• Nuclear Engineering and Technology
• /
• 제36권2호
• /
• pp.165-174
• /
• 2004

The distributed resistance model has been recently implemented into the MATRA-LMR code in order to improve its prediction capability over the wire-wrap model for a flow blockage analysis in the LMR. The code capability has been investigated using experimental data observed in the FFM (Fuel Failure Mock-up)-2A and 5B for two typical flow conditions in a blocked channel. The predicted results by the MATRA-LMR with a distributed resistance model agreed well with the experimental data for wire-wrapped subchannels. However, it is suggested that the parameter n in the distributed resistance model needs to be calibrated accurately for a reasonable prediction of the temperature field under a low flow condition. Finally, the analyses of a blockage for the assembly of the KALIMER design are performed. Satisfactory results by the MATRA-LMR code were obtained through and rerified a comparison with results of the SABRE code.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1996년도 춘계학술발표회논문집(1)
• /
• pp.197-201
• /
• 1996

In the detail reaction-rate measurements in a critical assembly using the foil activation method, the measured activations of detector foils have inevitably errors caused by detector foil self-shielding effect. If neutron flux could be approximated to Westcott flux: i.e. well thermalized Maxwellian distribution, these activations of detector foil could be corrected to represent the unperturbated flux at any detected position in the cell with using Westcott option and reaction-rate option of the lattice code, WIMS-AECL. These calculated detector material self-shielding correction factors of the tested fuel, CANFLEX provided much information about neutron spectrum of test lattice cell as well as the correction factors themselves. The results could be verified by another lattice calculations.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1997년도 춘계학술발표회논문집(2)
• /
• pp.46-51
• /
• 1997

최근 경수로 핵연료 손상 원인 중의 하나인 연료봉 마모(Fretting Wear)가 지지격자의 스프링력 저하뿐만 아니라 원자로 냉각재 유동에 기인한 집합체 진동(Self-excited Fuel Assembly Vibration)에 의해 유발될 수 있는 것으로 밝혀져 해외 연료공급자들은 새로운 연료개발시 집합체 유동시험을 수행하여 냉각재 유동에 의한 집합체 진동 여부를 확인하고 있다. 본 연구에서는 경수로 핵연료집합체에 대한 모드해석 및 진동시험으로부터 고유진동수 및 진동모드형태를 구하여 모의 집합체 유동시험 결과와 비교 평가하였고 냉각재 유동에 의해 과도한 집합체 진동이 발생됨을 확인하였으며 가연성흡수봉집합체를 삽입한 경우에 대한 유동시험 결과와도 비교하였다. 또한, 이들 집합체의 진동 변위량과 손상 연료의 마모량 분포의 상관성을 비교 평가하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.291-295
• /
• 2007

FTL(Fuel Test Loop) is a facility that confirms performance of nuclear fuel at a similar irradiation condition with that of nuclear power plant. FTL consists of In-Pile Test Section (IPS) and Out-Pile System (OPS). FTL construction work began on August, 2006 and ended on March, 2007. During Construction, ensuring the worker's safety was the top priority and installation of the FTL without hampering the integrity of the HANARO was the next one. Task Force Team was organized to do a construction systematically and the communication between members of the task force team was done through the CoP(community of Practice) notice board provided by the Institute. The installation works were done successfully overcoming the difficulties such as on the limited space, on the radiation hazard inside the reactor pool, and finally on the shortening of the shut down period of the HANARO. Without a sweet of the workers of the participating company of HEC(Hyundae Engineering Co, Ltd), HDEC(HyunDai Engineering & Construction Co. Ltd), equipment manufacturer, and the task force team, it is not possible to install the FTL facility within the planned shutdown period. The Commissioning of the FTL is on due to check the function and the performance of the equipment and the overall system as well. The FTL shall start operation with high burn up test fuels in early 2008 if the commissioning and licensing progress on schedule.

