• Journal of Welding and Joining
• /
• 제27권6호
• /
• pp.31-35
• /
• 2009

When conducting CTOD test, especially in thick welded steel plate, fatigue pre-cracking occasionally failed to satisfy the requirements of standards thus making the test result invalid. Internally accumulated residual stress of test piece has been thought as one of the main reasons. The propagation of fatigue crack, started from the tip of machined notch, which might have propagated irregularly due to residual stress field. To overcome this kind of difficulty three methods to modify the residual stress are suggested in standard i.e. local compression, reverse bending and stepwise high-R ratio method. In this paper not only multi pass welding but also local pre-compressing process of thick steel plate has been simulated using finite element method for clarifying variation of internal welding residual stress. The simulated results show that welding residual stress is compressive in the middle section of the model and it is predominantly increased after machining the specimen. Comparing as-welded state all component of the welding residual stress changing to compressive in the tip of machine notch whereas residual stress of the outer area remain as tensile condition relatively. Analysis results also show that this irregular residual stress distribution is improved to be more uniformly by applying local compression.

• Coupled systems mechanics
• /
• 제11권3호
• /
• pp.217-231
• /
• 2022

The present paper is concerned with a delamination analysis of a multilayered frame structure that exhibits non-linear creep behavior. A solution to the strain energy release rate is obtained by considering the time-dependent complementary strain energy in the frame. The mechanical behavior of the frame is treated by using a non-linear stress-strain-time relationship. The time-dependent solution to the strain energy release rate obtained in the present paper holds for a multilayered frame made of arbitrary number of adhesively bonded layers of different thicknesses and material properties. Besides, the dealamination is located arbitrary along the thickness. The solution to the strain energy release rate is verifiedby applying the J-integral approach. A parametric study of the strain energy release rate is carried-out. Two three-layered frame configurations are analyzed in order to evaluate the influence of the delamination crack location along the thickness on the strain energy release rate. The strain energy release is analyzed also for the case when a notch is cut-out in the inner delamination crack arm. The results obtained are compared with these for a frame without a notch.

• 한국가스학회지
• /
• 제12권1호
• /
• pp.1-6
• /
• 2008

샤피충격시험은 동적하중 하에 있는 고분자 재료의 거동을 이해하는데 가장 널리 사용되고 있는 방법이다. 본 연구에서는 샤피충격시험장치에서 얻어지는 파단에너지를 사용하여 나일론 소재 샤피 시편의 노치각도에 따른 에너지 해방율을 구하는 방법을 제시하였다. 또한 샤피충격시험장치를 계장화하여 최대 하중과 파단 시까지 소요되는 에너지 등의 파손인자들을 산출하였다. 그리고 노치각도에 따른 동적파괴 인성치와 유한요소법을 사용하여 중앙집중 하중 하에서 사피 시편의 노치각도에 따른 응력분포를 산출하였다.

• Nuclear Engineering and Technology
• /
• 제52권7호
• /
• pp.1579-1586
• /
• 2020

Dissimilar metal joints (DMJs) are more common in the application of piping system of many industries. A 2- D and 3-D finite element analysis (FEA) is carried out on dissimilar metal Single Edged Notch Bending (DMSENB) specimens fabricated from ferritic steel, austenitic steel and Inconel - 182 alloy to study the behavior of DMJs with constraints by using linear elastic fracture mechanics (LEFM) principles. Studies on DMSENB specimens are conducted with respect to (i) dissimilar metal joint width (DMJW) (geometrical constraints) (5 mm, 10 mm, 20 mm, 30 mm and 50 mm) (ii) strength mismatch (material constraints) and (iii) crack lengths (16 mm, 20 mm and 24 mm) to study the DMJ behavior. From the FEA investigation, it is observed that (i) SIF increases with increase of crack length and DMJWs (ii) significant constraint effect (geometry, crack tip and strength mismatch) is observed for DMJWs of 5 mm and 10 mm (iii) stress distribution at the interfaces of DMSENB specimen exhibits clear indication of strength mismatch (iv) 3-D FEA yields realistic behavior (v) constraint effect is found to be significant if DMJW is less than 20 mm and the ratio of specimen length to the DMJW is greater than 7.4.

• Composites Research
• /
• 제26권2호
• /
• pp.79-84
• /
• 2013

본 연구에서는 적층판 시편의 피로손상 균열진전 시험결과와 적층보강판 구조의 응력강도 해석결과를 기초로 충격손상을 모사한 원공과 노치손상을 내재한 보강재 본딩접합 적층보강판 구조의 피로손상 균열진전 수명예측에 대하여 고찰하였다. 그리고 적층보강판 구조시편에 대한 손상허용 시험결과와 손상진전 수명예측 해석결과를 비교분석한 결과 손상균열 길이 변화에 따라 최종파단에 대한 잔여강도를 예측하고 손상허용성 평가를 할 수 있었다.

