• Nuclear Engineering and Technology
• /
• 제39권4호
• /
• pp.287-298
• /
• 2007

As part of the $AP1000^{TM}$ pressurized water reactor design certification program, a series of integral systems tests of the nuclear steam supply system was performed at the APEX-1000 test facility at Oregon State University. These tests provided data necessary to validate Westinghouse safety analysis computer codes for AP1000 applications. In addition, the tests provided the opportunity to investigate the thermal-hydraulic phenomena expected to be important in AP1000 small-break loss of coolant accidents (SBLOCAs). The APEX-1000 facility is a 1/4-scale pressure and 1/4-scale height simulation of the AP1000 nuclear steam supply system and passive safety features. A series of eleven tests was performed in the APEX-1000 facility as part of a U.S. Department of Energy contract. In all, four SBLOCA tests representing a spectrum of break sizes and locations were simulated along with tests to study specific phenomena of interest. The focus of this paper is the SBLOCA tests. The key thermal-hydraulic phenomena simulated in the APEX-1000 tests, and the performance and interactions of the passive safety-related systems that can be investigated through the APEX-1000 facility, are emphasized. The APEX-1000 tests demonstrate that the AP1000 passive safety-related systems successfully combine to provide a continuous removal of core decay heat and the reactor core remains covered with considerable margin for all small-break LOCA events.

• Nuclear Engineering and Technology
• /
• 제45권4호
• /
• pp.489-504
• /
• 2013

Software safety for nuclear reactor protection systems (RPSs) is the most important requirement for the obtainment of permission for operation and export from government authorities, which is why it should be managed with well-experienced software development processes. The RPS software is typically modeled with function block diagrams (FBDs) in the design phase, and then mechanically translated into C programs in the implementation phase, which is finally compiled into executable machine codes and loaded on RPS hardware - PLC (Programmable Logic Controller). Whereas C Compilers are fully-verified COTS (Commercial Off-The-Shelf) software, translators from FBDs to C programs are provided by PLC vendors. Long-term experience, experiments and simulations have validated their correctness and function safety. This paper proposes a behavior-preserving translation from FBD design to C implementation for RPS software. It includes two sets of translation algorithms and rules as well as a prototype translator. We used an example of RPS software in a Korean nuclear power plant to demonstrate the correctness and effectiveness of the proposed translation.

• Nuclear Engineering and Technology
• /
• 제45권4호
• /
• pp.439-458
• /
• 2013

REX-10 is a fully-passive small modular reactor in which the coolant flow is driven by natural circulation, the RCS is pressurized by a steam-gas pressurizer, and the decay heat is removed by the PRHRS. To confirm design decisions and analyze the transient responses of an integral PWR such as REX-10, a thermal-hydraulic system code named TAPINS (Thermal-hydraulic Analysis Program for INtegral reactor System) is developed in this study. Based on a one-dimensional four-equation drift-flux model, TAPINS incorporates mathematical models for the core, the helical-coil steam generator, and the steam-gas pressurizer. The system of difference equations derived from the semi-implicit finite-difference scheme is numerically solved by the Newton Block Gauss Seidel (NBGS) method. TAPINS is characterized by applicability to transients with non-equilibrium effects, better prediction of the transient behavior of a pressurizer containing non-condensable gas, and code assessment by using the experimental data from the autonomous integral effect tests in the RTF (REX-10 Test Facility). Details on the hydrodynamic models as well as a part of validation results that reveal the features of TAPINS are presented in this paper.

• Nuclear Engineering and Technology
• /
• 제53권10호
• /
• pp.3449-3459
• /
• 2021

With the increasing availability of high-performance computing (HPC) platforms, uncertainty quantification (UQ) and sensitivity analyses (SA) can be efficiently leveraged to optimize design parameters of complex engineering problems using modeling and simulation tools. The workflow involved in such studies heavily relies on HPC resources and hence requires pre-processing and post-processing capabilities of large amounts of data along with remote submission capabilities. The NEAMS Workbench addresses all aspects of the workflows involved in these studies by relying on a user-friendly graphical user interface and a python application program interface. This paper highlights the NEAMS Workbench capabilities by presenting a semiautomated coupling scheme between Dakota and any given package integrated with the NEAMS Workbench, yielding a simplified workflow for users. This new capability is demonstrated by running a SA of a turbulent flow in a pipe using the open-source Nek5000 CFD code. A total of 54 jobs were run on a HPC platform using the remote capabilities of the NEAMS Workbench. The results demonstrate that the semiautomated coupling scheme involving Dakota can be efficiently used for UQ and SA while keeping scripting tasks to a minimum for users. All input and output files used in this work are available in https://code.ornl.gov/neams-workbench/dakota-nek5000-study.

