• International Journal of Fluid Machinery and Systems
• /
• v.10 no.3
• /
• pp.218-226
• /
• 2017

Severe radial thrust under off-design operating conditions can be a harmful factor for centrifugal pumps. In the present work, effects of geometry of a double volute casing on the hydrodynamic performance of a centrifugal pump have been investigated focusing on off-design conditions. Three-dimensional steady Reynolds-averaged Navier-Stokes analysis was carried out by using shear stress transport turbulence model. Numerical results for the hydrodynamic performance of the centrifugal pump were validated compared with experimental data. The hydraulic efficiency and radial thrust coefficient were used as performance parameters to evaluate the hydrodynamic characteristics of the centrifugal pump. The cross-sectional area ratio of the volute casing, the expansion coefficient of the rib structure, the distance between the rib starting point and volute entrance, and radius and width of the volute entrance, and length of the rib structure, were selected as geometric parameters. Results of the parametric study show that the performance parameters are significantly affected by the geometric variables and operating conditions. Optimal configurations of the double volute casing based on the design of experiments technique show outstanding performance in terms of the efficiency and radial thrust coefficient.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.13 no.5
• /
• pp.57-63
• /
• 2009

A modeling and simulation program for an environmental control system (ECS) of a pod installed under wings of an aircraft was developed in order to estimate the system‘s performance during a flight. First, through the system configuration analysis in the main operational condition of the aircraft system, an ECS configuration adopting an air cycle machine (ACM) was selected. Therefore the modeling program was developed to simulate the ECS with an ACM. Second, the sensitivity analyses on performance variation of main components were conducted to complete the conceptual design of the ECS. A design point for the system and its components was obtained through the analysis with the modeling and simulation program. The design point for the system and components was obtained through the analysis with the modeling and simulation program. Third, in order to study the feasibility of the ECS configuration, off-design performances of the ECS on various flight conditions, such as take off, maneuver, cruise and landing etc were estimated. Dynamic characteristics were analyzed by transient performance evaluations.

• Journal of Korean Society of Transportation
• /
• v.26 no.4
• /
• pp.7-16
• /
• 2008

Severe congestion is happening at urban freeway off-ramps in Seoul. Major causes of congestion at off-ramps are a shortage of capacity and inefficient signal operations at the downstream intersection at off-ramps. It is necessary to control congestion by improving design or operations in the downstream intersection. In this study, the authors analyzed the case of the Jungdong interchange that was improved for design in the downstream intersection. When a freeway and an arterial road cross, diamond interchanges are usually selected with a single-point urban interchange (SPUI) as an alternative. To compare the effectiveness of a diamond interchange with a SPUI, the authors applied these two configurations to the Jungdong interchange using a simulation. The result of the analysis shows that congestion at off-ramps in diamond interchanges can be reduced by improving signal operations such as the application of "4 phase with overlaps" and that diamond interchanges are more efficient than a SPUI with a frontage road. Efficient operation of the downstream intersection by these findings can minimize congestion of not only the downstream intersection but also the freeway mainline.

• Archives of design research
• /
• v.2 no.1
• /
• pp.107-115
• /
• 1989

In my previous research (1986), I considered a general characteristics of a visual image of products. There were really many difficulties in designing all kinds of needs in compliance with the all of their requests in order to satisfy consumers. In addition, under the characteristics of goods, the consumers seem to choose an opti$$\mu$ com\ulcornerbinations after considering the combinations of trade-off. Therefore, this study that selected a watch as an object on this study was analyzed a Design Assessment Structure under the trade-off. As a result of this research: First, an effect of a negative superiority appeared under the trade-off condition among ifems when consumers purchased products. Second, these four items were extracted from the eight items which were suggested in this study through an analysis of factors. Third, the three courses were conformed when a consumer purchased a watch. Fourth, in the all kinds of goods, the price which was considered as an important point was not important item ina relation to a purchasing behavior. According to the concomitant effects, we figured out these four items, that is, form, thickness, readability and wearing and its have to be considered a lot when designing a watch.

• Progress in Superconductivity and Cryogenics
• /
• v.8 no.4
• /
• pp.34-38
• /
• 2006

Cycle analysis was performed in order to find the optimum design point of the LNG Boil-off gas re-liquefaction system. Thermodynamic analysis revealed the system could be defined by three state variables. Thus the system performance could be described by the three cold endpoint temperatures of the three-pass heat exchanger. This enabled us to investigate the cycle performance in terms of the heat exchanger parameters. To get access to the cycle states of higher system performances, larger heat exchangers were found necessary. Also the thermal pinch in cryogenic heat exchangers was found to act as a limiting factor to the system performance.

