• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.82.3-82
• /
• 2001

This work presents a design technique for the implementation of the liquid level control system by based on the use of a single-chip microcontroller. The proposed model system offers the following attractive features : (1) application of the pressure transducer for sensing the height of liquid in tank (2) using the obtained liquid level for defining on-off condition of the water pump (3) the liquid values were controlled by using stepping motors for controlling of 57 points (4) can set up by using manual control or automatic control (5) can monitor and display the process status either on microcontroller-based control board or on the computer via RS232 serial-port. Experimental results have been employed to show the effectiveness ...

• 반도체디스플레이기술학회지
• /
• 제18권2호
• /
• pp.17-22
• /
• 2019

The method of electrical discharge machining (EDM), one of the processing methods based on non-traditional manufacturing procedures, is gaining increased popularity, since it does not require cutting tools and allows machining involving hard, brittle, thin and complex geometry. This present investigation details the determination of optimum process parameter to attain the better machining performance in EDM of AISI 4340 steel with graphite as a tool electrode. The experimental combinations are planned and analyzed by Taguchi's design of experiments approach. To predict the optimal condition, the experiments are conducted by using Taguchi's L27 orthogonal array. The influence of process variables such as discharge current, pulse on and pulse off time, voltage and spark speed were investigated to control the various desired performance measures such as surface roughness. Analysis of Variance (ANOVA) has to be performed to know the magnitude of each factor. Investigations indicate that the surface roughness is strongly depend on pulsed current.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.371.1-371
• /
• 2002

At lift-off, the jet noise of launch vehicle produces a severe acoustic environment and the loads induced by the acoustic pressure may be damaging to paylaod and equipments. Prediction of the acoustic environment is needed to support the design and test-qualification of components. Currently, such a high frequency problem is usually dealt with by using the SEA, of which the assumptions match reasonably well with the vibro-acoustic condition of system. (omitted)

• 한국전산유체공학회지
• /
• 제13권4호
• /
• pp.72-79
• /
• 2008

This study is to investigate the air flow around a sirocco fan which is used in a range hood. The main object of the study is to improve the flow rate of the fan by analysis of unsteady 3-dimensional incompressible flow. Overall analysis is carried out using CFD method. For this, we used a commercial code, SC/Tetra, and used a sliding mesh method to give the same condition as an actual state. First, verification of the CFD results is done by comparing the experimental data with the numerical data for the suction flow rate. It is confirmed that two results are well consistent. Then for the improvent of flow rate, the effect of shape factors such as diameter ratio of fan, geometry of case, cut-off aperture and guide angle of case exit on the suction flow rate was considered. Especially, for a new design of housing, the principle of Archimedes spiral was used. The overall analysis was applied to a new design of housing, and the result showed an increase of flow rate by 10.7%.

• 해양환경안전학회지
• /
• 제1권1호
• /
• pp.9-25
• /
• 1995

Although the studies carried out in recent years have provied much new information about channel widths and alignment, they are not consistent in their results. In addition, as a result of variations in local condition and type of traffic accommodated, the dimensions of the channel widths vary over a wide range. Therefore, the recommendation made by the maritime engineering organizations over the world, do not offer detailed and decisive optimal design criteria and are all different. It, therefore, was attempted in this paper to draw a decisive guideline on the optimal widths and alignment of the navigational channels, which can be utilized by the port designers at the stage of the planning. The guideline was drawn through the comparison and analysis of the existing guidelines of the U.S.A, Japan and PIANC and simulation experiment. The simulation experiment was carried out using the "Off Line Port and Waterway Design Simulator" to find the optimal dimensions of the widths of the navigational channels. 90 different simulation runs were conducted at the 3 different secenario channels. New guidelines, the result of the study, is expected to be used usefully by the Korean port designers when designing the rapodly developing ports in Korea. in Korea.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.946-949
• /
• 2001

