• Nuclear Engineering and Technology
• /
• v.53 no.8
• /
• pp.2454-2463
• /
• 2021

The objective of this research is to the use of americium (AmO₂) as a burnable absorber effectively instead of conventional gadolinium (Gd₂O₃) for VVER-1200 reactor by analyzing its impacts on reactivity, power peaking factor (PPF), safety factor, and quality of the spent fuel. The assembly is burned to 60 GWd/t by using SRAC-2006 code and JENDL-4.0 data library for finding the optimum amount and effective way of using AmO₂ as a burnable absorber. From these studies, it is found that AmO₂ can decrease the excess reactivity like Gd₂O₃ without changing the criticality life span and enrichment of ²³⁵U. A homogeneous mixture of the 0.20% AmO₂+ 4.95% enriched UO₂ fuel rod (model MF-4) decreases the PPF than the reference assembly. The use of AmO₂+UO₂ in the integral burnable absorber (IBA) rod or the outer layer could also decrease the PPF up to 10 GWd/t but increases rapidly after 30 GWd/t, which could be a safety threat. The fuel temperature coefficient and void coefficient of the model MF-4 are the same as the reference assembly. In addition, 22% of initially loaded Am are burning effectively and contributing to the power production.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.10a
• /
• pp.281-284
• /
• 2008

This paper describes ASIC design of multimedia SoC Platform. The implemented Platform consists of 32-bit OpenRISC1200 Microprocessor, WISHBONE on-chip bus, VGA Controller, Debug Interface, SRAM Interface and UART. The 32-bit OpenRISC1200 processor has 5 stage pipeline and Harvard architecture with separated instruction/data bus. The VGA Controller can display RCB data on a CRT or LCD monitor. The Debug Interface supports a debugging function for the Platform. The SRAM Interface supports 18-bit address bus and 32-bit data bus. The UART provides RS232 protocol, which supports serial communication function. The Platform is design and verified on a Xilinx VERTEX-4 XC4VLX80 FPGA board. Test code is generated by a cross compiler' and JTAG utility software and gdb are used to download the test code to the FPGA board through parallel cable. Finally, the Platform is implemented into a single ASIC chip using Chatered 0.18um process and it can operate at 100MHz clock frequency.

• Journal of Oral Medicine and Pain
• /
• v.35 no.3
• /
• pp.165-175
• /
• 2010

Valproic acid (VPA) is a well-known anticonvulsive agent and has been used in the treatment of epilepsy for almost 30 years. VPA emerged in 1997 as an antineoplastic agent as well, when findings indicated the substance inhibited proliferation and induced differentiation of primitive neuroectocdermal tumor cells in vivo (Cinatl et al., 1997). Antitmor activity of VPA is associated with its targeting histone deacetylases. Bile acids and their synthetic derivatives induced apoptosis in various kinds of cancer cells and anticancer effects. It has been reported that the synthetic chenodeoxycholic acid (CDCA) derivatives showed apoptosis-inducing activity on various cancer cells in vitro. This study was undertaken to investigate the synergistic apoptotic effect of co-treatment with the histone deacetylases inhibitor, VPA and a CDCA derivative, HS-1200 on human osteosarcoma (HOS) cells. Cell viability was evaluated by trypan-blue exclusion. Induction and augmentation of apoptosis were confirmed by Hoechst staining, flow cytometry (DNA hypoploidy and MMP change), Westen blot analysis and immunofluorescent staining. In this study, HOS cells co-treated with VPA and HS-1200 showed several lines of apoptotic manifestation such as nuclear condensations, the reduction of MMP, the decrease of DNA content, the release of cytochrome c into cytosol, the translocation of AIF onto nuclei, and activation of caspase-7, caspase-3 and PARP whereas each single treated HOS cells did not. Although the single treatment of 1 mM VPA or $25\;{\mu}M$ HS-1200 for 48 h did not induce apoptosis, the co-treatment of them induced prominently apoptosis. Therefore our data provide the possibility that combination therapy of VPA and HS-1200 could be considered as a novel therapeutic strategy for human osteosarcoma.

