• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.83-86
• /
• 2004

Carbon nanotube (CNT) tips in tapping mode atomic force microscopy (AFM) enable very high-resolution imaging, measurements, and manipulation at the nanoscale. We present recent results based on experimental analysis that yield new insights into the dynamics of CNT probe tips in tapping mode AFM. Experimental measurements are presented of the frequency response and dynamic amplitude-distance data of a high-aspect-ratio multi-walled (MW) CNT tip to demonstrate the non-linear features including tip amplitude saturation preceding the dynamic buckling of the MWCNT. Surface scanning is performed using a MWCNT tip on a SiO$_2$ grating to verify the imaging instabilities associated with MWCNT buckling when used with normal control schemes in the tapping mode. Lastly, the choice of optimal setpoints for tapping mode control using CNT probe tip are discussed using the experimental results.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 II
• /
• pp.1370-1375
• /
• 2001

Substructure coupling or component mode synthesis may be employed in the solution of dynamic problems for structure. The model is partitioned into several subdomains. and a generalized Craig-Bampton representation is derived. In this paper the mode sets(normal modes. constraint modes) have been employed for model reduction. A generalized model reduction procedure has been described. Those reduction methods which adapt constraint modes have been described in detail. As examples. a flexible structure and a 10 DOF damped system are analyzed. Comparison with a conventional reduction method based on a complete model has been made via eigenpairs and dynamic responses.

• Ocean Systems Engineering
• /
• 제10권1호
• /
• pp.67-86
• /
• 2020

The main goal of this study is to investigate the free vibration analysis of a large sag catenary with application to the jumper in hybrid riser system. The equation of motion is derived by using the variational method based on the virtual work principle. The finite element method is applied to evaluate the numerical solutions. The large sag catenary is utilized as an initial configuration for vibration analysis. The nonlinearity due to the large sag curvature of static configuration is taken into account in the element stiffness matrix. The natural frequencies of large sag catenary and their corresponding mode shapes are determined by solving the eigenvalue problem. The numerical examples of a large sag catenary jumpers are presented. The influences of bending rigidity and large sag shape on the free vibration behaviors of the catenary jumper are provided. The results indicate that the increase in sag reduces the jumper natural frequencies. The corresponding mode shapes of the jumper with large sag catenary shape are comprised of normal and tangential displacements. The large sag curvature including in the element stiffness matrix increases the natural frequency especially for a case of very large sag shape. Mostly, the mode shapes of jumper are dominated by the normal displacement, however, the tangential displacement significantly occurs around the lowest point of sag. The increase in degree of inclination of the catenary tends to increase the natural frequencies.

• 비파괴검사학회지
• /
• 제29권6호
• /
• pp.570-578
• /
• 2009

Excitation and propagation of guided waves are very complex problems in pipes due to their dispersive nature. Pipes are commonly used in the oil, chemical or nuclear industry and hence must be inspected regularly to ensure continued safe operation. The normal mode expansion(NME) method is given for the amplitude with which any propagating waveguide mode is generated in the pipes by applied surface tractions. Numerical results are calculated based on the NME method using different sources, i.e., non-axisymmetric partial loading and quasi-axisymmetric loading sources. The sum of amplitude coefficients for 0~nineth order of the harmonic modes are calculated based on the NME method and the dispersion curves in pipes. The superimposed total field which is namely the angular profile, varies with propagating distance and circumferential angle. This angular profile of guided waves provides information for setting the transducer position to find defects in pipes.

