• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.29 no.1
• /
• pp.57-68
• /
• 2019

Objective: The purpose of this study is to propose the benefits of reduction measures according to the occupational radon reference level in order to present basic data for radon management guidelines considering domestic circumstances. Methods: This study uses radon data measured in the subway stations from 2015 to 2016. Of the total of 4,643 cases, 4,231 cases were analyzed excluding the 412 cases where the values were below $300Bq/m^3$. Results: Cost-Benefit analysis was done on the results of the field survey on subway work sites. At the exposure level of $400Bq/m^3$, the ratio between the cost and the benefit was highest at 1 : 1.81(the cost was KRW 1,398,568,032, while the benefit KRW 2,5248,772,841). At the exposure level of $600Bq/m^3$, the ratio of cost and benefit was 1: 1.80, at $300Bq/m^3$ it was 1.72, at $800Bq/m^3$ it was 1.71, at $200Bq/m^3$ it was 1.54, and at $100Bq/m^3$ it was 1.40. Conclusions: Radon management in the workplace provides economic benefits and appropriate reduction strategies are needed. In addition, it is necessary to establish and distribute radon exposure assessment procedures and guidelines for the safety and health of employees when exceeding the exposure standard, and guidelines for radon management in the workplace should be established.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.9 no.1
• /
• pp.87-98
• /
• 1999

The objectives of this study were to evaluate exposures to airborne methylene chloride and postshift carboxyhemoglobin (COHb) in blood of workers engaged in processes using blowing or cleaning agents, and to investigate correlation between methylene chloride concentrations and the blood COHb levels of workers. The geometric mean (GM) of workers' exposures (8 hour-time weighted averages, TWA) to airborne methylene chloride during cleaning molds using rags wetted with the solvent in the manufacture of flexible polyurethane foam (GM = 61.4 ppm), during operating the dip tank for cleaning molds in the manufacture of lens (GM = 61.0 ppm), and during cleaning the blowing nozzles by spraying the solvent in the manufacture of shoes (GM = 117.2 ppm) were exceeded the American Conference of Governmental Industrial Hygienists (ACGIH) Threshold Limit Value ($TLV^{(R)}$)-Time Weighted Average (TWA) (50 ppm). The COHb levels were significantly different among groups (p<0.05). The average COHh levels in blood of non-smoking workers were 2.0% in. low-level (<50 ppm) exposure group, and 3.9 % in high-level (>50ppm) exposure group. The average COHb levels in smoking workers were 3.1% in low-level exposure group, and 4.8% in high-level exposure group. The blood COHb levels of no-exposed workers to methylene chloride were 1.8% in non-smoking group, and 2.8% in smoking group. It was found that the COHb level dependeds on the methylene chloride concentration and smoking habit, and was highly correlated with methylene chloride concentration in air. The correlation coefficient was 0.81 among non-smoking workers. The estimated COHb level (3.6%) and 95% upper confidence limit (4.0%) corresponding to TLV-TWA of methylene chloride exceeded the current ACGIH Biological Exposure Index (COHb 3.5%) for carbon monoxide. The estimated COHb level (5.4%) at 100 ppm exceeded the standard (5%) recommended by National Institute for Occupational Safety and Health (NIOSH) for preventing adverse cardiovascular effect. The estimated COHb value and 95% upper confidence limit at 25 ppm of the Occupational Safety and Health. Adminstration (OSHA) Permissible Exposure Limit-TWA (PEL-TWA) were 2.6% and 3.0%, respectively. It is suggested that COHb in blood be kept below 3.0% to comply with OSHA PEL-TWA.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.9
• /
• pp.831-840
• /
• 2013

The noise levels of workers in tunnel sites are likely to be high because tunneling work places are confined space. However, research on the noise exposure levels of tunneling workers have not been performed intensively due to restricted accessibility to tunnel construction sites. The aim of this study is to evaluate the noise exposure levels for workers engaged in tunneling work sites. Noise dosimeters were used for monitoring workers' noise exposure level in 5 tunneling work sites in accordance with the Notification of the Ministry of Labor. Among 5 tunneling work sites, 4 of them used NATM tunneling method and 1 work site used shield TBM tunneling method. The average noise exposure levels of NATM tunneling workers was 81.1 dB(A) and 15.4 % of the workers' noise level were exposed more than 90 dB(A) which is the exposure limit value. In Shield TBM tunneling method, 4.3 % of the workers were exposed more than 90 dB(A) of noise level, the average noise exposure levels of TBM tunneling workers was 84.1 dB(A).