• Journal of the Korea Society of Computer and Information
• /
• v.17 no.10
• /
• pp.11-23
• /
• 2012

To achieve efficient code size reduction, this paper proposes a new compressed instruction set architecture for the OpenRISC architecture. The new instructions and their corresponding formats are designed by the profiling information of the existing instruction usage. New 16-bit instructions and 32-bit instructions are proposed to compressed the existing 32-bit instructions and instruction sequences, respectively. The proposed instructions can be classified into three types. The first is the new 16-bit instructions for the frequent normal 32-bit instructions such as add, load, store, branch, and jump instructions. The second type is the new 32-bit instructions for the consecutive two load instructions, two store instructions, and 32-bit data mov instructions. Finally, two new 32-bit instructions are proposed to compress function prolog and epilog code, respectively. OpenRISC hardware decoder is extended to support the new instructions. Experiments show that the efficiency of code size reduction improves by an average of 30.4% when compared to the OR1200 instruction set architecture without loss of execution performance.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.12
• /
• pp.1200-1209
• /
• 2010

The main subject of this paper is to develop analytic method with which output power or sensitivity variations of a magnetostrictive ultrasonic transducer can be estimated with no aid of experiments. After the bias magnetic field deployed over the patch is calculated using finite element analysis for magnetostatics, the representative value is extracted by averaging these field values. The operating point on the characteristic curve for magnetostriction is identified by this value and then the output performance is calculated from it. It is verified that the results from this simple model match well with those of its experimental version and some limits of this modeling technique are also considered.

• Journal of Biosystems Engineering
• /
• v.9 no.2
• /
• pp.1-7
• /
• 1984

The engines mounted on power-tillers are used as power source in various kinds of works such as plowing, harrowing, transporting, spraying, water pumping and threshing, etc. But the engines have not been used effectively from a standpoint of fuel consumption because of lack of proper power transmission system and lack of understanding of fuel consumption characteristics of the engines. Therefore, this study was attempted to establish proper power transmission system between the power-tiller engines and various implements. In order to accomplish the above objective, firstly, power requirement and pulley sizes for various implements, which are driven by the power-tiller engines, were investigated to find out whether the power transmission system is proper. Secondly, partload variable engine-speed test was conducted for 3 different sizes of diesel engines to measure to specific fuel consumption. Thirdly, the present power transmission systems were analyzed in terms of specific fuel consumption, and proper power transmission systems were suggested for various implements. The results of this study are summarized as follows: 1. Power requirement for each fixed-type implement of power-tiller varied from 1.5 ps to 11 ps according to its type and operating conditions, but generally in the range of 2.5 ps to 7 ps. 2. Each power tiller and implement were equipped with only one size of pully with few exeptions. With the present power transmission systems, the engines can't be utilized effectively in terms of fuel economy. The pulley size of engine or implement should be diversified to provide the optimum engine speed for different implements. 3. For a diesel eninge with the rated power output of 6 ps, the optimum engine speed to minimize specific fuel consumption was 2200 rpm for the power reguirement in the range of 6 ps or more, 1700 rpm in the range of 4 to 6 ps, and 1200 rpm in the range of 4 ps or less. 4. For a diesel engine with the rated power output of 8 ps, the optimum engine speed was 2200 rpm for the power requirement in the range of 7 ps or more, 1700 rpm in the range of 4.8 to 7 ps, and 1200 rpm in the range of 4.8 ps or less. 5. For a diesel engine with the rated power output of 10 ps, the optimum engine speed was 2200 rpm for the power requirement in the range of 8.4 ps or more, 1700 rpm in the range of 5.4 ps to 8.4 ps, and 1200 rpm in thr range of 5.4 ps or less. 6. Provided the existing implements are dirven by 8 ps diesel engines, the optimum size of engine pulley should be larger than 120mm for the works of requiring less than 4 ps and 90-110mm for the works requiring 4.5-6.5 ps in order to minimize fuel consumption.

• Korean Journal of Materials Research
• /
• v.27 no.3
• /
• pp.155-160
• /
• 2017

Doped-$LaCrO_3$ perovskites, because of their good electrical conductivity and thermal stability in oxidizing and/or reducing environments, are used in high temperature solid oxide fuel cells as a gas-tight and electrically conductive interconnection layer. In this study, perovskite $(La_{0.8}Ca_{0.2})(Cr_{0.9}Co_{0.1})O_3$ (LCCC) coatings manufactured by atmospheric plasma spraying followed by heat treatment at $1200^{\circ}C$ have been investigated in terms of microstructural defects, gas tightness and electrical conductivity. The plasma-sprayed LCCC coating formed an inhomogeneous layered structure after the successive deposition of fully-melted liquid droplets and/or partially-melted droplets. Micro-sized defects including unfilled pores, intersplat pores and micro-cracks in the plasma-sprayed LCCC coating were connected together and allowed substantial amounts gas to pass through the coating. Subsequent heat treatment at $1200^{\circ}C$ formed a homogeneous granule microstructure with a small number of isolated pores, providing a substantial improvement in the gas-tightness of the LCCC coating. The electrical conductivity of the LCCC coating was consequently enhanced due to the complete elimination of inter-splat pores and micro-cracks, and reached 53 S/cm at $900^{\circ}C$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.325-325
• /
• 2011

