• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.427-428
• /
• 2008

New high efficiency green light emitting phosphorescent devices with emission layers of [TCTA/TCTA:TAZ/TAZ]:Ir$(ppy)_3$ have been fabricated and evaluated in this paper. Among the devices having different thicknesses of TCTA:TAZ mixed layer in the total 300$\AA$-thick host of TCTA(80$\AA$)/TCTA:TAZ (50~100$\AA$)/TAZ, the device with host of TCTA(80$\AA$)/TCTA:TAZ(90$\AA$)/TAZ(130$\AA$) showed the best electroluminescent characteristics with the current density of 95 mA/$cm^2$ and luminance of 25,000 cd/$m^2$ at an applied voltage of 10V. The maximum current efficiency was 52 cd/A under the luminance of 400 cd/$m^2$.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.595-596
• /
• 2006

The flexible organic thin film transistor (OTFT) array to use as a switching device for an organic light emitting diode (OLED) was designed and fabricated in the microcontact printing and low-temperature processes. The gate, source, and drain electrode patterns of OTFT were fabricated by microcontact printing which is high-resolution lithography technology using polydimethylsiloxane(PDMS) stamp. The OTFT array with dielectric layer and organic active semiconductor layers formed at room temperature or at a temperature tower than $40^{\circ}C$. The microcontact printing process using SAM(self-assembled monolayer) and PDMS stamp made it possible to fabricate OTFT arrays with channel lengths down to even nano size, and reduced the procedure by 10 steps compared with photolithography. Since the process was done in low temperature, there was no pattern transformation and bending problem appeared. It was possible to increase close packing of molecules by SAM, to improve electric field mobility, to decrease contact resistance, and to reduce threshold voltage by using a big dielecric.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.224-224
• /
• 2016

Many researchers have been tried to improve the performance of the phosphorescent organic light-emitting diode(PHOLED) by controlling of the dopant profile in the emission layer. In this work, as shown in Fig. 1 insert, a typical red PHOLED device which has the structure of ITO/NPB(50nm)/CBP(30nm)/TPBi(10nm)/Alq3(20nm)/LiF(0.8nm)/Al(100nm) is fabricated with a 5nm thick doping section in the emission layer. The doping section is formed by co-deposition of CBP and Ir(btp)2acac with a doping concentration of 8%, and it's location(x) is changed from HTL/EML interface to EML/HBL in 5nm steps. The current efficiency versus current density of the devices are shown in Fig. 1. By changing the location of doping section, as shown in Fig. 1 and 2, at x=5nm, the efficiency shows the maximum of 3.1 cd/A at 0.5 mA/cm2 and it is slightly decreased when the section is closed to HTL and slightly increased when the section is closed to HBL. If the doping section is closed to HTL(NPB) the excitons can be quenched easily to NPB's triplet state energy level(2.5eV) which is relatively lower than that of CBP(2.6eV). Because there is a hole accumulation at EML/HBL interface the efficiency can be increased slightly when the section is closed to HBL. Even the thickness of the doping section is only 5nm,. the maximum efficiency of 3.1 cd/A with x=5 is closed to that of the homogeneously doped device, 3.3 cd/A, because the diffusion length of the excitons is relatively long. As a result, we confirm that the current efficiency of the PHOLED can be improved by the doping profile optimization such as partially, not homogeneously, doped EML structure.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 C
• /
• pp.1890-1892
• /
• 2005

Recently, high luminance and high efficiency were realized in OLEDs with multilayer structure including emitting materials such as metal-chelate complexes. New luminescent materials, [2- (2-hydroxyphenyl)-quinoline] (Zn(HPB)q), [(1,10-phenanthroline)- (8-hydroxyquinoline)] Zn(Phen)q was synthesized. Zn-Complexes have low molecular compound and thermal stability. The ionization potential(IP) and electron affinity(EA) of Zn-complexes were measured by cyclic-voltammetry(CV). The fundamental structure of the OLEDs was $ITO/{\alpha}$-NPD/Zn-Complex/Al and then we made device structure rightly in energy band gap. We using Zn(Phen)q as emitting layer and Zn(HPB)q as electron transport layer. We measured current density-voltage, luminance-voltage characteristics.

• 대한전자공학회논문지SD
• /
• 제45권5호
• /
• pp.12-18
• /
• 2008

본 연구는 PC(polycarbonate) 기판 위에 소스(source)/드레인(drain) 전극으로 Ag 페이스트를 스크린 인쇄하여 OTFT(organic thin film transistor)를 제작하였다. 또한 이렇게 제작된 OTFT를 적용하여 OTFT-OLED(organic light emitting diode) 어레이를 제작하였으며 OTFT의 소스 및 드레인 전극과 더불어 데이터 배선전극을 Ag 페이스트를 이용하여 형성하였다. Ag 페이스트는 스크린 마스크의 mesh에 따라 325 mesh용과 500 mesh용을 사용하였으며, 325 mesh용 페이스트는 선폭 60 ${\mu}m$, 500 mesh용 페이스트는 선폭 40 ${\mu}m$까지 인쇄가 가능하였다. 그리고 면저항은 각각 $60m{\Omega}/\square,\;133.1m{\Omega}/\square$이었다. 제작된 OTFT의 성능은 이동도가 자각 0.35 $cm^2/V{\cdot}sec$와 0.12 $cm^2/V{\cdot}sec$, 문턱전압 -4.7 V와 0.9 V이었으며, 전류 점멸비는 ${\sim}10^5$이었다. OTFT-OLED 어레이는 인쇄성이 우수한 500 mesh용 Ag 페이스트를 사용하였으며 OTFT의 채널길이를 50 ${\mu}m$로 설계하여 제작하였다. OTFT-OLED 어레이의 화소는 2개의 OTFT, 1개의 캐패시터 그리고 1개의 OLED로 구성하였고, 크기는 $2mm{\times}2mm$이며, 해상도는 $16{\times}16$ 이다. 제작된 어레이는 일부 불량 화소를 포함하고 있지만 능동형 모드로 동작함을 확인할 수 있었다.

