• Advances in concrete construction
• /
• 제14권5호
• /
• pp.317-330
• /
• 2022

This paper investigated computationally and experimentally the interaction here between a notch as well as a micropore under uniaxial compression. Brazilian tensile strength, uniaxial tensile strength, as well as biaxial tensile strength are used to calibrate PFC2d at first. Then, uniaxial compression test was conducted which they included internal notch and micro pore. Experimental and numerical building of 9 models including notch and micro pore were conducted. Model dimensions of models are 10 cm × 10 cm × 5 cm. Joint length was 2 cm. Joints angles were 30°, 45° and 60°. The position of micro pore for all joint angles was 2cm upper than top of the joint, 2 cm upper than middle of joint and 2 cm upper than the joint lower tip, discreetly. The numerical model's dimensions were 5.4 cm × 10.8 cm. The fractures were 2 cm in length and had angularities of 30, 45, and 60 degrees. The pore had a diameter of 1 cm and was located at the top of the notch, 2 cm above the top, 2 cm above the middle, and 2 cm above the bottom tip of the joint. The uniaxial compression strength of the model material was 10 MPa. The local damping ratio was 0.7. At 0.016 mm per second, it loaded. The results show that failure pattern affects uniaxial compressive strength whereas notch orientation and pore condition impact failure pattern. From the notch tips, a two-wing fracture spreads almost parallel to the usual load until it unites with the sample edge. Additionally, two wing fractures start at the hole. Both of these cracks join the sample edge and one of them joins the notch. The number of wing cracks increased as the joint angle rose. There aren't many AE effects in the early phases of loading, but they quickly build up until the applied stress reaches its maximum. Each stress decrease was also followed by several AE effects. By raising the joint angularities from 30° to 60°, uniaxial strength was reduced. The failure strengths in both the numerical simulation and the actual test are quite similar.

• Journal of electromagnetic engineering and science
• /
• 제10권1호
• /
• pp.39-44
• /
• 2010

In this paper, a compact wideband antenna with a band-notch function is proposed. It operates over the UWB band with a band-stop characteristic. To increase the impedance bandwidth, a ring-shaped radiator is used. By attaching a circular stub to the ring-shaped radiator, the band-notch performance is obtained. The proposed antenna operates over a frequency range from 2.7 GHz to 11 GHz to satisfy the 10-dB return-loss requirement and provides band-stop performance in the frequency band from 5.15 GHz to 6.1 GHz. Experimental results reveal that the proposed antenna exhibits good radiation performance and is suitable for UWB applications.

• 비파괴검사학회지
• /
• 제11권1호
• /
• pp.13-22
• /
• 1991

In this paper, 3-dimensional fracture phenomena in the local area near a through notch tip located between the surface and the canter were investigated by using embedded dyeing grids with the pitch of $50.8{\mu}$. It was confirmed that displacement V and square root of distance from notch tip $y^{1/2}$ are not proportional in the local area of $\sqrt{{\mid}y{\mid}}\;<\;0.3mm^{1/2}$ and the maximum shea strain ${\varepsilon}_{xymax}$ near a notch tip occurred at the curvature beginning point of the notch curve. It was also noted that the maximum strain ${\varepsilon}_{xymax}$ in the thickness direction occurred at the interior, where the ratio of the distance measured from surface to the half of thickness of specimen is 0.3.

• Journal of Microbiology and Biotechnology
• /
• 제30권3호
• /
• pp.448-458
• /
• 2020

We investigated the therapeutic effects of microRNA-139-5p in relation to osteoporosis of bone marrow-derived mesenchymal stem cell (BMSCs) and its underlying mechanisms. In this study we used a dexamethasone-induced in vivo model of osteoporosis and BMSCs were used for the in vitro model. Real-time quantitative polymerase chain reaction (RT-PCR) and gene chip were used to analyze the expression of microRNA-139-5p. In an osteoporosis rat model, the expression of microRNA-139-5p was increased, compared with normal group. Down-regulation of microRNA-139-5p promotes cell proliferation and osteogenic differentiation in BMSCs. Especially, up-regulation of microRNA-139-5p reduced cell proliferation and osteogenic differentiation in BMSCs. Overexpression of miR-139-5p induced Wnt/β-catenin and down-regulated NOTCH1 signaling in BMSCs. Down-regulation of miR-139-5p suppressed Wnt/β-catenin and induced NOTCH1 signaling in BMSCs. The inhibition of NOTCH1 reduced the effects of anti-miR-139-5p on cell proliferation and osteogenic differentiation in BMSCs. Activation of Wnt/β-catenin also inhibited the effects of anti-miR-139-5p on cell proliferation and osteogenic differentiation in BMSCs. Taken together, our results suggested that the inhibition of microRNA-139-5p promotes osteogenic differentiation of BMSCs via targeting Wnt/β-catenin signaling pathway by NOTCH1.

