• Tribology and Lubricants
• /
• 제20권4호
• /
• pp.204-208
• /
• 2004

This paper presents the oil leakage characteristics of the valve stem system in gasoline engines. For the oil leakage investigation, four study models have been prepared as functions of used poppet valve and used valve stem seal, used poppet valve and unused valve stem seal, unused poppet valve and used valve stem seal, and unused poppet valve and unused valve stem seal. With four models, the experimental study on the oil leakage has been investigated for the oil temperature, intake pressure, and camshaft speed. The experimental results show that the sealing performance of the valve stem seal plays an important role on the leakage of the valve stem system. And the appropriate replacement of a stem seal with used poppet valve shows good sealing performance in oil leakage in compared with a new valve system.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 춘계학술대회 논문집
• /
• pp.121-127
• /
• 2012

Whine noise in engine oil pump system was issued in developing an engine. Generally, A noise of engine oil pump largely are classified two cases. The first one is a gearing noise caused by relative motion of inner rotor and outer rotor. The other is fluid pulsation noise caused by oil pressure fluctuation. The aim of the paper is to identify a noise mechanism in engine oil pump and improve its Noise. Also, it suggests to the guide line on the design of oil pump.

• 한국자동차공학회논문집
• /
• 제13권5호
• /
• pp.19-28
• /
• 2005

It is of great economic importance to minimize the cylinder wear and the consumption rate of cylinder oil in a large two-stroke diesel engine. The motor-driven cylinder lubricator was first developed fur a large two-stroke marine diesel engine made in $W{\ddot{a}}rtsil{\ddot{a}}a$ Switzerland Ltd. by the joint research of industry-university. In this study, the effects of revolution speed, plunger stroke and cylinder back pressure on maximum discharge and delivery pressures, delivery delay duration, and oil feed rate are experimentally investigated by the home-manufactured cylinder lubricator. The maximum discharge pressure with a spot of 0.03 m and the maximum loss pressure at spots of 5, 6.78 and i 0 m away from the end of lubricator slot are increased as plunger stroke, revolution speed and back pressure are elevated, and the delivery delay duration is shortened as plunger stroke, revolution speed and oil pipe length are increased. Also, oil feed rate is increased as plunger stroke and revolution speed are raised, but lowered as the back pressure is increased.

• 대한조선학회논문집
• /
• 제33권4호
• /
• pp.22-31
• /
• 1996

임의의 형상을 갖는 몽뚝한 물체에 작용하는 압력을 효율적으로 계산할 수 있는 방법을 확립하여, 조류중 유벽의 부유 성능을 스커트의 변형을 고려해 예측할 수 있는 방법을 개발하였다. 물체 전면의 압력은 반류영역을 박리유선을 경계로한 가상의 강체로 놓고 포텐샬 유동을 해석하여 구하였고, 후면의 압력은 기존의 실험 결과를 바탕으로 결정하였다. 압력 계산 방법의 검증을 위해 몇 가지 뭉뚝한 물체의 무한 수심에서의 압력 저항을 계산하여 기존의 실험 결과와 잘 일치한다는 것을 확인하였다. 유벽의 변형은 유동장과 연계되어 있어서 순차반복법을 통하여 구하였다. 여러 조류속도와 추의 질량에 대한 유벽의 변형된 형상과 홀수의 감소를 구하였다.

• 한국정밀공학회지
• /
• 제30권8호
• /
• pp.839-846
• /
• 2013

Because the performance of a reciprocating compressor in refrigeration and air-conditioning systems is influenced by the lubrication characteristics of sliding components, the lubrication characteristics between the crankshaft and journal bearing have to be researched for the design and the performance improvement of reciprocating compressors. Thus, the proper supply of lubricant for a lubrication between the crankshaft and journal bearing is essential, and an oil path for lubricant supply is installed in the shaft or bearing. However, in order to guarantee the lubrication performance of the journal bearing, it is necessary to design the position of the oil path. Therefore, it is studied to find the optimum position of the oil path by the analysis of the pressure distribution in the journal bearing. The results show that the position of the oil path is significantly influenced by the pressure distribution of the oil film in the journal bearing.

