• Journal of the Society of Naval Architects of Korea
• /
• v.45 no.6
• /
• pp.631-636
• /
• 2008

In this paper, numerical analysis based on the RANS equation and the Realizable ${\kappa}-{\varepsilon}$ turbulence model is carried out for flows around an axisymmetric body at three Reynolds numbers($1.22{\times}10^7$, $1.0{\times}10^8$, $1.5{\times}10^8$) and the numerical results are compared with experiments data. Computed velocity distributions agree well with experiments as the Reynolds number increases. Pressure distributions agree well with the results of the potential flow except the tail region but differ from experiments for the parallel middle body as well as tail region. Pressure gradients show a good agreement with those of potential flow and experiment except the tail region. Friction coefficients show that the numerical results generally are lower than the experimental results estimated from the measured velocity. The difference of friction coefficients between the calculation and the experiment increases with growing of a boundary layer.

• Steel and Composite Structures
• /
• v.31 no.2
• /
• pp.201-216
• /
• 2019

This scientific paper provides a theoretical, numerical and experimental analysis of local stability of axially compressed columns made of thin-walled rectangular concrete-filled steel tubes (CFSTs), with the consideration of initial geometric imperfections. The work presented introduces the theory of elastic critical stresses in local buckling of rectangular wall members under uniform compression. Moreover, a numerical calculation method for the determination of the critical stress coefficient is presented, using a differential equation for a slender wall with a variety of boundary conditions. For comparison of the results of the numerical analysis with those collected by experiments, a new model is created to study the behaviour of the composite members in question by means of the ABAQUS computational-graphical software whose principles are based on the finite element method (FEM). In modelling the analysed members, the actual boundary and loading conditions and real material properties are taken into account, obtained from the experiments and material tests on these members. Finally, the results of experiments on such members are analysed and then compared with the numerical values. In conclusion, several recommendations for the design of axially compressed composite columns made of rectangular concrete-filled thin-walled steel tubes are suggested as a result of this comparison.

• Progress in Superconductivity and Cryogenics
• /
• v.20 no.3
• /
• pp.21-27
• /
• 2018

It is difficult to fabricate and maintain moving parts of expander at cryogenic temperature. This paper describes numerical analysis and experimental investigation on a cryogenic reciprocating expander without moving piston. An intake valve which takes high-pressure gas, and an exhaust valve which discharges low-pressure gas, are connected to a tube. The inside pressure of the tube is pulsated for work production. This geometric configuration is similar to that of pulse tube refrigerator but without regenerator. An orifice valve and a reservoir are installed to control the phase of the mass flow and the pressure. At the warm end, a heat exchanger rejects the heat which is converted from the produced work of the expanded gas. For the numerical analysis, mass conservation, energy conservation, and local mass function for valves are used as the governing equations. Before performing cryogenic experiments, we carried out the expander test at room temperature and compared the performance results with the numerical results. For cryogenic experiments, the gas is pre-cooled by liquid nitrogen, and then it enters the pulse tube expander. The experiments are controlled by the opening of the orifice valve. Numerical analysis also found the expander conditions that optimize the expander performance by changing the intake pressure and valve timing as well as the opening of the orifice valve. This paper discusses the experimental data and the numerical analysis results to understand the fundamental behavior of such a newly developed non-mechanical expander and elucidate its potential feature for cryogenic application.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.23 no.3
• /
• pp.248-257
• /
• 2011

In the present study, we proposed a new numerical wave tank model to analyze the vertical tension-leg circular floating bodies, using a 2-D Navier-Stokes solver. An IBM(Immersed Boundary Method) capable of handling interactions between waves and moving structures with complex geometry on a standard regular Cartesian grid system is coupled to the VOF(Volume of Fluid) method for tracking the free surface. Present numerical results for the motions of the floating body were compared with existing experimental data as well as numerical results based on FAVOR(Fractional Area Volume Obstacle Representation) algorithm. For detailed examinations of the present model, the additional hydraulic experiments for floating motions and free surface transformations were conducted. Further, the versatility of the proposed numerical model was verified via the numerical and physical experiments for the general rectangular floating bodies. Numerical results were compared with experiments and good agreement was archived.