• Structural Engineering and Mechanics
• /
• 제44권6호
• /
• pp.705-733
• /
• 2012

In this work, an experimental examination was carried out to study interfacial stresses developed at the junction zones between carbon fiber reinforced plastic (CFRP) fabrics (~1 mm thickness) and tensile concrete portion in CFRP retrofitted RC beams. In this respect, initially six similar RC beams of $150{\times}150{\times}1000mm$ dimensions were prepared. Three of which were strengthened with CFRP fabrics at the tensile side of the beams. Furthermore, a notch was cut at the center of the bottom surface for all of the studied beams. The notch was 15 mm deep and ran across the full width of tension side of the beams. The mentioned interfacial stresses could be calculated from strains measured using strain gauges mounted on the interface zone of the tensile concrete and the CFRP sheet. Based on the results obtained, it is shown that interfacial stresses developed between CFRP fabrics and RC beam had a noticeable effect on debonding failure mode of the latter. The load carrying capacity of CFRP strengthened RC specimens increased ~75% compared to that of the control RC beams. This was attributed to the enhancement of flexural mode of the former. Finally, finite element analysis was also utilized to verify the measured experimental results.

• 터널과지하공간
• /
• 제20권1호
• /
• pp.65-72
• /
• 2010

암반발파에서 평활한 파단면을 확보하고 굴착손상영역을 제어하기 위하여 노치장약공을 이용한 균열제어공법이 제안되었다. 본 연구에서는 노치형상과 장약조건이 균열발생 및 성장에 미치는 영향을 살펴보기 위하여 날개형 노치장약공을 갖는 발파모델을 구축하고 동적 파괴과정 해석법을 이용한 암반 파괴과정 해석을 수행하였다. 그 결과, 노치 길이가 증가함에 균열의 성장 길이가 증가하며 파단면의 거칠기가 감소하고 장약공 상하부에 손상균열의 발생이 억제되는 경향을 보였다. 해석결과로부터 노치 길이 및 개구 폭에 따른 응력집중계수의 변화 및 균열발생 양상을 비교 분석하여 균열제어에 미치는 영향인자에 대하여 고찰하였다.

• Journal of Welding and Joining
• /
• 제22권2호
• /
• pp.28-32
• /
• 2004

Fatigue life at seam weldment of thick plate was estimated using the finite element and FEM-FAT(an exclusive fatigue solver). Finite element meshing at toe and root of weldment was based oil Radaj's theory. Also, the results of FE analysis were compared with experimental results in the point of Miner's Rule. The results of FE and FEM-FAT analysis were in accord with experimental results within 60% confidence. This result reveals that above techniques is useful in assessment of seam weldment and to be an alternative method instead of an object experiment.

• Journal of Mechanical Science and Technology
• /
• 제15권12호
• /
• pp.1616-1622
• /
• 2001

Fiber composite materials are widely used in aerospace industries due to their high specific strength and stiffness. Especially, the increasing use of polymer composite materials for injection of automobile components has led to a considerable interest in the application of stress pattern analysis by thermal emission to these composite materials. Therefore, in this study the microstructure of glass fiber orientation at the parent and weld line of polycarbonate is observed by a light transmission. And we also investigate a stress concentration model of a notch including short glass fibers. Especially the polymer injection weld reorients the fiber to suggest a new method for the evaluation of inhomogeneous deformation.

• 대한치과의사협회지
• /
• 제48권4호
• /
• pp.297-307
• /
• 2010

Noncarious cervical lesions(NCCLs) are characterized as structural defects found on the tooth surface of the cement-enamel junction. Loss of tooth structure through noncarious mechanisms may vary in etiology and clinical presentation for each individual but presently many clinician now classify this as tooth failure of abfraction due to the stress applied in the cervical area of the tooth under oral physiological and pathological loads. In the current study, we investigated the stress distribution of maxillary premolar with NCCL using simulated 3D finite element analysis. The results were as follows: 1. In the sound maxillary premolar, the stresses were highly concentrated at cervical enamel surface of the mesiobuccal line angle, asymmetrically. 2. Once the lesion has been formed, the highest stress concentration was observed around the apex of the wedge shaped lesion. 3. In four types of NCCL, the patterns of stress distribution were similar and the peak stress was observed at mesial corner and also stresses concentrated at lesion apex. 4. Lesion cavity modification of rounding apex, reduced stress of lesion apex. 5. When restoring the notch-shaped lesion, material with high elastic modulus worked well at the lesion apex and material with low elastic modulus worked well at the cervical cavosurface margin.