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.22 no.2
• /
• pp.164-173
• /
• 2012

Objectives: Epichlorohydrin is a material that has been predicted to have high volatility and strong toxicity and is used normally in working area. Therefore, the hazardous and dangerous level and the foreign management system about epichlorohydrin should be invested at home and abroad and through hazard assessment for occupational environment measurement and exposure status of industrial workers in domestic working area. Methods: To assess risk and to suggest Development and Adoption to prevent health damage of workers owing to the epichlorohydrin exposure, the hazardousness and dangerousness of epichlorohydrin and its practical examples and regulation level for domestic and abroad health impairment are researched on the base of various references. Results: The epichlorohydrin caused skin and mucus membrane irritation, respiratory paralysis, kidney and live damage under the influence of acute toxicity and in animal study, it was confirmed as a doubtful carcinogenic substance to trigger reducement of sperm number and reproduction ability, abnormal spermatogenesis, mutagen, increase of forestomach epithelium and occurrence of papilloma and so on, as well as it induced stimulus asthma and allergic contact dermatitis for exposure workers. Conclusions: Epichlorohydrin was found to occur allergic contact dermatitis, carcinogenesis doubt and reproduction toxicity and was verified as a material which would be established reinforcement of management level to care health of handlers, such as denotement dangerousness of skin absorption.

• Safety and Health at Work
• /
• v.6 no.3
• /
• pp.174-183
• /
• 2015

The major purpose of this study is to construct a retrospective exposure assessment for benzene through a review of literature on Korea. Airborne benzene measurements reported in 34 articles were reviewed. A total of 15,729 individual measurements were compiled. Weighted arithmetic means [AM(w)] and their variance calculated across studies were summarized according to 5-year period intervals (prior to the 1970s through the 2010s) and industry type. Industries were classified according to Korea Standard Industrial Classification (KSIC) using information provided in the literature. We estimated quantitative retrospective exposure to benzene for each cell in the matrix through a combination of time and KSIC. Analysis of the AM(w) indicated reductions in exposure levels over time, regardless of industry, with mean levels prior to the 1980-1984 period of 50.4 ppm (n = 2,289), which dropped to 2.8 ppm (n = 305) in the 1990-1994 period, and to 0.1 ppm (n = 294) in the 1995-1999 period. There has been no improvement since the 2000s, when the AM(w) of 4.3 ppm (n = 6,211) for the 2005-2009 period and 4.5 ppm (n = 3,358) for the 2010-2013 period were estimated. A comparison by industry found no consistent patterns in the measurement results. Our estimated benzene measurements can be used to determine not only the possibility of retrospective exposure to benzene, but also to estimate the level of quantitative or semiquantitative retrospective exposure to benzene.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.10 no.1
• /
• pp.147-159
• /
• 2000

The NIOSH health hazard evaluation program (HHE program) was created in response to the mandate to determine the toxic effect and potential health hazard of workplace exposure, which is found in Occupational Safety and Health Act of 1970 and the Federal Mine Safety and Health Act of 1977, A primary benefit of HHE program is its ability to provide current health hazard data to employers and employees, which assists them in identifying solutions to occupational health and safety problems in their workplaces, The HHE program also stimulates research in the development and review of sampling methods and diagnostic tests and may prompt additional exposure assesment efforts and toxicological and epidemiological studies. HHE projects also provide human exposure-toxicity data that are used to asses the validity of existing occupational health standards and to support criteria for new standards of recommendation, The HHE request is classified into four categories: 1) category 1: As a administratively invalid, 2) category 2: These are valid requests for which a site visit is not essential to an appropriate response, 3) Category 3 : These are valid requests for which a site visit is necessary for an adequate evaluation, 4) These are valid request which present a complex problem or an opportunity for research, To carry out HHE program one or methods of investigation might be used: 1) direct observation and evaluation of production processes and employee work practices 2) employees exposure level and air contamination level 3) medical test or physical examinations of employees 4) private, confidential interviews with employees 5) review of employer's record of injuries and illness, employee exposure data, medical tests and job histories. After investigation and analysing the data, NIOSH issues a final report, giving finding and recommendation.

• Journal of Preventive Medicine and Public Health
• /
• v.33 no.3
• /
• pp.343-348
• /
• 2000

Objectives : This study was conducted to integrate the results of studies assessing the association between chronic noise exposure and blood pressure. Methods : Using a MEDLINE search with noise exposure, blood pressure and hypertension as key words, we retrieved articles from the literature that were published from 1980 to December 1999. The criteria for quality evaluation were as follows: 1) the study subjects must have been workers employed at a high noise level area 2) The paper should use average and cumulative noise exposure as method for exposure evaluation. 3) Blood pressure in each article should be reported in a continuous scale Among the 77 retrieved articles, six studies were selected for quantitative meta-analysis. Before the integration of the regression coefficients for the association between blood pressure and noise level, homogeneity tests were conducted. Results : All studies were a cross-sectional design and the study subjects were industrial workers. Five papers used a time-weighted average for noise exposure and only one paper calculated the cumulative noise exposure level. The measurement of blood pressure in the majority of studios were accomplished in a resting stale, and used an average of two or more readings. The homogeneity of studies was rejected in a fixed effect model, so we used the results in a random effect model. The results of the quantitative meta-analysis, the weighted regression coefficient of noise associated with systolic blood pressure and diastolic blood pressure were 0.05 (95% confidence interval [CI]: -0.03, 0.13) and 0.06 (95% CI: -0.01, 0.13), respectively. Conclusions : Our results suggested that chronic exposure to industrial noise does not cause elevated blood pressure.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.32 no.1
• /
• pp.10-20
• /
• 2022

