• Progress in Superconductivity and Cryogenics
• /
• v.10 no.1
• /
• pp.10-14
• /
• 2008

Differently from BSCCO tapes which are fabricated by powder-in-tube method, the coated conductors are made by the evaporation of YBCO on metal substrate. Due to this structural merit, although the coated conductors are generally used for large current transportation, they are expected to be favorable to the purpose of the fault current limitation as well. In this study, using YBCO coated conductor having copper stabilizer formed by plating technique(produced by Superpower Co.), we investigated the over-current characteristics of the coated conductor. The coated conductors had 85 A $I_c$ and 90 K $T_c$. The resistance of the conductor was 0.93 $m{\Omega}/cm$ at 300 K and 0.17 $m{\Omega}/cm$ at the temperature right above $T_c$. To the coated conductors, we applied the voltages of the range from 150 $V_{rms}$ to 230 $V_{rms}$ and measured the V-I curves using four probe method. From the results, we could analyze the electric behavior of the coated conductor in flux flow state. As the current exceed $I_c$, the currents were distributed into the superconductor and metal stabilizer. The amounts of the currents shared through both current paths were calculated under the assumption that the ,Joule heating was perfectly eliminated by $LN_2$ surrounding the conductor. Finally, the condition for the stable current flowing state which does not affect the conductor was established from the analysis on the over-current characteristics.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.39 no.4
• /
• pp.271-279
• /
• 2013

Water-soluble collagen (30 wt%) was entrapped within oil phase of lipstick using reversed micelle method to improve the moisture capacity of the lipstick. Reversed micelles containing collagen were prepared using caprylic/capric triglyceride as external phase and polyoxyethylene (10) octylphenyl ether (Triton X-100) and 1-dodecanol as surfactant and co-surfactant, respectively. The formation of reversed micelle encapsulating collagen was confirmed by measuring electric conductivity and UV-vis spectrum using methylene blue (MB). The stability and moisture capacity of the lipstick containing 20 wt% collagen encapsulated reversed micelles were observed by measuring rheology property, moisture content and amino acid content. The molecular ratio (W, water-pool) of water to surfactant (Triton X-100) in the most stable reversed micelle was ${\leq}$ 10. The hardness of the lipstick had no difference with that of the lipstick without reversed micelle, and the moisture content was increased to 59% and the amino acid content was 92.7%.

• (The)Study of the Eastern Classic
• /
• no.67
• /
• pp.345-378
• /
• 2017

In the scriptures of "$Ch{\bar{u}}n-qi{\bar{u}}$(春秋)", the expression method of '$Ch{\bar{u}}n-w{\acute{a}}ng-zh{\bar{e}}ng-yu{\grave{e}}$(春王正月 : It's spring. It's the first month regulated by the king.)' was used as Jì-yuè-fǎ(紀月法 : the rules to determine the first month(正月)), the month of winter solstice was regarded as the first month of a year, and three years since then were named as $Ch{\bar{u}}n$(春 : spring). With regard to this "$Ch{\bar{u}}n-qi{\bar{u}}$"Wáng-lì("春秋"王曆 : the calendar regulated by the king of $Zh{\bar{o}}u$(周) dynasty in "$Ch{\bar{u}}n-qi{\bar{u}}$"), depending on whether Confucius(孔子) changed and recorded the names of the months and the season or not, there were three different arguments; the theory that 'Confucius changed the names of both the months and the season'(孔子改月 改時說), the view that 'Confucius changed the name of the season, not the names of the months'(孔子不改月 改時說), and then the theory that 'Confucius changed neither the names of the months nor the name of the season'(孔子不改月 不改時) since Song(宋) dynasty. The first view was taken by $Hh{\acute{u}}-{\bar{a}}n-gu{\acute{o}}$(胡安國) and $C{\grave{a}}i-ch{\acute{e}}n$(蔡沈), and the second theory was mentioned by Chéng-yí(程?) and Zhū-zǐ(朱子). The advocates of the third view had become remarkable since Ming(明) dynasty, and one of representatives was Wàng-yáng-míng(王陽明). All of them based their arguments on ancient scriptures and Confucian legal books, and there were cases of taking the same records as the support for different opinions. Confucius' so-called 'Chūn-qiū-bǐ-fǎ(春秋筆法 : the method to describe historical facts by making clear discrimination between right and wrong)' and '$Sh{\grave{u}}-{\acute{e}}r-b{\grave{u}}-zu{\grave{o}}$(述而不作 : the attitude to succeed virtuous men's achievements and only explain and describe them not creating and adding new contents)' could come from thoughts of $Z{\bar{u}}n-w{\acute{a}}ng$(尊王 : to respect the king with the virtues of benevolence, righteousness, propriety, wisdom and sincerity). Therefore, even though Confucius is assumed to have been the writer of "$Ch{\bar{u}}n-qi{\bar{u}}$(春秋)", whether he actually changed and recorded the names of the months and the season in the calendar used in "$Ch{\bar{u}}n-qi{\bar{u}}$" is doubtful. These theories on Confucius's intervention in the calendar of "$Ch{\bar{u}}n-qi{\bar{u}}$" hadn't been discussed as conflicting in reality until Tang(唐) dynasty.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.19 no.3
• /
• pp.153-163
• /
• 2017