• Nuclear Engineering and Technology
• /
• 제25권2호
• /
• pp.248-254
• /
• 1993

본 연구에서는 법규에서 규정하고 있는 주변온도 38$^{\circ}C$의 정상수송조건하에서 수송용기의 건식수송조건에 대한 열해석을 평가하였다. 수송용기는 1회에 PWR 핵연료집합체 4개를 운반할 수 있는 용량을 가지며, 설계기준 핵연료는 연소도 38,000 MWD/MTU, 냉각기간 3년을 기준으로 하였다. 건식수송조건에 대한 열해석을 평가하기 위하여 COBRA-SFS 전산코드를 이용하였다. 수송용기 내부 cavity에 공기, 질소 및 헬륨가스를 채우는 세가지 조건에 대한 해석을 수행하였으며, 최대 핵연료봉의 온도는 수송용기 내부 cavity가 공기인 경우에는 277$^{\circ}C$, 헬륨인 경우에는 226$^{\circ}C$로 계산되었다. 이 값은 건식수송조건에서 수송용기 내부에 장전된 PWR 핵연료집합체가 열적으로 건전성을 유지하기 위한 규정온도보다 낮은 것으로 나타났다.

• 대한기계학회논문집A
• /
• 제40권5호
• /
• pp.437-447
• /
• 2016

원자력 발전소의 반응로에 핵연료 봉으로 이루어진 집합체가 있으며 핵 연료의 연소를 통한 열을 이용하여 발전을 한다. 핵연료 봉은 핵연료와 그를 감싸는 피복관으로 이루어졌으며 연소되는 동안 서로의 상호작용에 대한 해석은 안전성을 평가함에 있어 중요한 사실이다. 본 논문에서는 핵연료와 피복관의 연소 상태에서 기계적 상호작용에 대한 해석 방법에 대하여 제시한다. 온도 해석에 있어서 핵연료와 간극 사이에서의 열전도도가 중요하며 간극 거리와 접촉여부에 따른 접촉 압력이 또한 중요 요소이다. 이에 간극 열전도도는 비결정론적이기 때문에 이를 해결할 수 있는 방법에 대하여 제시했다. 핵 연료의 열팽창에 따른 피복관과의 접촉을 해결하기 위한 계산을 수행하였고 그에 따라 접촉 시 발생하는 응력이 항복함수를 넘어 소성 변형이 일어날 경우 또한 고려하였다. 핵연료의 열팽창에 따라 피복관과 접촉에 의한 소성 변형을 해석하므로 핵연료 봉의 안정성을 평가할 수 있다. 이를 적용하기 위해 3차원 유한요소 모듈을 FORTRAN90을 이용하여 개발하였다. 핵연료와 피복관의 접촉에 의한 탄소성 변형을 주로 다루며 두꺼운 실린더를 통한 간단한 이론 모델을 제시하여 코드에 대해 검증을 실시하였다.

• Nuclear Engineering and Technology
• /
• 제30권4호
• /
• pp.342-352
• /
• 1998

A nuclear design feasibility of soluble boron free(SBF core for the medium-sized(600MWe) PWR was investigated. The result conformed that soluble boron free operation could be performed by using current PWR proven technologies. Westinghouse advanced reactor, AP-600 was chosen as a design prototype. Design modification was applied for the assembly design with burnable poison and control rod absorber material. In order to control excess reactivity, large amount of gadolinia integral burnable poison rods were used and B4C was used as a control rod absorber material. For control of bottom shift axial power shape due to high temperature feedback in SBF core, axial zoning of burnable poison was applied to the fuel assemblies design. The combination of enrichment and rod number zoning for burnable poison could make an excess reactivity swing flat within around 1% and these also led effective control on axial power offset and peak pin power, The safety assessment of the designed core was peformed by the calculation of MTC, FTC and shutdown margin. MTC in designed SBF core was greater around 6 times than one of Ulchin unit 3&4. Utilization of enriched BIO(up to 50w1o) in B4C shutdown control rods provided enough shutdown margin as well as subcriticality at cold refueling condition.

