• Nuclear Engineering and Technology
• /
• 제40권2호
• /
• pp.99-106
• /
• 2008

Through mechanical alloying, hot isostatic pressing and hot rolling, a 9%Cr Fe-based oxide dispersion-strengthened alloy sample was fabricated. The tensile strength of the alloy is significantly improved when the microstructure is modified during the post-consolidation process. The alloy samples were strengthened as the cooling rates increased, though the elongation was somewhat reduced. With a cooling rate of $800^{\circ}C/s$ after normalization at $1150^{\circ}C$, the alloy sample showed a tensile strength of 1450 MPa, which is about twice that of the hot rolled sample; however, at $600^{\circ}C$ the tensile strength dramatically decreased to 620 MPa. Optical microscope and transmission electron microscope were used to investigate the microstructural changes of the specimens. The resultant strengthening of the alloy sample could be mainly attributed to the interstitially dissolved nitrogen, the fraction of the tempered martensite, the fine grain and the presence of a smaller precipitate. The decrease in the tensile strength was mainly caused by the precipitation of vanadium-rich nitride.

• Nuclear Engineering and Technology
• /
• 제52권2호
• /
• pp.337-343
• /
• 2020

Oxide dispersed strengthened (ODS) steel is an important candidate for Gen-IV reactors. Oxide embedded in Fe can help to trap irradiation defects and enhances the strength of steel. It was observed in this study that the size of oxide has a profound impact on the depinning mechanism. For smaller sizes, the oxide acts as a void; thus, letting the dislocation bypass without any shear. On the other hand, oxides larger than 2 nm generate new dislocation segments around themselves. The depinning is similar to that of Orowan mechanism and the strengthening effect is likely to be greater for larger oxides. It was found that higher shear deformation rates produce more fine-tuned stress-strain curve. Both molecular dynamics (MD) simulations and BKS (Bacon-Knocks-Scattergood) model display similar characteristics whereby establishing an inverse relation between the depinning stress and the obstacle distance. It was found that (110)_oxide || (111)_Fe (oriented oxide) also had similar characteristics as that of (100)_oxide || (111)_Fe but resulted in an increased depinning stress thereby providing greater resistance to dislocation bypass. Our simulation results concluded that critical depinning stress depends significantly on the size and orientation of the oxide.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2013년도 춘계학술대회 논문집
• /
• pp.816-821
• /
• 2013

This case study presents a practical method to reduce resonant vibration of generator-motor set. The generator is driven at 1800rpm by induction integral motor. The vibration is below alarm limits, but the dominant frequency of vibration is sub-synchronous and close to that of bearing fault signal in spite of new bearings. To find an mechanism of abnormal vibration, ODS and Modal analysis is carried out. The measured modal characteristics were compared with those of FE Analysis. The ODS mode at rated speed is consistent with system natural frequency mode that is excited by bearings. To reduce vibration level, the isolation mount at system base is changed with new rubber mount for lower natural frequency.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2003년도 international symposium on advanced powder metallurgy
• /
• pp.65-66
• /
• 2003

1. The oxidation resistance of $Y_{2}O_{3}$ containing Ni-base alloy is superior to that of the alloy without $Y_{2}O_{3}$. 2. The appearance of oxides of Ni-20Cr-20Fe-5Nb-$1Y_{2}O_{3}$ alloy is similar to that of oxides in commercial PM1000 and MA754 alloy. 3. The oxides in ODS alloy are grown mainly at particle boundaries.

• Nuclear Engineering and Technology
• /
• 제53권8호
• /
• pp.2582-2590
• /
• 2021

The high-energy milling is one of the most extended techniques to produce Oxide dispersion strengthened (ODS) powder steels for nuclear applications. The consequences of the high energy mill process on the final powders can be measured by means of deformation level, size, morphology and alloying degree. In this work, an ODS ferritic steel, Fe-14Cr-5Al-3W-0.4Ti-0.25Y₂O₃-0.6Zr, was fabricated using two different mechanical alloying (MA) conditions (M_std and M_act) and subsequently consolidated by Spark Plasma Sintering (SPS). Milling conditions were set to evidence the effectivity of milling by changing the revolutions per minute (rpm) and dwell milling time. Differences on the particle size distribution as well as on the stored plastic deformation were observed, determining the consolidation ability of the material and the achieved microstructure. Since recrystallization depends on the plastic deformation degree, the composition of each particle and the promoted oxide dispersion, a dual grain size distribution was attained after SPS consolidation. M_act showed the highest areas of ultrafine regions when the material is consolidated at 1100 ℃. Microhardness and small punch tests were used to evaluate the material under room temperature and up to 500 ℃. The produced materials have attained remarkable mechanical properties under high temperature conditions.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.1039-1042
• /
• 2002

SMD(Surface Mounting Device) which mounts electronic components as IC-Chips on PCB automatically, produces a large dynamic force and vibration. The unwanted vibrations in SMD degrade the performance of the precision device and it is the major obstacle to limit its speed for mounting. This study investigated the vibration analysis of a typical SMD to predict the natural frequencies and mode shapes. To validate the finite element analysis of SMD, the FE result was compared with that of ODS measurements. It was shown that the predicted results were well correlated with the experimental modal parameters.

