• The KSFM Journal of Fluid Machinery
• /
• v.19 no.6
• /
• pp.34-42
• /
• 2016

The organic Rankine cycle (ORC) has been used to convert thermal energy to mechanical energy or electricity. The available thermal energy could be waste heat, solar energy, geothermal energy, and so on. However, these kinds of thermal energies cannot be provided continuously. Hence, the ORC can be operated at the off-design point. In this case, the performance of the ORC could be worse because the components of the ORC system designed based on a design point can be mismatched with the output power obtained at the off-design point. In order to improve the performance at the off-design point, a few components were replaced including generator, bearing, load bank, shaft, pump and so on. Experiments were performed on the same facility without including other losses in the experiment. The experimental results were compared with the results obtained with the previous model, and they showed that the system efficiency of the ORC was greatly affected by the losses occurred on the components.

• Journal of Adhesion and Interface
• /
• v.7 no.4
• /
• pp.13-17
• /
• 2006

The elasto-plastic finite element method (FEM) was used to investigate the effect of off-center recessing location (8 mm length) on the stress distribution in the lap zone of adhesively bonded aluminium double lap joint. The results from simulation showed that the effect of off-cent recessing in bondline of double lap joint in the mid-bondline is not evidently to stress distribution in mid-bondline but the peak stresses both in mid-bondline and in the interface near the adherend side of the joint may increase markedly when an 8 mm length recessing was arranged symmetrical to the point of x =18 mm. When shifting an 8 mm length recess from near left end to the right end of the lap zone, all the highest peak stresses in the mid-bondline occurred under the condition of recess arranged symmetrical to the point of x = 6 mm.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.46 no.5
• /
• pp.649-652
• /
• 2013

Distribution and migration of larval and juvenile sandfish Arctoscopus japonicus in the coastal waters off Gangwondo were determined monthly from samples collected by a rectangular bottom net in the coastal waters off Gangwondo from March to July, 2011. Fish were collected in abundance from the northern waters from March to June. The average total length (${\pm}SD$) was $11.5{\pm}1.6$ mm in March increased up to $53.5{\pm}3.3$ mm in June. The size distribution of sandfish by depth suggested that the fish grew waters less than 50 m deep until June, before moving deeper waters of around 100 m.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.6
• /
• pp.50-58
• /
• 2009

Micro laser fabrication techniques can potentially be used for the manufacture of microstructures on the thin flat surfaces with large diameter that are frequently used in semiconductor industries. However, the large size of wafers can cause the degraded machining accuracy of the surface because it can be tilted or distorted by geometric errors of machines or the holding fixtures, etc. To overcome these errors the off-line focusing error compensation method is proposed. By using confocal autofocus system, the focusing error profile of machined surface is measured along the pre-determined path and can be compensated at the next machining process by making the corrected motion trajectories. The experimental results for silicon wafers and invar flat surfaces show that the proposed method can compensate the focusing error within the level of below $6.9{\mu}m$ that is the depth of focus required for the laser micromachining process.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.493-493
• /
• 2000

Multi-valued decision making for transitional stochastic events was newly derived based on conditional probability of database. The two values (on-off) decision making method without transition had been proposed by one of the author in a previous work for a purpose of realizing human on-off decision making. The current method is an extension of the previous on-off decision making. By combining the conditional probability and the transitional probability, the closed form of the algorithm for the multi-valued transitional decision making was derived. The proposed multi-valued decision making was successfully applied to the determination of the five levels of the vigilance of a subject during the EEG recording; awake stage, drowsy stage and sleeping stages (stage 1, stage 2/3, REM (rapid eye movement)). The method for determining the vigilance level can be directly usable for the two purposes; selection of awake EEG segments for automatic EEG interpretation, and determination of sleep stages through sleep EEG. The proposed multi-valued decision making with a mathematical background of the probability can be applicable widely, in industries and in medical fields for purposes of the multi-valued decision making.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.415-415
• /
• 2012

