• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.9
• /
• pp.82-88
• /
• 2006

In order to effectively reduce thermal loads on regenerative cooled walls, fuel cooling injectors and film cooling devices have often been employed. The present study has established a numerical methodology for prediction of performance and near-wall temperature distribution taking into account the nonuniform mixing due to these additional cooling devices. A correction procedure for main propulsive parameters has also been proposed based on comparison between prediction and experimental data. Under the computational framework of this study, the predicted results were in good agreement with hot-firing test data for a 30 tonf-class full-scale combustor at the design and off-design conditions. As a consequence, the present numerical method is expected to be useful for design and evaluation of regenerative cooled liquid rocket thrust chambers.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.466-469
• /
• 2002

In the sintering of YIG, abnormal grain growth phenomena was observed. This abnormal grain growth is related to the sintering temperature in this experiment. In the sintering below 145$0^{\circ}C$., the sintered body showed narrow size distribution. However, in the sintering at 145$0^{\circ}C$, a few grains grew rapidly with respect to other grains, and bimodal size distribution was appeared. Liquid phase was not observed far from the abnormally grown large grains, but only near the large grains. This means that the abnormal grain growth was caused by the nonuniform distribution of liquid phase which promote the grains growth. This nonuniform distribution of liquid phase was thought to be due to the nonuniform mixing of the starting materials. This abnormal grain growth was suppressed by enhance the compositional uniformity by multiple calcination.

• Nuclear Engineering and Technology
• /
• v.29 no.3
• /
• pp.186-195
• /
• 1997

When asymmetric thermal-hydraulic conditions occur between cold legs, the core inlet temperature will be nonuniform if the coolant is not mixed perfectly in the lower plenum. These uneven core inlet conditions may induce the change in core power distribution. Thus realistic prediction of thermal mixing is important in such abnormal conditions. In this study, reactor internals, which are scaled down as to conserve the flow area ratio, are set up in the model of KORI Unit 1 with the scaling factor of 1/710 by volume and coolant temperatures are measured beneath the lower core plate. Based on experimental results, the ability of COMMIX-1B code to simulate the coolant mixing phenomena in the lower plenum is estimated. The results show that complete mixing never occurs in any conditions and the mixing pattern is characterized according to the plant type.

• Nuclear Engineering and Technology
• /
• v.49 no.1
• /
• pp.71-81
• /
• 2017

When an integral pressurized water reactor is operated under low power conditions, once-through steam generator group operation strategy is applied. However, group operation strategy will cause nonuniform coolant flow distribution at the core inlet and lower plenum. To help coolant flow mix more uniformly, a flow mixing chamber (FMC) has been designed. In this paper, computational fluid dynamics methods have been used to investigate the coolant distribution by the effect of FMC. Velocity and temperature characteristics under different low power conditions and optimized FMC configuration have been analyzed. The results illustrate that the FMC can help improve the nonuniform coolant temperature distribution at the core inlet effectively; at the same time, the FMC will induce more resistance in the downcomer and lower plenum.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12
• /
• pp.1131-1135
• /
• 2003

In the sintering of YIG, abnormal grain growth phenomena were observed. This abnormal grain growth is related to the sintering temperature in this experiment. In the sintering below 1450$^{\circ}C$, the sintered body showed narrow size distribution. However, in the sintering at 1450$^{\circ}C$, a few grains grew rapidly with respect to other grains, and bimodal size distribution was appeared. From the observation of the microstructure, liquid phase was not observed far from the abnormally grown large grains, but only near the large grains. This means that the abnormal grain growth was caused by the nonuniform distribution of liquid phase which promote the grains growth. Because the growth rate of grains near the liquid phase is much higher than that of the other grains, a few grains grow rapidly. This nonuniform distribution of liquid phase was thought to be due to the nonuniform mixing of the calcined powders. This abnormal grain growth was suppressed by enhancement of the compositional uniformity by multiple calcination.