• Journal of the Korea Furniture Society
• /
• v.18 no.4
• /
• pp.337-344
• /
• 2007

This study explored contemporary furniture theory and practice in Postmodernism mentioned as one of a kind furniture based on ideas from the tradition since Modernism. Qualitative conceptual analysis as the principal methodology was used to explore the postmodern furniture adopting or reflecting ornament from the tradition presented as postmodern furniture designers' point of view differently and variously. Thus, the examples about one of a kind or one-off furniture were dealt with Postmodern ideas appeared in the doubt over Modernism, Post-Modern furniture ideas from the traditional and Modern architecture, ornamental ism, Postmodern theorists, Postmodern furniture and the criteria. As a result, although one of a kind furniture design appealed newly from and based on the ornament of the tradition has been identified as new design like one of a kind furniture which shows lack of function, the piece with the meaningful ornament makes people happier in their daily life. Hence, one of a kind furniture, a work of art, has been required as striking a balance both function or comfort and aesthetics or beauty which makes the people more enjoyable.

• Journal of computational fluids engineering
• /
• v.5 no.2
• /
• pp.38-46
• /
• 2000

It has been indicated that the rotor/stator interaction has distinct causes of unsteadiness, such as the viscous vortex shedding, wake/stator interaction and potential rotor/stator interaction. In this paper, the mechanism of unsteady potential interaction in one stage axial compressor is numerically investigated for blade row ratio 1:1 and 2:3 at design point and for blade row ratio 2:3 at off-design point in two-dimensional view point. The numerical technique used is the upwind scheme of Van-Leer's Flux Vector Splitting(FVS) and Cubic spline interpolation is applied on zonal interface. In this study the flow unsteadiness due to potential interaction are found to be larger in blade row ratio 2:3 than in 1:1. The total pressure rise in blade row ratio 2:3 is closer to the real value in design point than that in 1:1. The change of unsteady pressure amplitude according to the variation of stator exit pressure is very small.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.2
• /
• pp.53-59
• /
• 2009

The analysis of injection molding process by CAE is widely used in development of plastic products. That comes from the fact that CAE analysis can reduce trial and error based on optimized design. On this study, by use of MOLDFLOW, the causes of product defects were found and solved by trade-off study. CAE analysis includes Flow-Cool-Warpage Analyses and finally a new mold-die design with better product quality was suggested. On injection molding of round-shaped plastic fan, new mold-die system with 4-tunnel gates located on the edge of a fan disc shows better quality rather than pin-point gate located on the center of a disc. That was effective in terms of flow mark removal and flatness improvement of the product.

• Journal of the Korean Institute of Gas
• /
• v.4 no.2 s.10
• /
• pp.7-14
• /
• 2000

LNG (Liquified Natural Gas) carried by LNG ship is unloaded into the LNG storage tanks at the very low temperature (a little lower than the boiling point of LNG). Because LNG is unloaded through the pipeline, two phase flow appears in the pipeline. In this study, we have studied the pressure-drop mechanisms of the two-phase flow in the pipeline, and the calculation method of BOG (Boil-off Gas) amount based on the heat transfer mechanism through the insulation and the surface of the pipeline. We have developed a computer program for thermal-hydraulic analysis on the LNG pipeline system. We have also developed the optimal design program to find the optimal thickness of insulation and the pipeline size. The program searches the optimal design with the minimum capital cost of pipelines and insulation on the operating conditions of maximum allowance pressure-drop and BOG amount, etc.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.7
• /
• pp.485-490
• /
• 2007

The LNG BOG re-liquefaction system for LNG carriers was designed based on the Claude refrigeration cycle and the thermodynamic analysis was carried out in order to find the design point of the three heat exchangers constituting the system. The thermodynamic analysis revealed that the system state could be defined by the three cold endpoint temperatures of the three-pass heat exchanger. Hence the iso-lines of the specific liquefaction work, taken as the performance indicator, were presented in terms of those three temperatures and discussed. The system was found most economical when those three temperatures approached a single temperature of $-140^{\circ}C$ and thus this system state could be taken as the design point for the heat exchangers.