• Steel and Composite Structures
• /
• 제36권1호
• /
• pp.75-86
• /
• 2020

The grid structures with welded hollow spherical joint (WHSJ) have gained increasing popularity for use in industrial buildings with suspended cranes, and usually welded with steel tube (ST). The fatigue performance of steel tube-welded hollow spherical joint (ST-WHSJ) is however not yet well characterized, and there is little research on fatigue life prediction methods of ST-WHSJ. In this study, based on previous fatigue tests, three series of specimen fatigue data with different design parameters and stress ratios were compared, and two fatigue failure modes were revealed: failure at the weld toe of the ST and the WHSJ respectively. Then, S-N curves of nominal stress were uniformed. Furthermore, a finite element model (FEM) was validated by static test, and was introduced to assess fatigue behavior with the hot spot stress method (HSSM) and the effective notch stress method (ENSM). Both methods could provide conservative predictions, and these two methods had similar results. However, ENSM, especially when using von Mises stress, had a better fit for the series with a non- positive stress ratio. After including the welding residual stress and mean stress, analyses with the local stress method (LSM) and the critical distance method (CDM, including point method and line method) were carried out. It could be seen that the point method of CDM led to more accurate predictions than LSM, and was recommended for series with positive stress ratios.

• 한국가스학회지
• /
• 제17권1호
• /
• pp.19-25
• /
• 2013

용접에 의한 가스설비, 교량, 선박 등 강 구조물의 접합 방법은 대부분 십자형이나 T형의 필릿 용접으로 이루어지며 구조물의 형상과 용도에 따라 완전 용입 또는 불완전 용입 상태로 이루어진다. 본 연구에서는 십자형 필릿용접 구조물에 대하여 재료 두께별 용입 깊이에 따른 피로 균열 특성을 파악하였고, 그 결과로부터 무한수명 영역내에서의 안전 설계응력에 대하여 고찰하였다. 미 용입 길이가 길면 루트 부 파괴가 되어 무한 수명 영역은 작고 미 용입 길이가 짧으면 토우부 파괴가 되어 무한 수명 영역은 크게 나타났다. 3층 용접한 재료 두께 20mm의 경우가 2층 용접한 재료 두께 10mm, 15mm의 경우보다 미세한 페라이트 침상 조직을 더 많게 형성시켜 노치 인성을 증가시키므로 서 피로강도와 무한 수명을 더 향상시킨 것으로 나타났다.

• 한국가스학회지
• /
• 제16권4호
• /
• pp.16-22
• /
• 2012

용접기술의 발달과 더불어 기계, 교량, 선박 그리고 가스설비 등의 제작공정을 위하여 용접의 이용이 증가하고 있다. 따라서 그들의 용접 구조물 제작을 위하여 높은 생산성과 안전설계를 고려하는 용접 법을 개발하는 것이 요구되고 있다. 본 연구에서는 재료 두께, 용접층수, 하중 방향 그리고 토우부의 노치 반경과 관련하여 완전 용입 십자형 필릿 용접부의 피로강도 및 피로수명의 특성에 대하여 기초적으로 고찰하였다. 대부분의 피로파괴는 십자형 필릿 용접의 토우부에서 발생하였다. 피로강도 및 피로수명은 토우 부의 노치 반경과 플랭크 각에 의한 응력집중의 영향을 받고 있다. 토우부의 금속이 다층 용접에 의하여 어닐링 되고 확산 되었으며 그 결과 침상 페라이트 조직이 형성되어 피로강도와 피로수명을 향상시켰다.