• 한국자동차공학회논문집
• /
• 제24권1호
• /
• pp.90-98
• /
• 2016

Currently government certified test method for an automobile remanufactured products is insufficient. Thus many automotive parts in the remanufacturing market are lacking proper evaluation criteria and production of defective products are causing customer dissatisfaction. In this paper a power steering oil pump, which requires stringent manufacturing standards, is studied by the failure mode and effect analysis approach. The research suggested that the test criteria such as discharge flow characteristic test, tightness test, pulley run-out test, pressure switch operation test, low temperature test and rotation pressure durability test should be performed to evaluate the reliability of remanufactured power steering oil pumps. As a result of tests, the performance of remanufactured power steering oil pump satisfied the evaluation criteria of pressure switch operation test and low temperature test. However, the remanufactured power steering oil pump failed to satisfy the evaluation criteria on discharge performance test, tightness test and pulley run-out test. These performance evaluation tests proved the necessity of standard process for the remanufactured power steering oil pump.

• 한국자동차공학회논문집
• /
• 제19권5호
• /
• pp.51-57
• /
• 2011

Parametric studies based on analysis of lubrication system of a four cylinder gasoline engine are illustrated system in this paper. In development process of engine lubrication system, parts of failure cases are related with oil pull over and oil churning phenomenon. The crankcase & head system pressure by oil churning phenomenon are gradual increased. It cause oil pull over phenomenon at engine breather line and oil over-consumption. In order to improve oil reduction and oil pull over phenomenon are also considered in the developing state. For this study, the characteristics of engine lubrication system are measured at various tilting angle and drain hole sizes. In addition, the oil flow & oil quantity are tested by blow by meter and catch jar. Results are presented to stabilize the oil supply system at sever driving condition. The data from present study are available for the engine lubrication system.

• 오토저널
• /
• 제5권1호
• /
• pp.45-53
• /
• 1983

There exist many kinds of frictions in internal combustion engine such as piston ring and skirt, cam and tappet, bearing friction etc. Among them, the frictions between piston ring, skirt and cylinder are particular. These frictions for motoring test are differ from that of firing test even though the temperature of cooling water and lubricating oil keep identically. The frictions for firing test are increased due to combustion pressure and products. The precise calculation of the friction is difficult. But we can assume that the friction is governed by the viscosity of lubricating oil and gas pressure of cylinder. And the viscosity of lubricating oil is dependant on gas temperature of cylinder, so the piston friction may be governed by gas pressure and temperature of cylinder. In this treatise, we propose the method of evaluating piston friction under the condition of constant engine speed, and we analyzed the behaviours and influence of factors concerned with the piston friction for output correction when the inlet pressure and temperature were varied. The main results are as follows: 1) The behaviours on the inlet conditions for the contact force of the piston rings and the viscosity of the lubricating oil concerned with piston friction are found. 2) The essential point the these behaviours is dependant on the cyclic variation following to the inlet conditions. 3) According to our analysis, It was observed that the viscosity of lubricating oil is more effective than the contact force to the piston rings.

• 설비공학논문집
• /
• 제11권4호
• /
• pp.472-483
• /
• 1999

The evaporation heat transfer and pressure drop characteristics for HFC-l34a in flat plate type heat exchangers with enhanced beads were experimentally investigated. Three plate type evaporators with different geometric condition of U-turn area were tested. Mass fluxes were tested over the range of 83kg/$m^2$s to 166kg/$m^2$s, and heat fluxes were varied from 4㎾/$m^2$ to 12㎾/$m^2$. Evaporation temperature was 5$^{\circ}C$ with inlet qualities of 0.1 to 1.0. There was no notable difference in the heat transfer coefficient by geometric variation of U-turn area, but the third plate with cross-ribbed channel at U-turn area was better than others in the evaluation using volume goodness factor comparison. Also, the mixtures of HFC-l34a and PAG oil was tested to determine oil effects on heat transfer and pressure drop. As oil concentration was increased, heat transfer coefficient was increased by 22~48% up to the 3wt.%, but decreased by 14~22% at the 4wt.%. The pressure drop was increased by the maximum of 100% as oil concentration was increased.

• 한국기계가공학회지
• /
• 제18권1호
• /
• pp.16-23
• /
• 2019

Cooking oil in kitchen-fog is the most harmful factor to the health of a cook. The proposed filter is a tool that protects the cooked state, to prevent users from inhaling oil mist in the kitchen. Due to efficiency issues, existing filters are of the mesh type or baffle type. In this paper, CFD analysis is carried out to select a filter with low pressure loss and low efficiency, and to attach the sub-filter to improve efficiency. The results of the analysis on the collection efficiency and pressure loss of three sub-filters, i.e., circle type, droplet type, and cone type, showed that the collection efficiency was 64.09% and the pressure loss was 1.26 mmAq when the circle type sub-filter was applied. The position of the sub-filter showed the best efficiency and pressure loss when it was located at the bottom of the center of the gap of the main filter.