The objective of this study is to enhance the model's speed of estimating weather variables (e.g., minimum/maximum temperature, sunshine hour, PRISM (Parameter-elevation Regression on Independent Slopes Model) based precipitation), which are applied to the Agrometeorological Early Warning System (http://www.agmet.kr). The current process of weather estimation is operated on high-performance multi-core CPUs that have 8 physical cores and 16 logical threads. Nonetheless, the server is not even dedicated to the handling of a single county, indicating that very high overhead is involved in calculating the 10 counties of the Seomjin River Basin. In order to reduce such overhead, several cache and parallelization techniques were used to measure the performance and to check the applicability. Results are as follows: (1) for simple calculations such as Growing Degree Days accumulation, the time required for Input and Output (I/O) is significantly greater than that for calculation, suggesting the need of a technique which reduces disk I/O bottlenecks; (2) when there are many I/O, it is advantageous to distribute them on several servers. However, each server must have a cache for input data so that it does not compete for the same resource; and (3) GPU-based parallel processing method is most suitable for models such as PRISM with large computation loads.

• Journal of Food Hygiene and Safety
• /
• v.14 no.4
• /
• pp.339-345
• /
• 1999

The present study was performed to investigate photodegradation rate constants and degradation products of dichlorvos and methidathion by the USEPA method. The two pesticides were very stable in sunlight for 16 days from September 2 to 18, 1998 and humic acid had no sensitizing effect on the photolysis of each pesticide in sunlight. The photolysis rate was fast-est for methidathion, followed by dichlorvos in the presence of UV irradiation. Photodegradation rate constant and half-life of dichlorvos were 0.0208 and 33.3 min, respectively. Photodegradation rate constant and half-life of methidathion were 0.6789 and 1.0min, respectively. The two pesticides were degraded completely in the presence of UV irradiation and UV irradiation with TiO$_2$in about 3 hours. Therefore, it is suggested that UV treatment will be effective for the degradation of pesticides in the process of drinking water purification. In case of dichlorvos and methidathion, UV irradiation with TiO$_2$was more effective for degradation than W irradiation. In order to identify photolysis products, the extracts of degradation products were analyzed by GC/ MS. The mass spectrum of photolysis products of dichlorvos was at m/z 153, those of the photolysis of methidathion were at m/z 198 and 214, respectively. Photolysis products of dichlorvos was Ο, Ο-dimethyl phosphate(DMP), those of methidathion were Ο, Ο-dimethyl phosphorothioate(DMTP) and Ο, Ο-dimethyl phosphorodithioate (DMDTP).

• Journal of the Korean Applied Science and Technology
• /
• v.32 no.4
• /
• pp.758-766
• /
• 2015

