• 한국정밀공학회지
• /
• 제22권7호
• /
• pp.122-129
• /
• 2005

Shoe with leather upper such as safety and golf shoe requires a roughing process where the upper is roughed fur helping outsole to be cemented well. It is an important and basic process for production of leather shoe but is not automated yet. Thus, there are problems that the defect rate is high and the quality of roughed surface is not uniform. In order to solve such problems, the interest in automation of roughing process is being increased and this paper introduces CAM system for 5-axis automatic roughing machine as one part of automation of roughing process. The CAM system developed interpolates a B-spline curve using points measured from the Roughing Path Measurement System. The B-spline curve is used to generate the tool path and orientation data fer a roughing tool which has not only stiffness but also flexibility to rough the inclined surface efficiently. For productivity, the upper of shoe is machined by side of the roughing tool and tool offset is applied to the roughing tool for machining of inclined surface. The generated NC code was applied to 5-axis polishing machine for the test. The upper of shoe was roughed well along the roughing path data from CAM and the roughed surface was proper fur cementing of the outsole.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.51-56
• /
• 2011

The train travels on the track and, thus, the rear wheels precisely follow the paths of the front wheels. On the contrary, in the vehicles running on the road like automobiles, buses and trucks, the front wheels try to drag the rear ones toward them and across the inside of the curve. Off-tracking is defined as the radial offset between the path of the centerline of the front axle and the path of the centerline of the following axle. In the case of the bimodal tram with AWS(all wheel steering), the off-tracking decrease but the rear swing-out values increase because of the rear steering at the reverse phase angle. Thus, in order to determine the swept path width, maximum road width at the minimum turning radius, off-tracking and swing-out should be considered for the bimodal tram. In this paper, trajectory simulations were carried out for the various condition such as front steering, front and rear steering and suppression of swing-out to optimize the swept path width.

• 대한전기학회논문지
• /
• 제41권9호
• /
• pp.953-959
• /
• 1992

As the TC(time-current) curve corresponding to symmetrical time invariant RMS value has been traditionally chosen and used for setting the relay, it has caused the misoperation errors on relay coordination because of CT secondary current being actually an asymmetrical time varying RMS value. In this paper, an algorithm for calculating the relay operating time is developed to study the asymmetrical effect using the step-by-step method. We represent the relay operating time errors between with and without DC offset versus PSM(plug setting multiplier), TMS(time multiplier setting) and X/R ratio. And also we present the correction factor. Finally we confirm the validity of this technique through the case study.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.398-401
• /
• 2001

This paper presents rough cutting pat고 drilling. This method has differences from conventional method which uses boundary curve by intersecting object to machine and each cutting plane. Die-cavity shape is drilled in z-map, we select various tool and remove much material in the short time. as a result, this method raise productivity. The major challenges in die-cavity pocketing include : 1)finding an inscribed circle for removing material of unmachined regions, 2) selecting optimal tool and efficiently arranging tool, 3) generating offset surface of shape, 4) determining machined width according to the selected tool, 5) detecting and removing unmachined regions, and 6) linking PJE(path-joining element). Conventional machining method calling contour-map is compared with drilling method using Z-map, for finding efficiency in the view of productivity.

• Steel and Composite Structures
• /
• 제29권2호
• /
• pp.161-173
• /
• 2018

Point bending is often used for cambering and curving structural steel girders. An analytical solution, applicable in the elasto-plastic range only, that relates applied loads to the desired curve was recently developed for inducing horizontal curves using four-point bending. This solution does not account for initial residual stresses and geometric imperfections built-in hot-rolled sections. This paper presents results from a full-scale test on a hot-rolled steel section curved using four-point bending. In parallel, a numerical analysis, accounting for both initial geometric imperfections and initial residual stresses, was carried out. The models were validated against the experimental results and a good agreement for lateral offset and for strain in the elasto-plastic and post-plastic ranges was achieved. The results show that the effect of initial residual stresses on deformation and strain is minimal. Finally, residual stresses due to cold bending calculated from the numerical analysis were assessed and a revised stress value for the service load design of the curved girder is proposed.