Objectives: The aim of this study is to evaluate exposure levels of the extremely low frequency magnetic fields(ELF-MF) radiated from various electric facilities in Liquid Crystal Display(LCD) manufacturing processes. Methods: This study measured the exposure levels of personal and local ELF-MF for the electronic facilities installed in two LCD manufacturing companies. Samplers were installed around workers' waist during working hours to identify personal exposure levels, and direct reading equipment were located at 3 cm, 10 cm, and 30 cm away from the surface of the electronic facilities to measure local exposure levels. Average and maximum(ceiling) values were calculated for personal and local exposure levels. Results: Average and maximum of personal exposure levels for each worker were 0.56(mean) ± 0.02(SE) µT and 6.31 ± 0.75 µT, respectively. Statistical analyses of the study found that maximum of the personal exposure levels for engineers was significantly higher than that for operators since engineers spend more time near the electronic facilities for repairing. The range of maximum personal exposure levels was 0.50 ~ 43.50 µT and its highest level was equivalent to 4.35 % of ACGIH(American Conference of Governmental Industrial Hygienists) exposure limit value(1 mT). Maximum of local exposure levels was 8.18 ± 0.52 µT and the electronic facilities with higher exposure levels were roof rail and electric panel, which were not related to direct manufacturing. The range of maximum local exposure levels was 0.60 ~ 287.20 µT and its highest level was equivalent to 28.7 % of the ACGIH exposure limit value. Lastly, the local exposure levels significantly decreased as the measurement distance from the electronic facilities increased. Conclusions: Maximum of personal and local exposure levels did not exceed the exposure limit value of ACGIH. However, it is recommended to keep the workers as far as possible from the sources of ELF-MF.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.25 no.1
• /
• pp.95-103
• /
• 2015

Objectives: This study was conducted in order to better understand the conceptual model and Stoffenmanager nano module and apply it to the synthesis and packing processes of nanomaterials. Methods: Site visits were conducted to five nanomaterial production processes. Product and exposure variables were investigated in these workplaces. Hazard banding and exposure classification of the synthesis and packing processes of nanomaterials were conducted using documents and the website of Stoffenmanager Nano. Results: The five sites featured different products, packing tasks, ventilation and local exhaust, and others. The hazards for nano-nickel and copper were classified as E. The hazards for both fumed silica and indium tin oxide were classified as D. The hazard for spherical silica was classified as C. The exposure classes in the synthesis process of nanomaterials ranged from 2 through 4. The exposure classes in the packing process of nanomaterials ranged from 1 through 4. Conclusions: Application of Stoffenmanager nano to the synthesis and packing processes of nanomaterials helped to better understand the control level of the work environment and to suggest appropriate actions. The comparison of each process showed the effect of the production process and handling of solids and ventilation on exposure class.

• Journal of Environmental Health Sciences
• /
• v.48 no.2
• /
• pp.59-65
• /
• 2022

Background: Since people move through microenvironments rather than staying in one place, they may be exposed to both indoor and outdoor PM_2.5 concentrations. Objectives: The aim of this study was to assess the exposure level of each sub-population group and evaluate the contribution rate of the major microenvironments. Methods: Exposure scenarios for sub-population groups were constructed on the basis of a 2019 Time-Use survey and the previous literature. A total of five population groups were classified and researchers wearing MicroPEM simulated monitoring PM_2.5 exposure concentrations in real-time over three days. The exposure contribution for each microenvironment were evaluated by multiplying the inhalation rate and the PM_2.5 exposure concentration levels. Results: Mean PM_2.5 concentrations were 33.0 ㎍/m³ and 22.5 ㎍/m³ in Guro-gu and Wonju, respectively. When the exposure was calculated considering each inhalation rate and concentration, the home showed the highest exposure contribution rate for PM_2.5. As for preschool children, it was 90.8% in Guro-gu, 94.1% in Wonju. For students it was 65.3% and 67.3%. For housewives it was 98.2% and 95.8%, and 59.5% and 91.7% for office workers. Both regions had higher exposure to PM_2.5 among the elderly compared to other populations, and their PM_2.5 exposure contribution rates were 98.3% and 94.1% at home for Guro-gu and Wonju, respectively. Conclusions: The exposure contribution rate could be dependent on time spent in microenvironments. Notably, the contribution rate of exposure to PM_2.5 at home was the highest because most people spend the longest time at home. Therefore, microenvironments such as home with a higher contribution rate of exposure to PM_2.5 could be managed to upgrade public health.