• 대한물리치료과학회지
• /
• 제6권2호
• /
• pp.1041-1062
• /
• 1999

This study is to stimulate the model of which top notch muscle stimuli physical therapy has been made on the basis of GCM. GCM has been studied on the hypermobility & hypomobility pattern on the part of spine & extremity, and the body characteristics of four body types, which is the tilting of seal scapular & ilium. The purpose of this study is to analysize the type of GCM which has been focused on the spine & extremity for the patients having dysfunctions of neuromuscular system, being analysized the movement. The result of this study is as following; 1) The First hypothesis: The hypermobility & hypomobility pattern assorted by the tilting of scapular & ilium, as does the former study analysize was claimed that it would be in line with the pattern for hypermobility hypomobility and physical characteristics according to each body type at the percentage of at least 60(p<.001). 2) The 2nd hypothesis : Stimuli therapy of muscle dealing with physical characteristics and joint hypermobility hypomobility has the important role in restoring the deformity and keeping anatomical postural plumb alignment also it would a highly effects on correcting the body even though the stimuli area was limited to four areas and it was lack of time compared with those applied by general physical therapy(p<.001). As above the result, the top-notch type for physical therapy based on hypermobility hypomobility pattern by 4 body types which has been studied on tilting of scapular & ilium is more specificed and specialized than those of general physical therapy technologies. So this study will be believed to dedicate to restoration ideal anatomical postural plumb alignment based on spinal Manipulation and the concept of whole person as well as to being simple and effective to apply.

• Structural Engineering and Mechanics
• /
• 제63권3호
• /
• pp.361-370
• /
• 2017

Through the use of finite element analysis and acoustic emission techniques we have evaluated the interfacial failure of a carbon fiber reinforced polymer (CFRP) repair patch on a notched aluminum substrate. The repair of cracks is a very common and widely used practice in the aeronautics field to extend the life of cracked sheet metal panels. The process consists of adhesively bonding a patch that encompasses the notched site to provide additional strength, thereby increasing life and avoiding costly replacements. The mechanical strength of the bonded joint relies mainly on the bonding of the adhesive to the plate and patch stiffness. Stress concentrations at crack tips promote disbonding of the composite patch from the substrate, consequently reducing the bonded area, which makes this a critical aspect of repair effectiveness. In this paper we examine patch disbonding by calculating the influence of notch tip stress on disbond area and verify computational results with acoustic emission (AE) measurements obtained from specimens subjected to uniaxial tension. The FE results showed that disbonding first occurs between the patch and the substrate close to free edge of the patch followed by failure around the tip of the notch, both highest stress regions. Experimental results revealed that cement adhesion at the aluminum interface was the limiting factor in patch performance. The patch did not appear to strengthen the aluminum substrate when measured by stress-strain due to early stage disbonding. Analysis of the AE signals provided insight to the disbond locations and progression at the metal-adhesive interface. Crack growth from the notch in the aluminum was not observed until the stress reached a critical level, an instant before final fracture, which was unaffected by the patch due to early stage disbonding. The FE model was further utilized to study the effects of patch fiber orientation and increased adhesive strength. The model revealed that the effectiveness of patch repairs is strongly dependent upon the combined interactions of adhesive bond strength and fiber orientation.

• 열처리공학회지
• /
• 제23권4호
• /
• pp.183-190
• /
• 2010

There are many methods to reduce the weight and the cost of the automobile body, among them, Tailor Welded Blank (TWB) is new welding method applied to body structure. It is necessary to evaluate mechanical properties of TWB structures or sheets for the application to automobile body parts. In this study, the stiffness of T-type and L-type joint structures, composite of TWB panel, which simplified two portions of side structure in automobile body were investigated. Additionally, the fatigue properties of TWB panels were obtained. Two types of welding technologies, laser and mash seam welding, were used to join mild panels with different thickness. This results are compared with conventional structures. The results are as follows: 1) The stiffness of joint structures, composite of TWB panel, is approximately 17% higher than that of conventional ones. 2) The location of welding line in TWB had a effect on the in plane bending stiffness, but not on the out of plane bending stiffness. 3) In terms of welding technology type, the mash seam welding show higher stiffness than the laser welding for in plane bending stiffness. But minimal differences in both types are revealed for out of plane bending stiffness. 4) The fatigue strength, composite of TWB panel, is lower than that of base steel. It is thought that defects in the welding zone had the action of notch in the fatigue test.