• Nuclear Engineering and Technology
• /
• 제51권6호
• /
• pp.1525-1531
• /
• 2019

The indigenous nuclear power program of India is based mainly on a series of Pressurised Heavy Water Reactors (PHWRs). A burst correlation for Indian PHWR fuel claddings has been developed and empirical burst parameters are determined. The burst correlation is developed from data available in literature for single-rod transient burst tests performed on Indian PHWR claddings in inert environment. The heating rate and internal overpressure were in the range of 7 K/s-73 K/s and 3 bar-80 bar, respectively, during the burst tests. A burst criterion for inert environment, which assumes that deformation is controlled by steady state creep, has been developed using the empirical burst parameters. The burst criterion has been validated with experimental data reported in literature and the prediction of burst parameters is in a fairly good agreement with the experimental data. The burst criterion model reveals that increasing the heating rate increases the burst temperature. However, at higher heating rates, burst strain is decreased considerably and an early rupture of the claddings without undergoing considerable ballooning is observed. It is also found that the degree of anisotropy has significant influence on the burst temperature and burst strain. With increasing degree of anisotropy, the burst temperature for claddings increases but there is a decrease in the burst strain. The effect of anisotropy in the ${\alpha}$-phase is carried over to ${\alpha}+{\beta}$-phase and its effect on the burst strain in the ${\alpha}+{\beta}$-phase too can be observed.

• Nuclear Engineering and Technology
• /
• 제53권11호
• /
• pp.3816-3823
• /
• 2021

The mechanical features evaluated theoretically using Makishima-Mackenzie's model for glasses xBaO-(50-x) PbO-50P₂O₅ where x = 0, 5, 10, 15, 20, 30, 40, and 50 mol%. Wherefore, the elastic characteristics; Young's, bulk, shear, and longitudinal modulus calculated. The obtained result showed an increase in the calculated values of elastic moduli with the replacement of the PbO by BaO contents. Moreover, the Poisson ratio, micro-hardness, and the softening temperature calculated for the investigated glasses. Besides, gamma and neutron shielding ability evaluated for the barium doped lead phosphate glasses. Monte Caro code (MCNP-5) and the Phy-X/PSD program applied to estimate the mass attenuation coefficient of the studied glasses. The decrease in the PbO ratio has a negative effect on the MAC. The highest MAC decreased from 65.896 cm²/g to 32.711 cm²/g at 0.015 MeV for BPP0 and BPP7, respectively. The calculated values of EBF and EABF showed that replacement of PbO with BaO contents in the studied BPP glasses helps to reduce the number of photons accumulated inside the studied BPP glasses.

• Nuclear Engineering and Technology
• /
• 제55권9호
• /
• pp.3401-3408
• /
• 2023

In this study, we used the Monte Carlo N-Particle program to simulate the gamma-ray spectra obtained from plastic scintillators holes filled with bismuth nanoparticles. We confirmed that the incorporation of bismuth nanoparticles into a plastic scintillator enhances its performance for gamma-ray spectroscopy using the subtraction method. The subtracted energy spectra obtained from the bismuth-nanoparticle-incorporated and the original plastic scintillator exhibit a distinct energy peak that does not appear in the corresponding original spectra. We varied the diameter and depth of the bismuth-filled holes to determine the optimal hole design for gamma-ray spectroscopy using the subtraction method. We evaluated the energy resolutions of the energy peaks in the gamma-ray spectra to estimate the effects of the bismuth nanoparticles and determine their optimum volume in the plastic scintillator. In addition, we calculated the peak-to-total ratio of the energy spectrum to evaluate the energy measuring limit of the bismuth nanoparticle-containing plastic scintillator using the subtraction method.

• 대한기계학회논문집A
• /
• 제39권3호
• /
• pp.249-257
• /
• 2015

원자력 발전소의 반응로에는 핵분열 에너지를 생성하고 방사성 물질의 유출을 막는 핵연료 집합체가 있으며, 이러한 집합체는 핵연료와 피복관으로 구성되어 있는 핵 연료봉으로 구성되어 있다. 원자로에서 핵연료봉 거동의 안전성을 평가하기 위해 해석적인 방법을 적용하며 이러한 평가 코드를 핵 연료 성능 코드라 한다. 경수로 핵연료 해석에서는 간극의 두께에 따라 열전도도가 크게 영향을 받는 간극 열전도도가 주요 거동해석에 영향을 미친다. 본 연구에서는 간극 두께에 따라 열전도도가 변화하는 3 차원 간극 요소(Gap element)를 제안하였으며, 이를 적용하기 위해 3 차원 열탄성 모듈을 FORTRAN90을 이용하여 개발하였다. 제안된 3 차원 간극 요소를 이용하여 핵 연료봉에서 발생할 수 있는 비대칭적인 형상인 핵 연료 표면에 결함이 생긴 경우 MPS(Missing Pellet Surface)와 핵연료봉의 편심(Eccentricity of the nuclear fuel rod) 형상에 대하여 3 차원 해석을 진행하였다.

