• 한국전산유체공학회지
• /
• 제18권3호
• /
• pp.26-33
• /
• 2013

In the present study, unsteady flow simulations of a variable geometry nozzle were conducted using a two-dimensional flow solver based on hybrid unstructured meshes. The variable geometry nozzle is used to achieve efficient performances of aircraft engines at various operating conditions. To describe the motion of the variable geometry nozzle, an algebraic method based on the basis decomposition of normal edge vector was used for the deformation of viscous elements. A ball-vertex spring analogy was used for inviscid elements. The aerodynamic data were obtained for a range of nozzle pressure ratios, and the validations were made by comparing the present results with available experimental data. The unsteady nozzle flows were simulated with an oscillating diverging section and a converging-diverging section. It was found that the nozzle performances are influenced by the nozzle exit flow characteristics, mass flow rate, as well as unsteady effects. These unsteady effects are shown to behave differently depending on the frequency of the nozzle motion.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.238-239
• /
• 2006

Nozzle geometry influences gas dynamics making sprayed particle behavior one of the most important parameters in cold spray process. Gas flows at the entrance convergent section of the nozzle takes place at relatively high temperature and are subsonic. Thus, this region is a very suitable environment for heating spray particle. In this study, numerical simulation and experiments were conducted to investigate the effect of nozzle contour, entrance geometry of nozzle and powder injection position at nozzle on the cold spray process. The process changes were observed through numerical simulation studies and the results were used to find a correlation with coating properties.

• Journal of Mechanical Science and Technology
• /
• 제17권4호
• /
• pp.617-625
• /
• 2003

Effects of Injector nozzle geometry and operating pressure conditions such as opening pressure, ambient pressure. and injection pressure on the transient fuel spray behavior have been examined by experiments. In order to clarify the effect of internal flow inside nozzle on the external spray, flow details Inside model nozzle and real nozzle were alto investigated both experimentally and numerically. for the effect of injection pressures, droplet sizes and velocities were obtained at maximum line pressure of 21 MPa and 105 MPa. Droplet sizes produced from the round inlet nozzle were larger than those from the sharp inlet nozzle and the spray angle of the round inlet nozzle was narrower than that from the sharp inlet nozzle. With the increase of opening pressure, spray tip penetration and spray angle were increased at both lower ambient pressure and higher ambient pressure. The velocity and size profiles maintained similarity despite of the substantial change in injection pressure, however, the increased injection pressure produced a higher percentage of droplet that are likely to breakup.

• 한국자동차공학회논문집
• /
• 제7권6호
• /
• pp.17-31
• /
• 1999

This paper is a review of the results of examining the flow characteristics of gas and particles with regards to pipe-type nozzle and converging nozzles depending on nozzle geometry. The nozzles used in this experiment are the pipe-type nozzle which can sufficiently mix the gas and particles, and the converging nozzle which can rapidly accelerate fluid . The particles used at the time of this experiment each measured 0.8, 30, 60 and 80${\mu}{\textrm}{m}$ in the diameter. The Phase Doppler Particle Analyzer was used to measure the velocity of each particle, and the Hot-wire probe was used to measure the spectrum in order to analyze the flow near the nozzle exit of the 0.8${\mu}{\textrm}{m}$ particle.

• 한국분무공학회지
• /
• 제1권1호
• /
• pp.76-84
• /
• 1996

The nozzle geometry and up-stream inject ion condition affect the characteristics of flow inside the nozzle. such as turbulence and cavitation bubbles. Flow details in fuel nozzle orifice with sudden contraction of cross sectional area have been investigated both experimentally and numerically. The measurements of velocities of internal flow in a scaled-up nozzle with different length to diameter rat io(L/d) were made by laser Doppler velocimetry in order to clarify the effect of internal flow on the characteristics of fuel spray. Mean and fluctuating velocities and discharge coefficients were obtained at various Reynolds numbers. The turbulent intensity and turbulence kinetic energy in a sharp inlet nozzle were higher than that in a round inlet nozzle. Calculations were also performed for the same nozzles as scaled-up experimental nozzles using the SIMPLE algorithm. External spray behavior under different nozzle geometry and up-stream flow conditions using Doppler technique and visualization technique were also observed.