• The KSFM Journal of Fluid Machinery
• /
• v.11 no.5
• /
• pp.7-14
• /
• 2008

Open channel type regenerative pump has been used in various industrial fields. It generates high pressure with low flow rate. However, it has low efficiency because of its complex flow pattern, We studied performance experiments and 3D numerical flow analysis of a regenerative pump. Through the numerical analysis, we could get the internal flow pattern and profile of a regenerative pump. Also, we examined leakage flow effects due to the gap between casing and impeller and stripper clearance. For the numerical analysis verification, we performed experiments and they had similar tendency at the design point.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2004.05a
• /
• pp.263-267
• /
• 2004

This paper presents a comparative study on numerical and wave-maker generated waves. The wave-makers employed to carry out the experiments have mathematical forms. The linear and quadratic models were tested. When it comes numerical analysis, the authors used the FLUENT which is widely used commercial code. Only two dimensional cases were considered. The experiments were done in a small wave flume. The waves were generated for various frequencies to examine the characteristics of the water waves. The comparison of the numerical and wave-maker generated waves were made.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.592-597
• /
• 2001

An automobile lower arm has been fabricated in a prototype form by hydroforming with the aids of numerical analysis and experiments. For the numerical process design, a program called HydroFORM-3D developed here on the basis of a rigid-plastic model, has been applied to the lower arm hydroforming. The friction calculation between die and workpiece has been dealt carefully by introducing a new scheme in three-dimensional surface integration. To accomplish successful hydroforming process design, thorough investigation on proper combination of process parameters such as internal hydraulic pressure, axial feeding, and tool geometry has been performed. Results obtained from numerical simulation for a lower arm in hydroforming process are compared with a series of experiments. The comparison shows that the numerical analysis successfully provides the manufacturing information on the lower arm hydroforming, and it predicts the geometrical deformation and the thinning.

• Journal of Ocean Engineering and Technology
• /
• v.20 no.5 s.72
• /
• pp.23-29
• /
• 2006

A quasi depth-varying mathematical model for wind-generated circulation in coastal areas, expressed in terms of the depth-averaged horizontal velocity components and free surface elevation was validated and used to understand the diurnal circulation process. The wind velocity is considered as a dominant factor for driving the current. In this paper, three-dimensional numerical experiments that included the land topography were used to investigate the mesoscale air flaw over the coastal regions. The surface temperature of the inland area was determined through a surface heat budget consideration with the inclusion of a layer of vegetation.A series of numerical experiments were then carried out to investigate the diurnal response of the air flaw and wind-generated circulation to various types of surface inhomogeneities.

• Journal of Ocean Engineering and Technology
• /
• v.14 no.3
• /
• pp.46-54
• /
• 2000

Three dimensional numerical experiments that included the land-use transformation by the large scale reclamation were used to investigate the mesoscale air flow over the coastal regions. In this paper the surface temperature of the inland was determined through the surface heat budget consideration with inclusion of a layer of vegetation. The vertical diffusion coefficients of momentum, heat and specific humidity in the constant flux layer were taken from the Mellor and Yamada(1975). It has shown that the resulting model is able to reproduce the air circulation in coastal regions, and the simulated characteristics agree with the known properties of this circulation. A series of numerical experiments were then carried out to investigate the diurnal response of the air flow to various types of surface inhomogeneities.

• Journal of Ocean Engineering and Technology
• /
• v.27 no.1
• /
• pp.16-23
• /
• 2013

By carrying out numerical analyses and model experiments, this paper presents the attenuation characterization of an L(0,2) guided ultrasonic wave propagating in a buried steel pipe. From this investigation, we first find that the L(0,2) mode has a better attenuation property. Second, it is shown from the numerical analyses that the attenuation increases with increases in the soil embedment length (0, 500, 1000, and 1500 mm) and degrees of saturation (0, 50, 99, and 100%). Third, it is also shown from the model experiment that the attenuation increases as the embedment lengths and soil moisture quantities (0, 10, 20, and 30 kg) increase. Finally, we find that an exponential extrapolation gives a better attenuation prediction because the extrapolation gives similar attenuation patterns between the numerical and experimental results.