• 핵의학기술
• /
• 제16권1호
• /
• pp.108-114
• /
• 2012

면역측정법을 이용하는 검사실에서 가장 많이 사용하고 있는 상업용 제3자 정도관리물질이 BIO-RAD사에서 제공하는 물질이다. 현재 BIO-RAD 정도관리 물질에 포함된 Reference Sheet에는 비방사면역측정을 이용한 검사방법과 검사장비별로 각 측정물질의 Acceptable Range가 기재되어 있다. 그러나 방사면역측정법을 이용하여 검사하는 측정kit나 기기에 대해서는 실무에 적용할 만한 Acceptable Range에 대한 언급이 다소 부족한 것이 현실이다. 방사면역측정검사에 대한 Acceptable Range를 설정하여 검사결과의 객관성을 높이고 누적된 데이터를 제조사에 권고하여 발행되는 Reference Sheet에 기재하고자 한다. 본원에서는 2009년부터 부분적으로 BIO-RAD 정도관리 물질을 사용하여 2011년에는 일부 특정 항목을 제외한 대부분의 검사종목에 BIO-RAD 제 3자 정도관리물질을 사용하고 있다. 따라서 측정된 내부정도관리 데이터를 BIO-RAD사의 Unity Real Time program (version 1.0.9.27)을 이용하여 Acceptable Range를 설정하였다. BIO-RAD 정도관리 물질을 사용하는 약 50가지 검사종목의 20개 Point Data의 평균값, 표준편차, 변이계수를 구하여 측정kit별 Acceptable Range를 산출하였으며, 자동화 면역 측정기기인 Roche Elecsys/ E170/ cobas e Systems의 측정값과 비교하였다. 현재 시행하고 있는 외부정도관리 프로그램과 같이 BIO-RAD 정도관리 물질을 공통으로 사용하는 병원과 peer group을 설정하여 측정 kit별, 기기별 Acceptable Range를 제조사에 권고하여 Reference Sheet에 방사면역검사실에 적합한 Acceptable Range를 기재하여 검사결과의 객관성을 높이고 국내외적으로 방사면역측정법에 대한 인지도를 높이고자 한다.

• Journal of Radiation Protection and Research
• /
• 제41권3호
• /
• pp.196-205
• /
• 2016

Background: The emergency planning zone (EPZ) of the city of Busan is divided into the precautionary actions zone (PAZ) and the urgent protective action planning zone; which have a 5-km radius and a 20-km to 21-km radius from the nuclear power plant site, respectively. In this study, we assumed that a severe accident occurred at Shin-Kori nuclear unit 3 and evaluated the dispersion speed of radiological material at each distance at various wind speeds, and estimated the effective dose equivalent and the evacuation time of PAZ residents with the goal of supporting off-site emergency action planning for the nuclear site. Materials and Methods: The total effective dose equivalent, which shows the effect of released radioactive materials on the residents, was evaluated using the RASCAL 4.2 program. In addition, a survey of 1,036 residents was performed using a standardized questionnaire, and the resident evacuation time according to road and distance was analyzed using the VISSIM 6.0 program. Results and Discussion: According to the results obtained using the VISSIM and RASCAL programs, it would take approximately 80 to 252.2 minutes for permanent residents to move out of the PAZ boundary, 40 to 197.2 minutes for students, 60 to 232.2 minutes for the infirm, such as elderly people and those in a nursing home or hospital, and 30 to 182.2 minutes for those temporarily within the area. Consequently, in the event of any delay in the evacuation, it is estimated that the residents would be exposed to up to $10mSv{\cdot}h^{-1}$ of radiation at the Exclusion Area Boundaries (EAB) boundary and $4-6mSv{\cdot}h^{-1}$ at the PAZ boundary. Conclusion: It was shown that the evacuation time for the residents is adequate in light of the time lapse from the initial moment of a severe accident to the radiation release. However, in order to minimize the evacuation time, it is necessary to maintain a system of close collaboration to avoid traffic congestion and spontaneous evacuation attempts.