• Structural Engineering and Mechanics
• /
• 제89권3호
• /
• pp.253-263
• /
• 2024

Slope stability is generally paid more attention to in slope protection works, especially for slope containing weak layers. Two indexes of safety factor and failure model are selected to perform slope stability. Moreover, the finite element limit analysis method comprehensively combines the advantage of the limit analysis method and the finite element method obtaining the upper and lower bounds of the safety factor and the failure mode under the slope stability limit state. In this study, taking a waste dump containing a weak layer as an engineering background, the finite element limit analysis method is adopted to explore the potential failure mode. Meanwhile, the sensitivity analysis of slope stability is performed on geometrical and geotechnical parameters of the waste dump. The results show that the failure mode of the waste dump slope is two wedges if the weak layer is located on the ground surface (Model A), while the slope can be observed as three wedges failure if the weak layer is below the ground surface (Model B). In addition, both failure modes are highly sensitive to the friction angle of the weak layer and the shear strength of waste disposal, and moderately sensitive to the heap height, the dip angle and cohesion of the weak layer, while the toe cutting has limited effect on the slope stability. Moreover, the sensitivity to the excavation of the ground depends on the location of the weak layer and failure mode.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1990년도 추계학술대회
• /
• pp.25-28
• /
• 1990

We tested the ability of two-dimensional echocardiograms of complete heart cycle in closed-chest human to discriminate between normal and infarcted myocardium using fixed window, Inter- and Intra-frame analysis. The results show that statistical parameter, MEAN, second order gray level statistics parameter, ASM and proposed parameter, HGE, I.T, can quantitatively distinguish between normal and Infarcted regions. The manner in which these parameters vary over the cardiac cycle is also a good indicator of the state of myocardium. The infarcted areas yield regions of higher Intensity throughout the cardiac cycle. Whereas, normal tissue demonstrates greater variability throughout the cardiac cycle.

• 한국공작기계학회논문집
• /
• 제10권5호
• /
• pp.60-70
• /
• 2001

In multi-purpose lathe, the design of tilting turret slide system has an important and critical role to enhance accuracy of the machining process. Tilting turret unit is traveled by 3-axis slide systems. There is a need to design this part very carefully. In this research, 3-axis sliding system with tilting turret unit is modeled by considering the element dividing, material proprties, and boundary conditions with PATRAN. Normal mode and frequency analysis of each structures such as saddle, cared, and turret are simulated by NASTRAN, for the purpose of developing the effective design. The results of mode analysis and frequency analysis are visualized with PATRAN, and the design method which can solve the resornance problem by eigenvalues and eigenvectors of each axis is developed as well.

• International Journal of Advanced Culture Technology
• /
• 제8권2호
• /
• pp.159-164
• /
• 2020

The response analysis of frame structure with open section beams considering warping conditions and short duration load have been performed. When a beam of frame structure is subjected under torsional moment, the cross section will deform a warping as well as twist. For some thin-walled sections warping will be large, and accompanying warping restraint will induce axial and shear stresses and reduce the twist of beam which stiffens the beam in torsion. Because of impact or blast loads, the wave propagation effects become increasingly important as load duration decreases. This paper presents that a warping restraint in finite element model effects the behavior of beam deformation, dynamic mode shape and response analysis. The computer modelling of frame is discussed in linear beam element model and linear thin shell element model, also presents a correlation between computer predicted and actual experimental results for static deflection, natural frequencies and mode shapes of frame. A method to estimate the number of normal modes that are important is discussed.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 추계학술대회 논문집
• /
• pp.675-676
• /
• 2012

• 한국방재안전학회논문집
• /
• 제7권1호
• /
• pp.43-50
• /
• 2014

본 논문은 신뢰성 이론에 기초하여 철골보의 단경간 및 2경간 연속보의 파손확률을 결정하였다. 계산식에서 철골보에 가해지는 하중은 정규 분포로 가정하여 진행되었으며, 파손확률의 변화를 확인하기 위해 보의 중앙범위에 적용하는 하중을 보의 1대 1과 1대 2로 분할된 지점에 배치하였다. 보의 끝부분의 경계 결합조건 역시 연구에 포함되었다. 연구 결과 파손확률이 있는 보에 대한 결합조건 및 파손확률은 2차 분석에 따라 그 중요도가 낮은 것으로 나타났다. 결론적으로 일부의 경우를 제외하고 보의 파손확률은 보 양단의 경계조건에 따라 차이가 있는 것으로 나타났다.