Dextran is a generic term for a bacterial exopolysaccharide synthesized from sucrose and composed of chains of D-glucose units connected by ${\alpha}$-1,6-linkages by using dextransucrases. Dextran could be used as vicosifying, stabilizing, emulsifying, gelling, bulking, dietary fiber, prebiotics, and water holding agents. We isolated new strain capable of producing dextran from Korean traditional kimchi and identified as Leuconostoc sp. strain JYY4. Batch fermentation was conducted in bioreactor with a working volume of 3 L. The media was MMY and 15% (w/v) sucrose. Mineral medium consisted of $3.0g\;KH_2PO_4$, $0.01g\;FeSO_4$, $H_2O$, $0.01g\;MnSO_4$, $4H_2O$, $0.2g\;MgSO_4\;7H_2O$, 0.01 g NaCl, $0.05g\;CaCl_2$ per 1 liter deionized water. The pH of media was initially adjusted to 6.0. The inoculation rate was 1.0% (v/v) of the working volume. Temperature was maintained at $28^{\circ}C$. The agitation rate was 100 rpm. The production pattern of dextran was associated with the cell growth. After 24 hr dextran reached its highest concentration of 59.4 g/L. The sucrose was consumed completely after 40 hr. Growth reached stationery phase when sucrose became limiting, regardless of the presence of fructose or mannitol. When the specific growth rate was 0.54 hr-1, utilization averaged 5.8 g/L-hr. The yield and productivity of dextran were 80% and 2.0 g/L-hr, respectively. Dextrans produced by were separated to two different size by an alcohol fraction method. The size of high molecular weight dextran (45% alcohol, v/v), less soluble dextran, was between MW 500,000 and 2,000,000. Soluble dextran (55% alcohol, v/v) was between 70,000 and 150,000. The molecular weight average of total dextran (70% alcohol, v/v) was between 150,000 to 500,000. The enzymatic hydrolyzates of total dextran of ATCC 13146 showed branched dextrans by Penicillium dextranase contained of glucose, isomaltose, isomaltotriose, and isomaltooligosaccharides greater than DP4 (degree of polymerization) that had branch points. Compounds greater than DP4 were branched isomaltooligosaacharides. Hydrolysates by the Lipomyces dextranase produced the same composition of oligosaccharides as those by Penicillin dextranase.

• Korean Journal of Food Science and Technology
• /
• v.53 no.5
• /
• pp.634-639
• /
• 2021

This study investigated the effects of cold plasma (CP) treatment on the properties of biopolymer films prepared with defatted mustard meal (DMM films). CP treatments using N₂, O₂, He, Ar, and dry air did not affect the tensile properties, water vapor permeability, color, and morphology of DMM films, whereas the treatments using He and Ar improved their printability. The tensile strength (TS) of O₂- or air-CP-treated DMM films and the elastic modulus (EM) of O₂-, He-, Ar-, or air-CP-treated films were lower than those of the untreated films. An increase in the power of Ar-CP treatment resulted in an increase in EM. The optimum treatment power and time for minimizing yellowness changes by Ar-CP treatment were 420 W and 40 min, respectively. The results demonstrated the potential application of CP treatment to improve the film properties of DMM films and possibly other agricultural by-product-based biopolymer films, making the films more applicable to food packaging.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.129-129
• /
• 2016

Graphene, as a single layer of $sp^2$-bonded carbon atoms packed into a 2D honeycomb crystal lattice, has attracted much attention due to its outstanding properties. In order to synthesize high quality graphene, transition metals, such as nickel and copper, have been widely employed as catalysts, which needs transfer to desired substrates for various applications. However, the transfer steps are not only complicated but also inevitably induce defects, impurities, wrinkles, and cracks of graphene. Furthermore, the direct synthesis of graphene on dielectric surfaces has still been a premature field for practical applications. Therefore, cost effective and concise methods for transfer-free graphene are essentially required for commercialization. Here, we report a facile transfer-free graphene synthesis method through nickel and carbon co-deposited layer. In order to fabricate 100 nm thick NiC layer on the top of $SiO_2/Si$ substrates, DC reactive magnetron sputtering was performed at a gas pressure of 2 mTorr with various Ar : $CH_4$ gas flow ratio and the 200 W DC input power was applied to a Ni target at room temperature. Then, the sample was annealed under 200 sccm Ar flow and pressure of 1 Torr at $1000^{\circ}C$ for 4 min employing a rapid thermal annealing (RTA) equipment. During the RTA process, the carbon atoms diffused through the NiC layer and deposited on both sides of the NiC layer to form graphene upon cooling. The remained NiC layer was removed by using a 0.5 M $FeCl_3$ aqueous solution, and graphene was then directly obtained on $SiO_2/Si$ without any transfer process. In order to confirm the quality of resulted graphene layer, Raman spectroscopy was implemented. Raman mapping revealed that the resulted graphene was at high quality with low degree of $sp^3$-type structural defects. Additionally, sheet resistance and transmittance of the produced graphene were analyzed by a four-point probe method and UV-vis spectroscopy, respectively. This facile non-transfer process would consequently facilitate the future graphene research and industrial applications.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.463-463
• /
• 2014