• 한국분무공학회지
• /
• 제10권1호
• /
• pp.24-34
• /
• 2005

Injection technology is one of the important technologies in a diesel engine. Many studies have done on the injection system. In this study, the fuel chamber geometry, the orifice ratio and the needle lift of the injection valve for a marine diesel engine are varied, and simulated. The result shows that the nozzle hole size has influence on the rail pressure and injection duration sensitively. The decrease of the static pressure at the nozzle hole entrance and the increase of the dynamic pressure on the outlet surface are occurred with the increase of the nozzle hole diameter. The highest dynamic pressure of the outlet was occurred at the needle lift of 0.4mm and the nozzle hole diameter of 0.328mm in this test nozzle.

• Journal of Advanced Marine Engineering and Technology
• /
• 제36권8호
• /
• pp.997-1002
• /
• 2012

박용기관에서의 배기규제는 단계별로 강화되고 있으며 연소실 내외의 종합대책이 요구되고 있다. 기관 내부의 연소 특성은 배기배출 특성과 밀접한 관계가 있으며 분사밸브의 노즐과 노즐 홀 특성은 연소에 중요한 영향을 미친다. 분무 특성을 향상시키기 위한 노즐에 관한 연구는 입구형상, 직경 등에 집중되고 있으며, 노즐 출구의 형상에 대해서는 연구가 부족하다. 본 연구에서는 노즐 출구의 형상을 0도에서 90도까지 변화시키면서 계산을 수행하였다. 분사 압력, 질량유량, 유속, 유동특성 등을 종합하였을 때 노즐 출구 각도를 30도와 60도 사이로 하였을 때가 가장 효과적일 것이라 사료된다.

• 한국분무공학회지
• /
• 제12권3호
• /
• pp.154-159
• /
• 2007

Spray tip penetration and spray angle for one main injection were measured at the atmospheric condition with the fuel injection pressure of 270 bar and 540 bar. It investigates an effect of different nozzle hole geometry of conventional cylindrical one and those of elliptical ones. Injection period represented by injector pulse drive was fixed at 1ms. From the result of this study, it is shown that spray tip penetration becomes shorter and spray angle becomes wider with the elliptical nozzle hole geometry due to fast break-up of a fuel liquid column.

• 한국추진공학회지
• /
• 제6권2호
• /
• pp.1-7
• /
• 2002

추진기관은 노즐을 통해 추력을 발생하며 축소-확대 형상의 초음속 노즐에서는 노즐의 설계 팽창비가 내부 유동의 전압력과 배압의 압력비보다 매우 클 때 충격파의 발생과 함께 경계층 박리를 유발한다. 노즐 내부에서의 충격파 발생과 유동의 박리는 주어진 유동의 압력비에 가장 적합한 노즐형상을 구현하는 것으로 실제의 구조적 노즐의 형상보다 짧은 노즐에서 나타나는 유동과 같은 현상을 보인다. 수치 해석적 방법으로 고정된 형상의 2차원 노즐 내부의 충격파와 경계층 박리 현상에 관한 연구를 수행하였고 Hunter가 행한 실험적 연구와 비교하였다. 수치해석은 TVD 기법을 이용한 압축성 유체 해석 코드와 SST 2방정식 난류 모델을 이용하여 수행되었다. 낮은 압력비에서의 충격파와 경계층과의 상호작용에 의한 $\lambda$형태의 충격파 시스템을 잘 보여주고 있고 추력 값의 비교를 통해 고정된 형상의 노즐을 이용하여 필요한 운용범위를 충족할 수 있음을 알 수 있었다.

• 대한기계학회논문집B
• /
• 제20권6호
• /
• pp.1971-1982
• /
• 1996

The breakup of liquid jet is the result of competing, unstable hydrodynamic forces acting on the liquid jet as it exit the nozzle. The nozzle geometry and up-stream injection conditions affect the characteristics of flow inside the nozzle, such as turbulence and cavitation bubbles. A set of calculation of the internal flow in a single hole type nozzle were performed using a two dimensional flow simulation under different nozzle geometry and up-stream flow conditions. The calculation showed that the turbulent intensity and discharge coefficient are related to needle position. The diesel nozzle with sharp inlet under actual engine condition has possibility of cavitation, but round inlet nozzle has no possibility of cavitation.