• Nuclear Engineering and Technology
• /
• 제53권11호
• /
• pp.3543-3562
• /
• 2021

The methods and performance of a 3D pin-by-pin neutronics code based on the 2D/1D decoupling method are presented. The code was newly developed as an effort to achieve enhanced accuracy and high calculation performance that are sufficient for the use in practical nuclear design analyses. From the 3D diffusion-based finite difference method (FDM) formulation, decoupled planar formulations are established by treating pre-determined axial leakage as a source term. The decoupled axial problems are formulated with the radial leakage source term. To accelerate the pin-by-pin calculation, the two-level coarse mesh finite difference (CMFD) formulation, which consists of the multigroup node-wise CMFD and the two-group assembly-wise CMFD is implemented. To enhance the accuracy, both the discontinuity factor method and the super-homogenization (SPH) factor method are examined for pin-wise cross-section homogenization. The parallelization is achieved with the OpenMP package. The accuracy and performance of the pin-by-pin calculations are assessed with the VERA and APR1400 benchmark problems. It is demonstrated that pin-by-pin 2D/1D alternating calculations within the two-level 3D CMFD framework yield accurate solutions in about 30 s for the typical commercial core problems, on a parallel platform employing 32 threads.

• 방사성폐기물학회지
• /
• 제18권spc호
• /
• pp.63-74
• /
• 2020

The operational safety assessment is an important part of a safety case for the deep geological repository of spent fuels. It consists of different stages such as the identification of initiating events, event tree analysis, fault tree analysis, and evaluation of exposure doses to the public and radiation workers. This study develops a probabilistic safety assessment method for the operational safety assessment and establishes an assessment framework. For the event and fault tree analyses, we propose the advanced information management system for probabilistic safety assessment (AIMS-PSA Manager). In addition, we propose the Radiological Safety Analysis Computer (RSAC) program to evaluate exposure doses to the public and radiation workers. Furthermore, we check the applicability of the assessment framework with respect to drop accidents of a spent fuel assembly arising out of crane failure, at the surface facility of the KRS⁺ (KAERI Reference disposal System for SNFs). The methods and tools established through this study can be used for the development of a safety case for the KRS⁺ system as well as for the design modification and the operational safety assessment of the KRS⁺ system.

• Nuclear Engineering and Technology
• /
• 제54권10호
• /
• pp.3745-3765
• /
• 2022

The concrete structures related to nuclear safety are threatened by accidental impact loadings, mainly including the low-velocity drop-weight impact (e.g., spent fuel cask and assembly, etc. with the velocity less than 20 m/s) and high-speed projectile impact (e.g., steel pipe, valve, turbine bucket, etc. with the velocity higher than 20 m/s), while the existing studies are still limited in the impact resistant design of nuclear power plant (NPP), especially the primary RC slab. This paper aims to propose the numerical simulation and theoretical approaches to assist the impact-resistant design of RC slab in NPP. Firstly, the continuous surface cap (CSC) model parameters for concrete with the compressive strength of 20-70 MPa are fully calibrated and verified, and the refined numerical simulation approach is proposed. Secondly, the two-degree freedom (TDOF) model with considering the mutual effect of flexural and shear resistance of RC slab are developed. Furthermore, based on the low-velocity drop hammer tests and high-speed soft/hard projectile impact tests on RC slabs, the adopted numerical simulation and TDOF model approaches are fully validated by the flexural and punching shear damage, deflection, and impact force time-histories of RC slabs. Finally, as for the two low-velocity impact scenarios, the design procedure of RC slab based on TDOF model is validated and recommended. Meanwhile, as for the four actual high-speed impact scenarios, the impact-resistant design specification in Chinese code NB/T 20012-2019 is evaluated, the over conservation of which is found, and the proposed numerical approach is recommended. The present work could beneficially guide the impact-resistant design and safety assessment of NPPs against the accidental impact loadings.