Very initial stage of oxidation process of Si (001) surface at room temperature (300 K) and high temperature (1200 K) was investigated using large scale molecular dynamics simulation. Reactive force field potential [1] was used for the simulation owing to its ability to handle charge variation as well as breaking and forming of bonds associated with the oxidation reaction. The results show that oxygen molecules adsorb dissociatively or otherwise leave the silicon surface. Initial position and orientation of oxygen molecule above the surface play important role in determining final state and time needed to dissociate. At 300 K, continuous transformation of ion $Si^+$ (or suboxide Si2O) to $Si2^+$ (SiO), $Si3^+$ (Si2O3) and finally to $Si4^+$ (SiO2) clearly observed. High temperature silicon surface provide heat energy that enable oxygen atom to penetrate into deeper silicon surface. The heat energy also retards adsorption process. As a result, transformation of ion $Si^+$ is impeded at 1200 K.

• Korean Journal of Clinical Laboratory Science
• /
• v.36 no.2
• /
• pp.199-204
• /
• 2004

Height has become one of the most important factors to determine the pulmonary function test index, and there is a high correlation between them, so that they have been utilized for evaluating pulmonary function test predictive value or nomogram. Therefore, we have tried to find out that difference and if there is any correlation and linear relationship between height and forced expiratory flow curve. There were a total of 163 subjects, male 93 and female 70. This study was done at the Department of Pulmonary Function Test of Jeon-Ju Presbyterian Hospital and we measured the index at the forced expiratory flow curve of FVC, $FEV_{1.0}$, $FEV_{1.0}$/FVC, $FEF_{25-75%}$, and $FEF_{200-1200m{\ell}}$. When we subjected the group of height more than 160cm, there were gradual increments at FVC(p<0.001), $FEV_{1.0}$(p<0.001), $FEF_{25-75%}$(p<0.05) and $FEF_{200-1200m{\ell}}$(p<0.001), but no changes at $FEV_{1.0}$/FVC in terms of forced expiratory flow curve index. We have analyzed the relationship between height and forced expiratory flow curve, there was a close relationship at FVC(r=0.670, p<0.01), $FEV_{1.0}$(r=0.491, p<0.01), $FEF_{25-75%}$ (r=0.175, p<0.05) and $FEF_{200-1200m{\ell}}$(r=0.370, p<0.01) but there was reciprocal relationship at $FEV_{1.0}$/FVC(r=-0.215, p<0.01). We have tried simple regression analysis to see if height affects forced expiratory flow curve index as a sector, and the result was $FVC(\ell)=0.0642{\times}height(cm)-7.2978$(p<0.01, $R^2=0.449$), $FEV_{1.0}(\ell)=0.0407{\times}height(cm)-4.2774$ (p<0.01, $R^2=0.2411$), $FEV_{1.0}/FVC(%)=-0.2892{\times}height(cm)+121.44$(p<0.01, $R^2=0.0464$), $FEF_{25-75%}(\ell/sec)=0.0176{\times}height(cm)-0.7876$(p<0.05, $R^2=0.0237$), $FEF_{200-1200m{\ell}}(\ell/sec)=0.0967{\times}height(cm)-11.037$(p<0.01, $R^2=0.1214$) this was approved statistically. According to this study, if height is taller than average, forced expiratory flow curve index were increased, there was a close relationship between height and forced expiratory flow curve, and there was a linear relationship as sector between height and forced expiratory flow curve index. Therefore, researches that study other factors such as sex, age, weight, body surface area, and obesity indexes other than height should be done to see if there are any further relationships.

• Journal of Chest Surgery
• /
• v.24 no.12
• /
• pp.1197-1200
• /
• 1991

Polypoid lesions of the esophagus occur infrequently and may be benign or malignant. Pseudosarcoma, a malignant polypoid tumor of the esophagus is rare and appears to be a distinct pathological entity; the polypoid portion is composed of sarcomatous spindle cells and the base of the polyp shows in situ or invasive squamous cell carcinoma. We experienced a case of pseudosarcoma of the esophagus and report the case with the review of literature.