• Journal of Radiation Protection and Research
• /
• v.24 no.2
• /
• pp.73-86
• /
• 1999

The ion-exchange method for the purification of primary coolant has been used broadly in PWR(pressurized water reactor)-type nuclear power plants due to its high decontamination efficiency, simple system, and easy operation. However, its non-selective removal of metal and non-radionuclides shortens its life, resulting in the generation of a large amount of waste ion-exchange resin. In this study, the feasibility of electrodeionization (EDI) was investigated for the purification of primary cooling water using synthetic solutions under various experimental conditions as an alternative method for the ion exchange. The results shows that as the feed flow-rate increased, the removal efficiency increased and the power consumption decreased. The removal rate was observed as a 1000 decontamination factor(DF) at a nearly constant level. For the synthetic solution of 3 ppm TDS (Total Dissolved Solid), the power consumption was 40.3 mWh/L at 2.0 L/min of feed flow rate. The higher removal rate of metal species and lower power consumption were obtained with greater resin volume per diluting compartment. However, the flow rate of the EDI process decreased with the elapsed time because of the hydrodynamic resistivity of resin itself and resin fouling by suspended solids. Thus, the ion-exchange resin was replaced by an ion-conducting spacer in order to overcome the drawback. The system equipped with the ion-conducting spacer resolved the problem of the decreasing flow rate but showed a lower efficiency in terms of the power consumption, the removal rate of metal species and current efficiency. In the repeated batch operation, it was found that the removal efficiency of metal species was stably maintained at DF 1000.

• Journal of Adhesion and Interface
• /
• v.19 no.3
• /
• pp.113-117
• /
• 2018

Boron carbide is lower in hardness than diamond or boron nitride but has a hardness of more than 30 GPa and is used for manufacturing tank armors and ammo shells due to its high hardness. It is also used as a neutron absorber due to its ability to absorb neutrons, which is increasing its use in nuclear power projects. Neutrons have no interaction with electrons and are known to pass through the material without interactions. Along with boron carbide, the atoms with high interaction with neutrons are hydrogen, and high hydrogen concentration polyesters and epoxy polymers including boron are used as materials for manufacturing products for nuclear power generation waste. In this paper, the surface of boron carbide is treated with iron oxide and tungsten to improve interaction between modified boron carbide and epoxy polymer. XRD and XPS were used to confirm that iron oxide and tungsten are well attached on the surface of boron carbide, respectively. The mechanical strength of the surface treated boron carbide was measured by a universal testing machine (UTM) and the dynamic characteristics of the cured product were observed by using a dynamic analyzer (DMA).

• Nuclear Engineering and Technology
• /
• v.25 no.4
• /
• pp.539-547
• /
• 1993

A stochastic approach using continuous time Markov process is presented to model the one-dimensional nuclide transport in fractured rock media as a further extension for previous works［1-3］. Nuclide transport of decay chain of arbitrary length in the single planar fractured rock media in the vicinity of the radioactive waste repository is modeled using a continuous time Markov process. While most of analytical solutions for nuclide transport of decay chain deal with the limited length of decay chain, do not consider the case of having rock matrix diffusion, and have very complicated solution form, the present model offers rather a simplified solution in the form of expectance and its variance resulted from a stochastic modeling. As another deterministic way, even numerical models of decay chain transport, in most cases, show very complicated procedure to get the solution and large discrepancy for the exact solution as opposed to the stochastic model developed in this study. To demonstrate the use of the present model and to verify the model by comparing with the deterministic model, a specific illustration was made for the transport of a chain of three member in single fractured rock medium with constant groundwater flow rate in the fracture, which ignores the rock matrix diffusion and shows good capability to model the fractured media around the repository.

• Journal of the Korean Chemical Society
• /
• v.37 no.9
• /
• pp.813-819
• /
• 1993

An ICP-AES system directly connected with a separation column was used in order to determine the trace elements in $UO_2$ powder promptly and reduce the volume of the waste solution. The outlet of a separation column, which was filled with Teflon powder ($330\;{\mu}m$) coated with tri-n-butyl phosphate (TBP) as extractant, was directly connected with sample injection tube of ICP-AES. Eleven elements including molybdenum in $UO_2$ powder were separated and determined simultaneously. Recoveries of these elements were $91{\sim}110%$ and these results were agreed with those of solvent extraction methods. This method was applicable to quality control in manufacturing nuclear fuel.

• Carbon letters
• /
• v.22
• /
• pp.81-88
• /
• 2017

In the present study, biomass-based lignin was extracted from industrial waste black liquor and the extracted lignin was characterized by means of attenuated total reflectance-Fourier transform infrared spectroscopy and $^1H-nuclear$ magnetic resonance spectroscopy. The extracted lignin was carbonized at different temperatures and then activated with steam at $850^{\circ}C$. The extracted lignin in powder state was transformed into a bulky carbonized lignin due to possible fusion between the lignin particles occurring upon carbonization. The carbonized and then pulverized lignin exhibits brittle surfaces, the increased thermal stability, and the carbon assay with increasing the carbonization temperature. The scanning electron microscopic images and the Brunauer-Emmett-Teller result indicate that the steam-activated carbon has the specific surface area of $1718m^2/g$, which is markedly greater than the carbonized lignin. This study reveals that biomass-based activated carbon with highly porous structure can be produced from costless black liquor via steam-activation process.