• Journal of Korean Ophthalmic Optics Society
• /
• v.2 no.1
• /
• pp.91-95
• /
• 1997

A General equation is developed for the efficiency of an integrating sphere with a nonuniform coating. The only assumptions are that the interior is a perfect sphere and that all areas reflect perfectly diffusely. The general equation are examined for the basic applications of integrating spheres as mixing mechanisms in hemispherical reflectance measurements and in absolute reflectance techniques.

• Journal of Korean Society of Water and Wastewater
• /
• v.22 no.6
• /
• pp.689-696
• /
• 2008

In a water treatment process a complete and homogeneous dispersion of the coagulants in the raw water could be most important factor. This research was performed to evaluate coagulation performance of the in-line-orifice mixer which was recently introduced as a rapid mixing device. The test was to determine the actual coagulant dispersion distribution on the overall cross-section at a distance of 1.6~3D from the chemical injection point by measuring zeta potential. From the results of zeta potential test, it was shown that the coagulant dispersion within the in-line orifice mixer was occurred very unevenly. The results have confirmed that it is necessary to increase the velocity of coagulants injection or pressurized water rates, in order to reduce nonuniform distribution of chemicals.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.1
• /
• pp.67-74
• /
• 2013

A jet in a crossflow (JICF) has been extensively studied because of its wide applications in technological systems, including fuel injection into a ram-combustor. However, in the case of insufficient mixing performance of the liquid jet into the crossflow, the flame in a ram-combustor is unstable. In this study, the nonuniform flame and combustion instabilities due to lack of mixing performance were experimentally investigated. By performing correlations to predict the penetration height and break-up point, the spray and mixing characteristics of JICF have been studied. In particular, the improved correlations of penetration height are proposed in two distinctive domains depending on the X/d location of the crossflow.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1262-1263
• /
• 2011

Sulfur hexafluoride is the most commly used insulation gas in electrical systems. Gas insulated systems are widely used in the electric power industry for transmission and distribution of electrical energy. When $SF_6$ was first discovered, the potential application was only considered for insulation because of good dielectric properties. But the widespread use of $SF_6$ gas by electric power and other industries has led to increase concentrations of $SF_6$ gas in the atmosphere. This concern as to possible effects on global warming because $SF_6$ is a potent greenhouse gas. That's why firstly we studied uniform and nonuniform field property by mixing $SF_6$ and N2 gas. This paper presents the dielectric strength and insulating property for particle contamination under $SF_6/N_2$ mixtures. Two types of mixed gases(50% $SF_6$_50%$N_2$, 20% $SF_6$_80%$N_2$) were applied. We performed tests for the length and shape of particle. Test gas pressure is from 0.3 to 0.7 Mpa. The study was conducted to develop environment-friendly insulating material for GIS that can reduce $SF_6$ gas and make a design criteria for mixtures.

• Journal of the Korean Society of Visualization
• /
• v.19 no.3
• /
• pp.69-76
• /
• 2021

Printed circuit heat exchanger (PCHE) is a compact heat exchanger with good heat transfer performance, high structure integrity, and reliability over a wide range of temperatures and pressures. Instead of the traditional zigzag and straight shape channel, the sinusoidal shape channel was adopted in this study to investigate the relation of thermal-hydraulic performance and waviness factors (period and amplitude). The local flow characteristics and the heat flux distribution were compared to verify the effects of period and amplitude on heat transfer performance. As the period of channel becomes shorter, the rapid change of the flow direction can produce high flow separation around the corner leading to the disturbance of the boundary layer opposite wall. The nonuniform distribution of flow velocity appeared around the corner positions can promote fluid mixing and lead to higher thermal performance. An evaluation index was used to compare the comprehensive performance of PCHE considering the Nusselt number and Fanning factor. Based on the simulation results, the optimal design parameters of PCHE channel shape were found that the channel with an equivalent bending angle of 15° offers the highest heat flux capacity.