• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.23 no.4
• /
• pp.36-41
• /
• 2015

The cyclone separator is a simple device, which causes the centrifugal separation of materials such as droplets or particles in a fluid stream. The cyclone separator utilizes the energy obtained from fluid pressure and linear motion to create rotational fluid motion. This rotational motion leads the materials suspended in the fluid to separate from the fluid quickly due to the centrifugal force. The rotation is produced by the tangential or involuted introduction of fluid into the vessel. These materials may be droplets of fuel in blow-by gas through an engine. Droplets suspended in the feed liquid may separate according to size, shape, or density. And the change of part dimension in a cyclone separator can yield the its performance variation. The current study shows the influence of design parameters on the performance of a cyclone separator for blow-by gas.

• Tribology and Lubricants
• /
• v.10 no.1
• /
• pp.69-77
• /
• 1994

Oil flow pass of hermetic scroll compressor with back pressure chamber was described. Dynamic analysis was preceded in order to obtain the loads on the lubricating contacts. The mobility method of dynamically loaded journal bearings was applied to the crank jornal bearing and lower main bearing, and they could be designed to operate under fluid film lubrication. From the consideration of their film thicknesses and oil flow rates, optimal bearing clearances or other bearing dimensions could be assessed. The major friction loss was calculated to be from the axial force between the two scrolls. Therefore, it was suggested that the designers should be careful to reduce the over-turning moment on the orbiting scroll.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.1
• /
• pp.284-294
• /
• 1996

In this paper, dynamic characteristics of an AT clutch system were investigated considering the dynamics of check ball and hydraulic control valves. Dynamic model of a pressure control solenoid valve (PCSV) was obtained by Bondgraph and permeance method. Also, the clutch piston and check ball dynamics were modeled by considering the effect of centrifugal force of the oil entrapped in the clutch chamber. In order to validate the dynamic models obtained, plunger displacement of PCSV and pressure response of the clutch supply lines were compared with the available experimental data, which were in good accordance with the numerical results. Using the dynamic model of the clutch system, simulations were performed to investigate the effect of the rotational speed on the response of clutch cylinder pressure, clutch piston and check ball displacement, and oil flow rate into the cylinder and flow rate out of the check valve.

• Journal of Aerospace System Engineering
• /
• v.17 no.5
• /
• pp.11-18
• /
• 2023

The architecture of the Fuel Thermal Management System (FTMS) in a commercial aircraft engine was built to model and simulate the fuel system. The study shows the thermal interactions between the fuel and engine lubrication oil through the mission profile of a high bypass ratio, two-spool turbofan engine. Fuel temperature was monitored as it flowed through each sub-component of the fuel system during the mission. The heat load in the fuel system strongly depended on the fuel flow rate, and was significantly increased for the periods of cruise and descent with decrease of fuel flow rate, rather than for the periods of take-off. Due to the thermal interaction in the pump housing, the fuel temperature at the outlet of the low-pressure pump was increased (4.0, 9.2, and 30.0) % over the case without thermal interaction for take-off, cruise, and descent, respectively.

• Korean Chemical Engineering Research
• /
• v.55 no.2
• /
• pp.201-213
• /
• 2017

Water is removed from crude oil containing water by using oil separator. This study aims to develop a three-dimensional (3D) Eulerian computational fluid dynamics (CFD) model to predict the separation efficiency of air-water-oil separator. In the incompressible, isothermal and unsteady-state CFD model, air is defined as continuous phase, and water and oil are given as dispersed phase. The momentum equation includes the drag force, lift force and resistance force of porous media. The standard k-${\varepsilon}$ model is used for turbulence flow. The exit pressures of water and oil play an important role in determining the liquid level of the oil separator. The exit pressures were identified to be 6.3 kPa and 5.1 kPa for water and oil, respectively, to keep a liquid level of 25 cm at a normal operating condition. The time evolution of volume fractions of air, water and oil was investigated. The settling velocities of water and oil along the longitudinal separator distance were analyzed, when the oil separator reached a steady-state. The oil separation efficiency obtained from the CFD model was 99.85%, which agreed well with experimental data. The relatively simple CFD model can be used for the modification of oil separator structure and finding optimal operating conditions.

• 한국연소학회:학술대회논문집
• /
• 2004.06a
• /
• pp.207-214
• /
• 2004

Extra heavy vacuum residue oil has advantage as the fuel of a power plant in reducing the cost of power generation. Numerical study is conducted by the KIVA code to understand combustion, heat transfer and flow field characteristics in the test reactor. The combustion model of pulverized coal particles is adopted as the combustion process of extra heavy oil is similar to that of coal. As an initial phase of investigation parametric study is performed with respect to SMD and spray angle of injected spray droplets.

• Proceeding of EDISON Challenge
• /
• 2014.03a
• /
• pp.556-561
• /
• 2014

본 연구에서는 유조선 공법의 유체역학적 타당성을 검증하고자 한다. EDISON_CFD를 이용하여 간단화한 서산 간월호의 간척 이전 모습을 모델링하였다. 방조제 모델에서의 난류 유동을 방조제 사이에서의 유속과 사이에서 받는 압력의 분포를 통해 유조선 공법이 실제로 방조제 건설에 도움이 될 수 있는지에 대해 평가했다.

• KSBB Journal
• /
• v.20 no.1 s.90
• /
• pp.12-17
• /
• 2005

Despite a wide range of fatty acids in fish oil, its the usage are very limited owing to off-flavors and volatile compounds in the oil. A way to extract and remove volatile compounds was performed at a semi-flow extractor by using supercritical carbon dioxide $(SC-CO_2)$. Samples of the oil were treated at the conditions which ranged from $30\;to\;80^{\circ}C$ and from 80 to 200 bar with 10 mL/min flow rate of carbon dioxide. In the oil the volatile compounds were analyzed by gas chromatography. Before extraction with $SC-CO_2$ the oil sample was detected over 129 peaks but 99 compounds were identified. The results demonstrated that at $40^{\circ}C$ and 200 bar extraction condition the volatile compounds in the tuna fish oil were removed, except for 14 compounds identified after extraction and other $SC-CO_2$ extraction conditions reached to high reduction of the volatile compounds.

• The KSFM Journal of Fluid Machinery
• /
• v.3 no.1 s.6
• /
• pp.28-36
• /
• 2000

For the improvement of the pump characteristics in the partial capacity range, it must be verified that the influence of the impeller design factor on the internal flows and the influence of the impeller internal flows on the pump characteristics. In this paper, in order to understand the influence of outlet angles on flow conditions and characteristics of a mixed flow pump, experiments were carried out for four kinds of impeller, which have the same inlet angle distributions and meridional section shapes. Results shown that separation and stall in the partial capacity range were enlarged by the outlet angles. The relationship between the separation and the stall at the impeller and the discharge flow conditions were clarified.

• Journal of the Korean Society of Visualization
• /
• v.8 no.3
• /
• pp.12-21
• /
• 2010

Swirling flows are found in very wide range of applications, for examples, cyclone separators, spraying machines, heat exchangers and jet pumps, ect. Relatively, little work has been done on the swirl flow using flow visualization techniques. This study deals with many visualization techniques to study on swirling flow. These techniques are related to oil films methods, smoke, dye liquids, liquid crystal, stroboscope light, smoke wire, white light, naphthalene sublimation, LDV(lase doppler Velocimetry) and PIV(particle image velocimetry). The present work has handled single, annular, carved tube, swirl expansion and swirl wake using several visualization methods in the vertical and horizontal circular tube.