• 한국분말재료학회지
• /
• 제28권5호
• /
• pp.375-380
• /
• 2021

In this study, we investigate the effect of the duration of mechanical alloying on the microstructures and mechanical properties of ODS ferritic/martensitic steel. The Fe(bal.)-10Cr-1Mo pre-alloyed powder and Y₂O₃ powder are mechanically alloyed for the different mechanical alloying duration (0 to 40 h) and then constantly fabricated using a uniaxial hot pressing process. Upon increasing the mechanical alloying time, the average powder diameter and crystallite size increased dramatically. In the initial stages within 5 h of mechanical alloying, inhomogeneous grain morphology is observed along with coarsened carbide and oxide distributions; thus, precipitate phases are temporarily observed between the two powders because of insufficient collision energy to get fragmented. After 40 h of the MA process, however, fine martensitic grains and uniformly distributed oxide particles are observed. This led to a favorable tensile strength and elongation at room temperature and 650℃.

• 한국분말재료학회지
• /
• 제15권1호
• /
• pp.23-30
• /
• 2008

Ni-20Cr-20Fe-5Nb alloy with or without $Y_2O_3$ was manufactured by mechanical alloying process and consolidated by spark plasma sintering (SPS). The grain size of the alloy with $Y_2O_3$ was smaller than that of alloy without $Y_2O_3$ which results from the effect of $Y_2O_3$ suppressing grain growth. The tensile strength at room temperature was increased by the addition of $Y_2O_3$ but decreased abruptly at temperature above $600^{\circ}C$. It seems to result from the change of deformation mechanism due to fine grain size, that is, grain boundary sliding is predominant at above $600^{\circ}C$ while internal dislocation movement is predominant at below $600^{\circ}C$. After conventional heat treatment process of solution treatment and aging, a small amount of ${\delta}(Ni_3Nb)$ phase was formed in Ni-20Cr-20Fe-5Nb alloy while a large amount of ${\gamma}"(Ni_3Nb)$ was formed in Inconel 718 in the previous report. This is due to exhaustion of Nb content by the formation of NbC during consolidation.

• Preventive Nutrition and Food Science
• /
• 제2권3호
• /
• pp.191-196
• /
• 1997

The antioxidative activity of seven different acylated anthocyanin pigments isolated from grape, sweet potato, eggplant and red cabbage was evaluated bvy using linoleic acid autoxidation and rat liver microsomal systems. The acylated anthocyanins were isolated and purified by Amberlite SAD-7, ODS and Sephadex LH-20 column omatography, and preparative HPLC. Most of acylated anthocyanisns exhibited antioxidative activity as strong as $\alpha$-tocoperol, and especially peonidin3-O--(6-O-trans-caffeyl)-2-O-(6-O-trans-feuloylglucopyranosyl)-$\beta$-D-glucopyranosyl-5-O-$\beta$-D-glucopyranoside from purple sweet potato showed the strongest activity, comparable to BHA (not significant, p<0.05) in the linoleic acid system. Meanwhile, two acylated anthocyanins from the pericarps of grape and eggplant inhibited considerably the MDA formation from rat liver microsomal lipid peroxidation induced by FeSO$_4$/$H_2O$$_2$. In particular, malvidin 3-O-(6-O-p-coumaroyl)-$\beta$-D-glucopyranosde from grape pericarps showed the strongest antioxidant activity, comparable to $\alpha$-tocopherol (not significant, p<0.05). These results suggest that the acylated anthocyanins from fruits and vegetables can be used as potential dietary ntioxidants and natural colorants.

• 한국식품위생안전성학회지
• /
• 제34권2호
• /
• pp.148-157
• /
• 2019

본 연구는 현재 우리나라에서 착색료로 사용허가 되어 있지만 아직 분석법이 개발되지 않은 철클로로필린나트륨의 최적 분석법을 개발하기 위하여 진행되었다. 철클로로필린나트륨은 HPLC-PDA (390 nm), Inertsil ODS-2 column, 1% 초산을 함유한 메탄올-물(80:20, v/v)을 이동상으로 분석할 때 가장 우수한 분리능과 재현성을 나타내었다. UPLC/MS를 통하여 철클로로필린나트륨의 주유도체를 확인한 결과 철 클로린 e4(Fe-chlorin e4)와 철 이소클로린 e4(Fe-isochlorin e4)가 피크의 주요 구성성분임을 확인하였다. 최적 분석법의 타당성을 확보하기 위해 직선성, 검출한계, 정량한계, 정확도, 정밀도, 회수율 분석을 실시하였다. 검량선의 $R^2$은 0.9999, 검출한계는 0.1 mg/kg, 정량한계는 0.3 mg/kg로 나타나 직선성, 검출 한계, 정량한계가 모두 우수하였다. 정확도는 일내분석 93.9~100.8%, 일간분석 99.3~104.95%로 나타났고, 정밀도는 일내분석 2.0~5.4%, 일간분석 4.6~7.7%로 나타났다. 회수율은 수용성 식품(캔디)과 지용성 식품(샐러드드레싱)에서 각각 93.3~104.4%(RSD 0.3~4.3%)과 82.6~114.9%(RSD 1.2~2.0%)로 나타나 국제표준화 기구(ISO)의 기준에 적합하였다. 본 연구는 식품 중 함유된 철클로로필린나트륨을 분석하고 그 유도체를 확인한 결과로 향후 공인분석 방법으로 활용 가치가 클 것으로 기대된다.