• 한국정밀공학회지
• /
• 제23권9호
• /
• pp.190-199
• /
• 2006

A new approach which combines implicit surface scheme and recursive subdivision method is suggested in order to fill the holes with complex shapes in the polygon model. In the method, a base surface is constructed by creating smooth implicit surface from the points selected in the neighborhood of holes. In order to assure C$^1$ continuity between the newly generated surface and the original polygon model, offset points of same number as the selected points are used as the augmented constraint conditions in the calculation of implicit surface. In this paper the well-known recursive subdivision method is used in order to generate the triangular net with good quality using the hole boundary curve and generated base implicit surface. An efficient anisotropic smoothing algorithm is introduced to eliminate the unwanted noise data and improve the quality of polygon model. The effectiveness and validity of the proposed method are demonstrated by performing numerical experiments for the various types of holes and polygon model.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 Ⅳ
• /
• pp.2467-2470
• /
• 2003

This paper presents a new structure of MPEG-4 AAC encoder. The proposed encoder directly shapes quantization noise distribution according to the energy distribution curve and thereafter performs adjustment of the offset level of the noise distribution to meet the given bit rate. The direct noise shaping and the bit rate matching scheme of the proposed encoder algorithm significantly alleviate the problem of conventional encoder's processing burden related with the employment of the precise psychoacoustic model and iteration intensive quantizer. The encoder algorithm is implemented on ARM processor with fixed-feint arithmetic operations. The audio quality of the implemented system is observed comparable to those of commercially available encoders, white the complexity of the implementation is drastically reduced in comparison to the conventional encoder systems.

• 산업기술연구
• /
• 제15권
• /
• pp.23-32
• /
• 1995

The methodology of automatic generation of tool path for rough cutting of a sculptured surface is proposed with the improved contouring method, unequal level line machining. Considering the surface shape and the diameter of the endmill, the distance between level lines is obtained. To improve MMR, initial rough cutting is processed with the large diameter endmill and the remained material is removed by the relatively small diameter endmill. Tool path is generated from the offset curve of respective level line and the interferences between the tool and workpiece are automatically avoided. After generating NC part program, the sculptured surface is machined at the vertical machining center. From the experimental results, total cutting length and machining time are reduced more effectively than conventional contouring methods.

• 한국인쇄학회지
• /
• 제25권1호
• /
• pp.43-52
• /
• 2007

Offset printing is one of the well known printing technique of lithographic process and consists of image area and 'non-image area on a flat image carrier. The surface tension of dampening water can be controlled by adding IPA after mixing of raw water and etching solution. The etching solution contains a surfactant for reducing surface energy, a clean agent for non-imaging area, wetting agent for protecting non-imaging area from oil components like ink and also an emulsifying agent for controlling emulsification. In this study, the present situation of dampening water maintenance has examined by collecting dampening water using at domestic companies. The pH related to dampening water, conductivity, contact angle, emulsification curve are measured to define the current situation of dampening water control of each companies and to analyze the relationship among measured properties. In the study most of companies among 16 printing companies tested controlling dampening water through pH value. However, the quality of printing has varied depending upon conductivity, contact angle, IPA content, and emulsification value. The control of dampening water should be carry at the state of the standard when adding proper ratio of etching solution. It would be more effective when pH or conductivity control carries out in parallel with controlling dampening water. Therefore the concept that pH5.5 is correct is based concept. Based on these initial tests it is defined that the standardization of dampening water control is required.

• Journal of the Korean Wood Science and Technology
• /
• 제45권6호
• /
• pp.728-736
• /
• 2017

In this study, the bending behavior of cross-laminated timber (CLT) connected by nails were investigated. Especially, the load-carrying capacity of the nail-jointed CLT under out-of-plane bending was predicted by the lateral resistance of the used nails. Three-layer nail-jointed CLT specimens and a nail connection were manufactured by 30 mm (thickness) ${\times}$ 100 mm (width) domestic species (Pinus koraiensis) laminas and Ø$3.15{\times}82mm$ nails using a nail-gun. Shear test for evaluating the nail lateral resistance and bending test for evaluating the load-carrying capacity of the nail-jointed CLT under out-of-plane bending were carried out. As a result, two lateral resistance of the used nail, the 5% fastener offset value and the maximum value, were 913 N and 1,534 N, respectively. The predicted load-carrying capacity of the nail-jointed CLT by the 5% offset nail lateral resistance was similar to the yield points on the actual load-displacement curve of the nail-jointed CLT specimens. Meanwhile, the nail-jointed CLT specimens were not failed until the tension failure of the bottom laminas occurred beyond the maximum lateral resistance of the nails. Thus, the measured maximum load carrying capacities of the nail-jointed CLT specimens, approximately 12,865 N, were higher than the predicted values, 7,986 N, by the maximum nail lateral resistance. This indicates that the predicted load-carrying capacity can be used for designing a structural unit such as floor, wall and roof able to support vertical loads in a viewpoint of predicting the actual capacities more safely.