ZnO nanostructures were synthesized by a vapor phase transport process in a single-zone furnace within a horizontal quartz tube with an inner diameter of 38 mm and a length of 485 mm. The ZnO nanostructures were grown on Au-catalyzed Si(100) substrates by using a mixture of zinc oxide and graphite powders. The growth of ZnO nanostructures was conducted at $800^{\circ}C$ for 30 min. High-purity Ar and $O_2$ gases were pushed through the quartz tube during the process at a flow rate of 100 and 10 sccm, respectively. The sequence of ON/OFF cycles of the Ar gas flow was repeated, while the $O_2$ flow is kept constant during the growth time. The Ar gas flow was ON for 1 min/cycle and that was OFF for 2 min/cycle. The structure and optical properties of the ZnO nanostructures were investigated by field-emission scanning electron microscope, X-ray diffraction, temperature-dependent photoluminescence. The preferred orientation of the ZnO nanostructures was along c-axis with hexagonal wurtzite structure.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1526-1529
• /
• 1994

In hydro-generator, a groundwall insulation of stator windings gradually deteriorates due to mechanical, thermal, electrical and environmental stresses. These stresses combine to result in loose windings, delamination of the stator insulation and/or electrical tracking of the end winding, all of which can lead to stator insulation failures. Conventionally, off-line tests such as partial discharge measurement, DC/AC current test and ${\Delta}tan{\delta}$ test has been used for estimation of winding condition. However, off-line test requires large power supply and generator outage. In addition, major cause of insulation problems such as loose wedges and slot discharges may not be found with off-line diagnoses. This paper describes the on-line partial discharge measurement techniques in the generator stator windings. The experimental results from the UIAM #1 hydro-generator confirms a optimistic application of on-line generator diagnosis method as a reliable tool for evaluation of winding condition.

• Progress in Superconductivity and Cryogenics
• /
• v.25 no.4
• /
• pp.65-69
• /
• 2023

Hydrogen is an eco-friendly energy source and is being actively researched in various fields around the world, including mobility and aerospace. In order to effectively utilize hydrogen energy, it should be used in a liquid state with high energy storage density, but when hydrogen is stored in a liquid state, BOG (boil-off gas) is generated due to the temperature difference with the atmosphere. This should be re-condensed when considering storage efficiency and economy. In particular, large-capacity liquid hydrogen storage tank is required a gaseous helium circulation cooling system that cools by circulating cryogenic refrigerant due to the increase in heat intrusion from external air as the heat transfer area increases and the wide distribution of the gas layer inside the tank. In order to effectively apply the system, thermo-hydraulic analysis through process analysis is required. In this study, the condenser design and system characteristics of a gaseous helium circulation cooling system for BOG recondensation of a liquefied hydrogen storage tank were compared.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.1
• /
• pp.62-72
• /
• 1997

High flexibility and productivity using industrial robots are being achieved in manufacturing lines with off-line robot programmings. A good off-line programming system should have functions of robot modelling, trajectory planning, graphical teach-in, kinematic and dynamic simulations. Simulated results, however, can hardly be applied to on-line tasks until any calibration procedure is accompained. This paper proposes a visual calibration scheme in order to provide a calibration tool for our own off-line programming system of SCARA robots. The suggested scheme is based on the position-based visual servoings, and the perspective projection. The scheme requires only one camera as it uses saved kinematic data for three-dimensional visual calibration. Predicted images are generated and then compared with camera images for updating positions and orientations of objects. The scheme is simple and effective enough to be used in real time robot programming.

• Journal of the Semiconductor & Display Technology
• /
• v.9 no.1
• /
• pp.17-21
• /
• 2010

Currently miniaturized electron-optical columns find their way into electron beam lithography systems. For better lithography process, it is required to make smaller spot size and longer working distance. But, the micro-columns of the multi-beam lithography system suffer from chromatic and spherical aberration, even when the electron beam is exactly on the symmetric axis of the micro-column. The off-axis error of the electron emitting source is expected to become worse with increasing off-axis distance of the focusing spot. Especially the electron beams far from the system optical axis have a non-negligible asymmetric intensity distribution in the micro-column. In this paper, the effect of the off-axis e-beam source is analyzed. To analyze this effect is to introduce a micro-column model of which the e-beam emitting source is aligned with the center of the electron beam by shifting them perpendicular to the system optical axis. The presented solution can be used to analysis the performance of the multi-electron-beam system. The performance parameters, such as the working distances and the focusing position are obtained by the computational simulations as a function of the off-axis distance of the emitting source.