• Nuclear Engineering and Technology
• /
• 제52권12호
• /
• pp.2949-2957
• /
• 2020

Fatigue crack growth model has been developed for dissimilar metal weld joints of a piping component under cyclic loading, where in the crack is located at the center of the weld in the circumferential direction. The fracture parameter, Stress Intensity Factor (SIF) has been computed by using principle of superposition as K_H + K_M. K_H is evaluated by assuming that, the complete specimen is made of the material containing the notch location. In second stage, the stress field ahead of the crack tip, accounting for the strength mismatch, the applied load and geometry has been characterized to evaluate SIF (K_M). For each incremental crack depth, stress field ahead of the crack tip has been quantified by using J-integral (elastic), mismatch ratio, plastic interaction factor and stress parallel to the crack surface. The associated constants for evaluation of K_M have been computed by using the quantified stress field with respect to the distance from the crack tip. Net SIF (K_H + K_M) computed, has been used for the crack growth analysis and remaining life prediction by Paris crack growth model. To validate the model, SIF and remaining life has been predicted for a pipe made up of (i) SA312 Type 304LN austenitic stainless steel and SA508 Gr. 3 Cl. 1. Low alloy carbon steel (ii) welded SA312 Type 304LN austenitic stainless-steel pipe. From the studies, it is observed that the model could predict the remaining life of DMWJ piping components with a maximum difference of 15% compared to experimental observations.

• Journal of Welding and Joining
• /
• 제15권4호
• /
• pp.90-98
• /
• 1997

A copper-tungsten sintered alloy(Cu-W) has been friction welded to a tough pitch copper in order to investigate the effect of friction pressure on bonding strength and a charicteristic of fracture. The tensile strength of the friction welded joint was increased up to 90% of the Cu base metal under the condition of friction time 1.2 sec, friction pressure 4.5kgf/$\textrm{mm}^2$ and upset pressure 10kgf/$\textrm{mm}^2$. From the results of fracture surface analysis, the increase of friction pressure could remarkably decrease the force and the time to be normally acted on weld interface. The W particles which were included in the plastic zone of Cu side could induce fracture adjacent to the weld interface because their existance in Cu induces a decrease in available section area and an increase in notch effect. Therefore, the tensile strength was decreased at high friction pressure (6kgf/$\textrm{mm}^2$) because the destruction of W was increased by an increase in mechanical force and crack was formed at weld interface.

• Clinics in Shoulder and Elbow
• /
• 제2권1호
• /
• pp.84-87
• /
• 1999

저자들은 충돌 증후군 진단하에 관절경적 견봉하 감압술 중 우연히 발견된 Buford 복합체를 가진 환자를 본 후, 술후 이 환자를 추시한 결과가 Buford 복합체가 없는 다른 환자의 경우와 크게 다르지 않은 것을 보고, 충돌 증후군의 증상을 보이는 환자에서 삭형 중 견와상완 인대와 전상방견와 순의 결여가 있는 경우 이 복합체가 술후 예후에 영향을 미치지 않는 것으로 결론을 내리고 이를 보고하는 바이다.

• The Korean Journal of Pain
• /
• 제8권1호
• /
• pp.149-151
• /
• 1995

Piriformis syndrome is a syndrome of low back and leg radiating pain thought to be due to a chronic contracture of the piriformis muscle that causes irritation of the sciatic nerve. The piriformis muscle is a flat pyramidal muscle, an external rotator and abductor of the hip, originating from the front of the sacrum and inner aspect of the sacroiliac joint, then passes laterally out of the sciatic notch to attach posteriorly to the greater trochanter of the femur, the sciatic nerve passes between the two bellies of the muscle. Mechanical irritation of the sciatic nerve by an inflammatory reaction of the piriformis muscle and its fascia at this pelvic level causes pain to radiate in the dermatomal regions of the nerve roots similar to that disk entrapment. diagnosis of piriformis syndrome is made primary on the basis of history and clinical examination. The incidence is considerably higher in women, with the reported ratio of women to men of 6:1. These patients frequently present with associated symptoms of pelvic pain and/or dyspareunia. Symptoms are usually unilateral but occasionally be bilateral. We had a 42 year-old woman patient with low back and left leg radiating pain and dyspareunia treated by caudal steroid and local anesthetic.