This paper proposes a new zero-current switching (ZCS) pulse-width modulation (PWM) switch cell that has no additional conduction loss of the main switch. In this cell, the main switch and the auxiliary switch turn on and turn off under zero current condition. The diodes commutate softly and the reverse recovery problems are alleviated. The conduction loss and the current stress of the main switch are minimized, since the resonating current for the soft switching does not flow through the main switch. Based on the proposed ZCS PWM switch cell, a new family of dc to dc PWM converters is derived. The new family of ZCS PWM converters is suitable for the high power applications employing IGBTs. Among the new family of dc to dc PWM converters, a boost converter was taken as an example and has been analyzed. Design guidelines with a design example are described and verified by experimental results from the 2.5 kW prototype boost converter operating at 40kHz.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2006년도 제27회 추계학술대회논문집
• /
• pp.331-335
• /
• 2006

초음속 흡입구는 안정한 유동은 설계점에서 얻을 수 있지만, 비행 중 나타나는 비설계점에서는 흔히 버즈라고 불리는 공력 불안정성에 직면하게 된다. 버즈가 일어나는 동안, 흡입구는 흡입구 선단에 큰 충격파 진동이 나타나며 그에 따라 후류에는 압력 섭동이 발생하며 이는 엔진의 성능감소를 야기한다. 본 연구는 버즈의 일반적인 특성을 파악하기 위해 1단 꺽임각을 갖는 외부 압축식 축대칭 흡입구를 이용하여 실험적, 수치적 연구가 수행되었다. 본 연구를 통해 간헐적으로 나타나는 버즈를 관찰할 수 있었고 배압이 증가할수록 버즈가 일어나는 주파수가 커짐을 확인할 수 있었다.

• 한국유체기계학회 논문집
• /
• 제12권5호
• /
• pp.39-46
• /
• 2009

This paper outlines how the on-line performance monitoring system can be used to improve the efficiency and maintenance of the equipments. And a method of the heat rate allocation to each equipment was suggested to monitor the performance of combined cycle power plants. This calculates the expected heat rate of current conditions and compares it with actual values. Loss allocation in heat rate is reconciled by calculating the magnitude of the deficiency contributed by major components, such as the gas turbine, heat recovery steam generator, steam turbine and condenser. Expected power output is determined by a detailed model and correction curves of the plant. This simulation models are found to reproduce high accuracy in behavior of the cycle for various operating conditions, both in design and in off-design condition. Errors are lower than 2% in most cases.

• 대한기계학회논문집B
• /
• 제22권3호
• /
• pp.326-335
• /
• 1998

In this study, a steady three-dimensional incompressible turbulent flow within a torque converter was numerically analyzed with the introduction of interrow mixing model. Mixing planes were introduced to exchange the flow informations between two adjacent elements of the torque converter. The mixing planes were installed among three elements of the torque converter. Therefore, in the present method, it could be possible to calculate the flow-filed within the torque converter without any assumption of circulating flow rates or any extension of boundaries toward the upstream and the downstream for each element. The numerically calculated performances of the torque converter were in good agreement with experimental results, and the complex flow patterns were be observed according to design and off-design condition. As a conclusion, it was found that the present numerical method was very effective in the steady flow analysis of torque converters.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 춘계학술대회논문집; 경주코오롱호텔; 22-23 May 1997
• /
• pp.413-417
• /
• 1997

Distributed piezoelectric sensor and actuator have been designed for efficient vibration control of a cantilevered beam. Both PZT and PVDF are used in this study, the former as an actuator and the latter as a sensor for our integrated structure. For the PZT actuator, the position and size have been optimized. Optimal electrode shape of the PVDF sensor has been determined. For multi-mode vibration control, we have used two PZT actuators and a PVDF sensor. Electrode shading of PVDF is more powerful for modal force adjustment than the sizing and positioning of PZT. Finite element method is used to model the structure that includes the PZT actuator and the PVDF sensor. By deciding on or off of each PZT segment, the length and the location of the PZT actuator are optimize. Considering both of the host structure and the optimized actuators, it is designed that the active electrode width of PVDF sensor along the span of the beam. Actuator design is based on the criterion of minimizing the system energy in the control modes under a given initial condition. Sensor is designed to minimize the observation spill-over. Modal control forces for the residual(uncontrolled) modes have been minimized during the sensor design. Genetic algorithm, which is suitable for this kind of discrete problems, has been utilized for optimization. Discrete LQG control law has been applied to the integrated structure for real time vibration control. Performance of the sensor, the actuator, and the integrated smart structure has been demonstrated by experiments.