Dye-sensitized solar cells (DSSCs) have generated a strong interest in the development of solid-state devices owing to their low cost and simple preparation procedures. Effort has been devoted to the study of electrolytes that allow light-to-electrical power conversion for DSSC applications. Several attempts have been made to substitute the liquid electrolyte in the original solar cells by using (2,2',7,7'-tetrakis (N,N-di-p-methoxyphenylamine)-9-9'-spirobi-fluorene (spiro-OMeTAD) that act as hole conductor [1]. Although efficiencies above 3% have been reached by several groups, here the major challenging is limited photoelectrode thickness ($2{\mu}m$), which is very low due to electron diffusion length (Ln) for spiro-OMeTAD ($4.4{\mu}m$) [2]. In principle, the $TiO_2$ layer can be thicker than had been thought previously. This has important implications for the design of high-efficiency solid-state DSSCs. In the present study, we have fabricated 3-D Transparent Conducting Oxide (TCO) by growing tin-doped indium oxide (ITO) nanowire (NWs) arrays via a vapor transport method [3] and mesoporous $TiO_2$ nanoparticle (NP)-based photoelectrodes were prepared using doctor blade method. Finally optimized light-harvesting solid-state DSSCs is made using 3-D TCO where electron life time is controlled the recombination rate through fast charge collection and also ITO NWs length can be controlled in the range of over $2{\mu}m$ and has been characterized using field emission scanning electron microscopy (FE-SEM). Structural analyses by high-resolution transmission electron microscopy (HRTEM) and X-Ray diffraction (XRD) results reveal that the ITO NWs formed single crystal oriented [100] direction. Also to compare the charge collection properties of conventional NPs based solid-state DSSCs with ITO NWs based solid-state DSSCs, we have studied intensity modulated photovoltage spectroscopy (IMVS), intensity modulated photocurrent spectroscopy (IMPS) and transient open circuit voltages. As a result, above $4{\mu}m$ thick ITO NWs based photoelectrodes with Z907 dye shown the best performing device, exhibiting a short-circuit current density of 7.21 mA cm-2 under simulated solar emission of 100 mW cm-2 associated with an overall power conversion efficiency of 2.80 %. Finally, we achieved the efficiency of 7.5% by applying a CH3NH3PbI3 perovskite sensitizer.

• Tuberculosis and Respiratory Diseases
• /
• v.50 no.4
• /
• pp.415-425
• /
• 2001

Background : The correlation between the high resolution computed tomography(HRCT) emphysema score and the physiologic parameters including resting and exercise pulmonary function test was investigated in 14 patients($60.6{\pm}10.3$ years) with pulmonary emphysema. Methods : The patients underwent a HRCT, a resting pulmonary function test, and incremental exercise testing(cycle ergometer, 10 W/min). Computed tomography scans were obtained on a GE highlight at 10 mm intervals using 10 mm collimation, from the apex to the base after a full inspiration. The emphysema scores were determined by a CT program 'Density mask' outlining the areas with attenuation values less than -900 HU, indicating the emphysema areas, and providing an overall percentage of lung involvement by emphysema. Results : Among the resting PFT parameters, only the diffusing capacity(r=-0.75) and $PaO_2$ (r=-0.66) correlated with the emphysema score(p<0.05). Among the exercise test parameters, the emphysema score correlated significantly with the maximum power(r=-0.74), maximum oxygen consumption(r=-0.68), anaerobic threshold(V-slope method: r=-0.69), maximal $O_2$-pulse(r=-0.73), and the physiologic dead space ratio at the maximum workload(r=-0.80)(p<0.01). Conclusion: We could find that exercise testing parameters showed a much better correlation with the HRCT emphysema score, which is known to have a good correlation with the pathologic severity than the resting PIT parameters. Therefore it is suggested that exercise testing is superior to resting PIT for estimating in the estimation of the physiologic disturbance in emphysema patients.