• Journal of Information Display
• /
• 제5권1호
• /
• pp.28-33
• /
• 2004

A high voltage NMOSFET is proposed to drive top emission organic light emitting device (OLED) used in the organic electroluminescent (EL) display on the single crystal silicon substrate. The high voltage NMOSFET can be fabricated by utilizing a simple layout technique with a standard CMOS logic process. It is clearly shown that the maximum supply voltage ($V_{DD}$) required for the pixel-driving transistor could reach 45 V through analytic and experimental methods. The high voltage NMOSFET was fabricated by using a standard 1.5 ${\mu}m$, 5 V CMOS logic process. From the measurements, we confirmed that the high voltage NMOSFET could sustain the excellent saturation characteristic up to 50 V without breakdown phenomena.

• Transactions on Electrical and Electronic Materials
• /
• 제10권6호
• /
• pp.203-207
• /
• 2009

We have investigated the effect of ambient gases on the structural, electrical, and optical characteristics of ITO thin films intended for use as anode contacts in OLED (organic light emitting diodes) devices. These ITO thin films are deposited by radio frequency (RF) magnetron sputtering under different ambient gases (Ar, Ar+$O_2$, and Ar+$H_2$) at $300{^{\circ}C}$. In order to investigate the influences of the oxygen and hydrogen, the flow rate of oxygen and hydrogen in argon mixing gas has been changed from 0.5 sccm to 5 sccm and from 0.01 sccm to 0.25 sccm, respectively. The intensity of the (400) peak in the ITO thin films increased with increasing $O_2$, flow rate whilst the (400) peak was nearly invisible in an atmosphere of Ar+$H_2$. The electrical resistivity of the ITO thin films increased with increasing $O_2$ flow rate, whereas the electrical resistivity decreased sharply under an Ar+$H_2$ atmosphere and was nearly similar regardless of the $H_2$ flow rate. The change of electrical resistivity with changes in the ambient gas composition was mainly interpreted in terms of the charge carrier mobility rather than the charge carrier concentration. All the films showed an average transmittance of over 80% in the visible range. The OLED device was fabricated with different ITO substrates made with the configuration of ITO/$\alpha$-NPD/DPVB/$Alq_3$/LiF/Al in order to elucidate the performance of the ITO substrate. Current density and luminance of OLED devices with ITO thin films deposited in Ar+$H_2$ ambient gas is the highest among all the ITO thin films.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.155-158
• /
• 2007

Printed organic thin-film transistor(OTFT) to use as a switching device for an organic light emitting diode(OLED) were fabricated in the microcontact printing and direct printing processes at room temperature. The gate electrodes($5{\mu}m$, $10{\mu}m$, and $20{\mu}m$) of OTFT was fabricated using microcontact printing process, and source/drain electrodes ($W/L=500{\mu}m/5{\mu}m$, $500{\mu}m/10{\mu}m$, and $500{\mu}m/20{\mu}m$) was fabricated using direct printing process with hard poly(dimethylsiloxane)(h-PDMS) stamp. Printed OTFT with dielectric layer was formed using special coating system and organic semiconductor layer was ink-jet printing process. Microcontact printing and direct printing processes using h-PDMS stamp made it possible to fabricate printed OTFT with channel lengths down to $5{\mu}m$, and reduced the process by 20 steps compared with photolithography. As results of measuring he transfer characteristics and output characteristics of OTFT fabricated with the printing process, the field effect characteristic was verified.

• 한국전기전자재료학회논문지
• /
• 제26권12호
• /
• pp.899-903
• /
• 2013

We investigated the luminescence properties of $Alq_3$ in the device structure of ITO/CuPc/TPD/$Alq_3$/Al. The CuPc as a hole-injection material and TPD as hole-transport material. Emission properties were measured by varying a layer thickness of CuPc (0 nm to 50 nm), which is the hole-injection layer. As a result, it was found that the hole injection occurs smoothly when the layer thickness was 20 nm among the thicknesses from 0 nm to 50 nm.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.588-591
• /
• 2004

Polyazomethine type conjugated copolymers containing phenanthridine units, poly(PZ-PTI), were synthesized by Schiff-base reaction. This new conjugated copolymer exhibited improved solubility in common organic solvents due to the presence of alkyl side chains as well as phenanthridine groups. Double layer (ITO/poly(PZ-PTI)/$Alq_3$/Mg) light emitting diode (LED) exhibited enhanced EL emission and efficiency compared to that of single layer (ITO/poly(PZ-PTI)/Mg) LED. With increasing the thickness of $Alq_3$ layer in double layer (ITO/poly(PZ-PTI)/$Alq_3$/Mg) LED the emission peak gradually shifted to the single layer (ITO/$Alq_3$/Mg) LED, confirming good hole transporting behaviour of the synthesized conjugated copolymer.