• Annals of Clinical Neurophysiology
• /
• v.6 no.2
• /
• pp.65-74
• /
• 2004

Limb-girdle muscular dystrophy (LGMD) is a heterogeneous group of inherited muscle disorders caused by the mutations of different genes encoding muscle proteins. In the past, when the molecular diagnostic techniques were not available, the subtypes of muscular dystrophies were classified by the pattern of muscle weakness and the mode of inheritance, and LGMD had been considered as a 'waste basket' of muscular dystrophy because many unrelated heterogeneous cases with 'limb-girdle' weakness were put into the category of LGMD. With the advent of molecular genetics at the end of the last century, it has been known that there are many subtypes of LGMD caused by the mutation of different genes, and now, LGMD is classified according to the results of the linkage analysis and the genes or proteins affected. Only small proportion (probably less than 10%) of LGMD is dominantly inherited, and autosomal dominant LGMD (AD-LGMD) consists of six subtypes (LGMD1A to 1F) so far. In autosomal recessive LGMD (AR-LGMD), more than 10 subtypes (LGMD2A to 2J) have been linked and most of the causative genes have been identified. Among AR-LGMDs, LGMD2A (calpain 3 deficiency), 2B (dysferlin deficiency), and sarcoglycanopathy (LGMD2C-2F) are major subtypes. The defective proteins in LGMDs are components of nuclear envelope, cytosol, sarcomere, or sarcolemma, and seem to play a different role in the pathogenesis of muscular dystrophy. It is notable that many causative genes of LGMDs are also responsible for other categories of muscular dystrophy or diseases affecting other tissue. However, by which mechanism they produce such a broad phenotypic variability is still unknown. The identification of mutation in the relevant gene is confirmative for the diagnosis, and is essential for genetic counseling and antenatal diagnosis of LGMD. Because many different genes are responsible for LGMD, differentiation of subtypes using immunohistochemistry and western blotting is the essential step toward the detection of mutation. For the effective research and medical care of the patients with muscular dystrophy in Korea, a research center with a medical facility supported by the government seems to be needed.

• Journal of the Korean Geotechnical Society
• /
• v.21 no.4
• /
• pp.41-49
• /
• 2005

Recently, ground has been often exposed to high temperature environments such as chemical ground improvement, thermal energy storage system, and underground nuclear waste disposal system. Since the behavior of clay is sensitive to temperature change, the studies on the engineering properties of clay subjected to high temperature history may be important. This paper presents the mechanical behavior of clay with high temperature condition. $\bar{CU}$ tests using a high temperature and pressure triaxial compression test apparatus were carried out in order to investigate characteristics of deformation, shear strength, compression and consolidation of clay. During tests, the temperature was varied from $20^{\circ}C,\;50^{\circ}C,\;75^{\circ}C,\;80^{\circ}C\;to\;100^{\circ}C$.

• Tribology and Lubricants
• /
• v.31 no.5
• /
• pp.195-204
• /
• 2015

Several researches are focused on improving the value of fine chemicals based on biomass resources due to environmental and other concerns associated with the use of petroleum-based products. Therefore, the synthesis and application of estolides derived from plant-based waste oil materials and their application as lubricants and as processing oil for butyl rubber products have been studied. Four kinds of estolide were prepared with conversions of 71~92% over 24h using various vegetable oils, as determined by size exclusion chromatography (SEC) and nuclear magnetic resonance (NMR) spectroscopy. FT-IR spectroscopy determines the esterification of estolides using 2-ethylhexyl alcohol. The estolides have iodine values of 35~90, α-ester/α-acid ratios of 0.45~0.55, and total acid number of 114~134 mg KOH g^–1. Four ball wear tests show that the wear scar diameters (WSDs) of estolides as base oil significantly decreased to 0.328~0.494 mm, compared to WSDs of 0.735 and 0.810 mm of WSD for 150N and Yubase 6, respectively, as general base oil. Thus, the estolides have better wear resistance and satisfying design objectives for the engineering of a variety of lubricant base oils.

• The Journal of the Korea Contents Association
• /
• v.16 no.5
• /
• pp.660-667
• /
• 2016

Conventional decontamination methods utilize water-based systems, which generate high amounts of secondary wastes. Herein, we describe an environmentally benign decontamination method using liquid and supercritical $CO_2$. The use of $CO_2$ as a solvent affords effective waste reduction by its ability to be recycled, thereby leaving be hind only the contaminants upon its evaporation. In this study, a $CO_2$ solution process was assessed using t-salen(t-butylsalen), DC18C6 (dicyclohexano-18Crown6), 8-HQN(8-hydroxyquinoline), NEt4PFOSA(perfluoro-1-octanesulfonic acid tetra-ethyl ammonium salt), and NEt4PFOA(pentadecafluorooctanoic acid ammonium salt) to extract spiked radioactive contaminants(Nb,Zr,Co,Sr) from an inert sample matrix, namely filter paper. With the static extraction method, Sr was extracted with a maximum extraction rate of 97%, and Nb was extracted with a maximum extraction rate of 75%. Additionally, we were also able to extract Co and Zr with maximum extract ion ratesof 73% and 64%, respectively.

• Tunnel and Underground Space
• /
• v.21 no.2
• /
• pp.117-127
• /
• 2011

The purpose of this study is to demonstrate the effect of in-situ rock stresses on the deformability and permeability of fractured rocks. Geological data were taken from the site investigation at Forsmark, Sweden, conducted by Swedish Nuclear Fuel and Waste Man-agement Company (SKB). A set of numerical experiments was conducted to determine the equivalent mechanical properties (essentially, elastic moduli and Poisson's ratio) and permeability, using a Discrete Fracture Network-Discrete Element Method (DFN-DEM) approach. The results show that both mechanical properties and permeability are highly dependent on stress because of the hyperbolic nature of the stiffness of fractures, different closure behavior of fractures, and change of fluid pathways caused by deformation. This study shows that proper characterization and consideration of in-situ stress are important not only for boundary conditions of a selected site but also for the understanding of the mechanical and hydraulic behavior of fractured rocks.