN(Wireless Local Area Network). The antenna for WLAN should show the characteristic of omni-directional radiation pattern. First, to obtain the omni-directional radiation pattern the proposed dual-band antenna has an orthogonal inverted triangular type element at the center and locates four resonating elements symmetrically around it. Also, for the purpose of easy manufacturing and miniaturization of the antenna, we changed the central element which had the orthogonal inverted triangular type structure into the plate type. Measured $S_{11}$ for the proposed dual-band plate type antenna showed characteristic which was less then -12.8 dB for WLAN frequency bands. Measured results for the maximum gain showed 3.17 dBi at 2.44 GHz, 5.38 dBi at 5.77 GHz with omni-directional radiation pattern. The implemented antennas showed applicable performances for the access point of WLAN.

• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.1112-1115
• /
• 2019

This paper proposes a novel low-profile omni-directional microstrip antenna to mount on the deployable wing of the observation munition. The proposed antenna is designed on seven hexagonal resonators in a quasi-circular array to achieve a monopolar radiation pattern with a thin substrate. By employing the mesh ground structures, the resonant frequencies and impedance bandwidths of the proposed antenna is investigated. To verify the feasibility of the mesh ground structure, the thin ground wire width is investigated theoretically for improving the 3-dB fractional bandwidth, realized antenna gain and quality-factor. The proposed antenna demonstrates a good monopolar radiation in good agreement with the simulation results. The implemented prototype shows the measured bandwidth of 326 MHz with respect to 5.65% centered at 5.77 GHz and realized gain of 5.49 dBi at 5.84 GHz.

• Journal of the Semiconductor & Display Technology
• /
• v.22 no.4
• /
• pp.142-147
• /
• 2023

This paper presents a novel design of a differential patch antenna for 60-GHz millimeter-wave applications. The design process of the back-to-back (BTB) patch antenna is based on the conventional single-patch antenna. The initial design of the BTB patch antenna (Type-I) has a patch size of 0.66 × 0.98 mm² and a substrate size of 0.99 × 1.48 mm². It has a gain of 1.83 dBi and an efficiency of 94.4% with an omni-directional radiation pattern. A 0.4 mm-thick high-resistivity silicon (HRS) is employed for the substrate of the BTB patch antenna. The proposed antenna is further analyzed to investigate the effect of substrate size and resistivity. As the substrate resistivity decreases, the gain and efficiency degrade due to the substrate loss. As the substrate (HRS) size decreases approaching the patch size, the resonant frequency increases with a higher gain and efficiency. The BTB patch antenna has optimal performances when the substrate size matches the patch size on the HRS substrate (Type-II). The antenna is redesigned to have a patch size of 0.81 × 1.18 mm² on the HRS substrate in the same size. It has an efficiency of 94.9% and a gain of 1.97 dBi at the resonant frequency of 60 GHz with an omni-directional radiation pattern. Compared to the initial design of the BTB patch antenna (Type-I), the optimal BTB patch antenna (Type-II) has a slightly higher efficiency and gain with a considerable reduction in antenna area by 34.8%.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.12 no.4
• /
• pp.343-348
• /
• 2019

In this paper, a dual-band antenna is proposed for the autonomous vehicle as well as omni-directional. The proposed antenna operates in the 4G/LTE band (1,710~2,170MHz) and 5G/NR band (3,400~3,700MHz). In order to obtain the dual-band operation, the planar monopole antenna is proposed as the novel structure with single port of the 50ohm. To give the properties of dual-band, an additional antenna element with slit was added to the planar monopole antenna, and then a structural adjustment parameter was optimized for achieving the target performance in bands. The planar monopole antenna in the LTE band acts as the coupled feed for the added parasitic radiator in the 5G NR band. The proposed antenna has $38.5{\times}36.0{\times}1.0[mm^3]$ on a ground with diameter of 96mm. From the fabrication and measurement results, the impedance bandwidth (VSWR<2) of the proposed antenna covers 1,480~2,260MHz (LTE band: 1,710~2,170MHz) and 3,310~3,930MHz (5G NR band: 3,400~3,700MHz). The proposed planar monopole antenna also obtained the measured gain and radiation pattern of omni-directional radiation pattern in the anechoic chamber.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.221-224
• /
• 2005

In this paper, We have designed, fabricated and measured a stacked planar antenna for Ultra-Wideband communication. Radiation parts of the antenna have exponential curve and fed by strip feeding network. We have used the HFSS of Ansoft to simulate the antenna. It was designed to work on a substrate Teflon of thickness 1.575mm and relative permittivity 3.2. The proposed antenna covered the entire UWB band( 3.1GHz $\sim$ 10.6GHz ) for S11$\leq$l0dB. Also the proposed antenna show a good characteristics, linear phase, omni -directional pattern lot UWB applications. Besides the measured results have a reasonable agreement with the simulated results.

• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.1100-1103
• /
• 2019

This paper presents the design method of a planar sleeve monopole antenna on PCB, which has wider bandwidth compared to that of the conventional sleeve monopole antenna, by showing the fact that the sleeve of the conventional antenna can be simplified in structure. The designed and fabricated planar sleeve monopole antenna's structure is very simple, with a monopole adjacent to a small square sleeve on FR4 PCB. The antenna shows 46% wider bandwidth compared to the corresponding 3-dimensional one with nearly omni-directional radiation property.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.2
• /
• pp.249-254
• /
• 2014

We have studied on the possibility of railway stability system using RFID tag. UHF RFID tag was desinged, manufactured and tested. Proposed UHF tag antenna has PIFA type structure and inset feed multi matching technique was attempted for impedance matching of antenna. The impedance bandwidth (VSWR < 3) of the proposed tag antenna covers 917~923 MHz. Measured peak gain is 3.225 dBi and UHF band with an omni-directional radiation pattern. RFID reader and tag installed in motor car and track, respectively. Then, tag recognition rate according to velocity of car (under 45 km/h) represented 100 %.