• 한국통신학회논문지
• /
• 제42권1호
• /
• pp.286-290
• /
• 2017

본 논문에서는 노치 대역 특성을 갖는 UWB 육각형 패치 안테나를 제안하였다. 노치 대역은 WLAN의 5.15 ~ 5.85 GHz 대역이며, 원형 슬릿을 패치에 삽입하여 유도하였다. 제안된 안테나의 임피던스 대역폭은 3.1 ~ 11.85 GHz 대역으로 UWB 통신 시스템의 대역폭을 만족하였으며, 5.2 ~ 5.8 GHz 대역에서 노치 대역 특성을 보였다. 안테나의 방사패턴은 XZ-plane에서 $0^{\circ}$와 $180^{\circ}$에서 지향성의 패턴을 보이며, YX-plane에서 무지향성 패턴을 보인다. 또한, 주파수가 증가할수록 안테나 이득도 증가하며, 노치 대역 구간에서는 안테나 이득이 감소하였다. 제안된 안테나는 두께 1.62 mm, 손실 탄젠트 0.0035, 유전율 4.5를 갖는 TRF-45 기판에 설계되었으며, 설계는 Ansys사의 HFSS를 사용하였다.

• Journal of Welding and Joining
• /
• 제2권1호
• /
• pp.41-48
• /
• 1984

Recrystallization technique was applied to analyze plastic strain at the notch tip of coarse grain HAZ in mild steel (SB 41) and high strength steel (SA 588). The notch tip of specimen was deformed by three point bending. Accumulated displacement (Crack Opening Displacement ${delta}t$) by the monotonic and cyclic loading under room temperature and hot strain embrittlement temperature ($250^{\circ}C$) was 0~1.0mm. Recrystallization heat treatment conditions were $650^{circ}C{ imes}3hr$ for SB 41 and $700^{circ}C{ imes}3hr$ for SA 588. The experimental results obtained were as follows ; 1) Distribution of the effective plastic strain at plastic zone was appeared by the function of crack opening displacement, and plastic zone or the effective plastic strain increased with crack opening displacement. 2) Plastic strain at notch tip of HAZ due to accumulated hot strain calculated as follows. .epsilon. over bar $_{p}$ = .epsilon. over bar $_{cr}$ (x/ $R_{x}$ ) $^{m}$ (m=0.25) 3) Work hardending ratio of notch tip for hot strain was linearly increased with .epsilon. over bar $_{max}$ and dependent upon the material types.s.

• KCI Concrete Journal
• /
• 제14권1호
• /
• pp.43-50
• /
• 2002

In this study, size effect tests were conducted on axial compressive strength of concrete members. An experiment of Mode I failure, which is one of two representative compressive failure modes, was carried out by using dimensionally proportional cylindrical specimens (CS). An adequate notch length was taken from the experimental results obtained from the compressive strength experiment of various initial notch lengths. Utilizing the notch length, specimen sizes were then varied. In addition, new parameters for the modified size effect law (MSEL) were suggested using Levenberg-Marquardt's least square method (LSM). The test results show that size effect was apparent for axial compressive strength of cracked specimens. Namely, the effect of initial notch length on axial compressive strength size effect was apparent.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제54권10호
• /
• pp.477-482
• /
• 2005

In this paper, detent force is minimized using notch and slot-aputure width adjustment in a slotted PMLSM. This time, the moving model node technique has used to reduce the time and the effort for calculation according to changing design parameters. As the result, the detent force of proposed model is decreased from 9.44[N] to 0.97[N] compare with it of basic model greatly. The thrust Is decreased 1.3[$\%$] from 342.07[N] to 337.48[N] a little. The notch is applied to PMLSM simply, the detent force is reduced greatly.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.132-133
• /
• 2006

Optimized choice of material for two principally different types of PM components is presented. The first is characterized by high stresses in areas with high stress concentrations (for example synchronizer hubs with very sharp notches, typically <0.25mm in the pre-synchronizer slot and the inner splines). The second type has slightly larger notch radii (small spur gears and sprockets with typically notch radii between 1- 3mm). Diffusion alloyed materials are well suited for sharp notch components. Pre-alloyed materials are also well suited for applications with sharp notches if compressive residual stresses in the notch roots are created by appropriate process control. A free choice of material is available for components with the larger notch radii.

• 한국인터넷방송통신학회논문지
• /
• 제13권1호
• /
• pp.221-227
• /
• 2013

최근 인터넷이 주 정보원으로 작용하고 인터넷의 보급이 확산되는 정보화시대에 인터넷 망이 닿지 않는 지역의 Last Mile Solution에 적합한 대안으로서 전력선 통신에 관한 연구가 진행되고 있다. 하지만, 전력선 통신은 전력을 전송하도록 설계되었기 때문에 높은 고주파 신호를 보내게 되면 부근의 무선통신 서비스에 영향을 주게 된다. 이러한 간섭을 제거하기 위해서 일반적인 방법으로는 Notch filter를 주로 사용한다. 본 논문에서는 WDF 방식을 적용한 동적 고성능 Notch filter를 MATLAB을 통해 성능을 확인하였고 TI사의 TMS320C6416T DSP 보드를 이용하여 구현하였다.