• Structural Engineering and Mechanics
• /
• v.50 no.6
• /
• pp.723-740
• /
• 2014

A fracture criterion based on the strain energy density (SED) over a control volume, which embraces the notch edge, is employed in the present paper to assess the fracture loads of some U-notched Brazilian disk (UNBD) specimens. The specimens are made of commercial graphite and have been tested under pure mode I, pure mode II and mixed mode I/II loading. The results show that the SED criterion allows to successfully assess the fracture loads of graphite specimens for different notch tip radii and various mode mixity conditions with discrepancies that fall inside the scatter band of ${\pm}20%$.

• International Journal of Internet, Broadcasting and Communication
• /
• v.12 no.2
• /
• pp.83-89
• /
• 2020

A microstrip feedline based open ended folded-slot antenna is proposed for ultra-wideband (UWB) applications. The prototype of the proposed antenna is fabricated on the FR4 dielectric substrate. The proposed antenna has a wide n-shaped slot that is useful for designing circuit components on the same printed circuit board (PCB) as that of the radio frequency (RF) modules. The proposed antenna use two kinds of slots as radiators, and each slots have different characteristics because of the different type of ends of the slot. The wideband characteristic can be obtained by resonances of each slot which are occurred at different frequencies. The measured impedance bandwidth (S₁₁≤ -10 dB) is 2.9-11.56 GHz, and the antenna peak gain is 2-4 dBi over the UWB range. The antenna has a stable omni-directional radiation pattern and only a small group-delay variation across the UWB passband. In addition, we present a modified design with band-notched characteristics of a 5 GHz wireless local area network (WLAN) frequency band.

• Journal of electromagnetic engineering and science
• /
• v.18 no.2
• /
• pp.73-77
• /
• 2018

This paper proposes a dual-band bandpass filter using stepped-impedance resonators (SIRs) with parallel coupled structures. The proposed filter adopts U-shaped SIRs with parallel coupled lines (PCLs) that have interdigital and comb-line shorted ends. The central PCLs build an upper passband and a transmission zero, and the two U-shaped SIRs build a lower passband. Four resonators and coupling structures are theoretically analyzed to derive its scattering parameters. A novel dual-band bandpass filter is designed and fabricated using the induced scattering characteristics. The measured results show that the fabricated dual-band bandpass filter has an insertion loss of less than 1.02 dB in the lower band of 2.45 GHz and of 3.01 dB in the upper band of 3.42 GHz, and a band-to-band isolation of more than 40 dB, from 3.14 to 3.2 GHz.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.7
• /
• pp.3431-3436
• /
• 2013

Band-notched ultra-wideband (UWB) antennas using frequency selective surfaces (FSSs) are presented. The proposed antennas utilized the band rejection characteristic of typical FSS unit cells. We loaded the FSS unit cells on the same plane of planar UWB antenna. These antennas are designed to reject the interference from the wireless local area network band, 5.15-5.825 GHz in the UWB band, 3.1-10.6 GHz. The measured peak gains of the proposed antennas are more than 2 dBi at both operation edge and center frequencies, and sufficient to apply for commercial purpose. The antennas are small size and planar shape for the purpose of the small mobile application, and enhanced design freedom by using various existing FSS unit cells.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.3
• /
• pp.275-281
• /
• 2011

In this paper, we proposed the small planar monopole antenna with modified ground plane for UWB communications. The proposed antenna not only shows Ultra-Wideband characteristic(3.1~10.6 GHz) suitable for UWB communications but has partially notched-band characteristic to reject 5 GHz WLAN band(5.15~5.35 GHz, 5.470~5.825 GHz). The proposed antenna improved impedance matching through two slits on ground plane, and the rejection band was induced by two ${\lambda}$/4 open stubs on center of two slits. Fabricated antenna satisfied VSWR${\leq}$2 in 2.88~10.83 GHz except for the band rejection of 5.08~5.83 GHz.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.47 no.5
• /
• pp.69-74
• /
• 2010

In this paper, we proposed a compact arbitrary dual-band band-stop filter using CRLH transmission line. The proposed filter used CRLH transmission line as stub and it developed dual-band band-stop characteristics using non-linear phase response of CRLH transmission line. The size of proposed filter is compact. And it can control arbitrary dual stop band. In this paper, designed band-stop filter at GPS band and ISM band As result, the S(2,1) is about -30dB at GPS band and about -29dB at ISM band. The fabricated filter is very compact. Its dimension is 10mm*15mm.

• Journal of Advanced Navigation Technology
• /
• v.13 no.5
• /
• pp.714-719
• /
• 2009

In this paper, a compact antenna with band-rejected characteristic for Ultra-Wideband(UWB) applications is proposed. The designed antenna not only shows sufficient impedance bandwidth but has band-rejected characteristic for the frequency band of 5.15~5.825GHz limited by IEEE 802.11a and HIPERLAN/2. To obtain both properties of wideband band rejection, the techniques of a partial ground plane and embedded thin U-slot into planar radiator are used respectively. A designed antenna satisfied a VSWR less than 2:1 for the frequency band of 3.1~10.3GHz with band rejection of 4.90~5.92GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.8
• /
• pp.781-787
• /
• 2004

In this paper, a novel dual and wide band aperture stacked patch antenna for Cellular/PCS/IMT-2000 base station is presented. It consists of single microstrip patch having notches along the radiating patch, two dielectric substrates and a form material. To achieve wide band characteristic, we utilize the coupling effect between the notched patch and the resonant aperture in the ground plane and by properly cutting notches on the patch, an aperture stacked patch antenna could be designed to yield dual frequency operation. By the proper choice of resonant aperture size and height of a foam material, dual and wide band characteristic could be realized the measured impedance bandwidth(1:1.5 VSWR) of designed antenna at lower band(860 MHz) reaches 77 MHz and covers the Cellular CDMA band(824∼894 MHz). The measured impedance bandwidth(1:1.5 VSMR) of the designed antenna at upper band(1,960 MHz) is about 550 MHz and covers both the PCS band(1,750∼l,870 MHz) and the for-2000 band(1,920∼2,170 MHz). Good broadside radiation with high gain(5.65∼7.4 dBi) characteristics have also been observed.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.25 no.4
• /
• pp.274-286
• /
• 2005

Fracture behaviors and acoustic emission (AE) characteristics of single-edge-notched monolithic aluminum plates and glass fiber/aluminum hybrid laminate plates have been investigated under tensile loads. AE signals from monolithic aluminum could be classified into two different types: signals with low frequency band and high frequency band. High frequency signals were detected in the post stage of loading beyond displacement of 0.45mm. For glass fiber/aluminum laminates, AE signals with high amplitude and long duration were additionally confirmed on FFT frequency analysis, which corresponded to macro-crack propagation and/or delamination between A1 and fiber layers. On the basis of the above AE analysis and fracture observation with optical microscopy and ultrasonic T scan, characteristic features of AE associated with fracture processes of single-edge-notched glass fiber/aluminum laminates were elucidated according to different fiber ply orientations.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.12 no.6
• /
• pp.2734-2747
• /
• 2018

In this study, a novel fractal ring antenna with a compact size of $24{\times}9{\times}0.8mm^3$ was configured using three iterations. Low profile, circular polarization, and measured operating bands (4.5-6.5 GHz) meet specifications of the upper band used in Wi-Fi and WiMAX applications. The antenna featured, stable radiation properties, especially gain and efficiency, in the notched band (92%). In deep, the antenna impedance, reflection coefficients, surface current distribution and circular polarization for the three iterations had been studied to improve the process of antenna design and its radiation characteristics.