• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.6
• /
• pp.496-501
• /
• 2007

In order to enhance sintering characteristics on the $ZnO-Pr_6O_{11}$ based multilayer chip varistors (MLVs), a response surface analysis using central composite design method were carried out. As a result, varistor voltage($V_{1mA}$), nonlinear coefficient ($\alpha$), leakage current ($I_L$) and capacitance (C) were considered to be mainly affected by sintered temperature and holding time. MLVs sintered at $1200^{\circ}C$ and above $1200^{\circ}C$ revealed poor electrical characteristics, possibly due to the reaction between electrode materials(Pd) and $ZnO-Pr_6O_{11}$ based ceramics. On the sintering temperature range $1150{\sim}1175^{\circ}C$, nonlinear coefficient ($\alpha$) and leakage current ($I_L$) were shown to be $60{\sim}69$ and below $0.3{\mu}A$, respectively. In particular, MLVs sintered at $1175^{\circ}C$, 1.5 hr and $2^{\circ}C/hr$ (cooling speed) showed stable ESD(Electrical Static Discharge) characteristics under the condition of 10 times at 8 Kv with deviation varistor voltage, and deviation nonlinear coefficient were 0.3% and 0.33% (at positive), 0.55% (at negative), respectively.

• Proceedings of the IEEK Conference
• /
• 2002.07c
• /
• pp.1878-1881
• /
• 2002

The capacitance of nonlinear component such as a CMOS inverter varies largely around the threshold voltage. We measured the far-end crosstalk of two parallel microstrip lines with the CMOS inverter load near the threshold voltage of the CMOS inverter, The negative voltage of the crosstalk agrees with that for a 4pF capacitor toad. The positive voltage of the crosstalk hardly changes of the amplitude of the input step voltage.

• 전기의세계
• /
• v.28 no.1
• /
• pp.53-58
• /
• 1979

In the microwave heating system, a ferroresonant transformer is used to regulate the magnetron power fluctuation. For the simplification, nonlinear characteristics of the transformer and the magnetron are idealized to be piecewise linear. Dipped peak shape of the magnetron current is explained qualitatively by considering the fundamental and third harmonic frequency components in the circuit. Design equations providing the values of the leakage inductance, turn ratio of the transformer and the capacitance are derived analytically by cosnidering the fundamental frequency component only. The ferroresonant transformer is designed to obtain a required regulation and high input power factor from the derived design equations, and analytical calculations are compared with experimental measurements.

• Proceedings of the IEEK Conference
• /
• 2003.07c
• /
• pp.2835-2838
• /
• 2003

We study the characteristics of oscillating in non-autonomous condition and the conducted noise generation in a RL-photocoupler circuit. This circuit may be shown a period-doubling and a chaos dynamics under any specific conditions of input circuit. But, the relationship between input signals and output signals is different according to the amplitude of driving input voltage. Then, the oscillation noise was analyzed with respect to both the frequency and the amplitude of an external ac signal and do values. The results show that the noise-induced oscillations for falling and rising cycles induced by kick-back effect in an inductor, nonlinear capacitance, nonlinear resistance and charge storage time in a diode and an LED. We also compared the simulation with the experimental results.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.10
• /
• pp.1697-1701
• /
• 2016

The leakage conduction and critical voltage characteristic of ZnO ceramic were investigated as a function of $Sb_2O_3$ concentration. Leakage conduction in the ohmic region increased with increasing $Sb_2O_3$ concentration and was attributed to the potential barrier height. The nonlinear coefficient increased with an increasing amount of $Sb_2O_3$. It was found that increases in the apparent critical voltages were associated with the lowered donor concentration in the grain boundary of between two ZnO grains. And the decrease of donor concentration on doping with $Sb_2O_3$ additive was attributed to the lowered capacitance in the grain boundary layer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.561-564
• /
• 2000

Silicon capacitive pressure sensor has been fabricated by using electrochemical etching stop and silicon-to-glass electrostatic bonding technique. A diaphragm structure is designed to compensate the nonlinear response. A cavity is etched into the silicon to the depth of 2$\mu\textrm{m}$ by anisotropic etching in 20wt.% TMAH solution at 80$^{\circ}C$. A fabricated sensor showed 3.3 pF zero-pressure capacitance, 297 pp.m/mmHg sensitivity, and a 7.4 7%F.S. nonlinear response in a 0-1 kgf/cm$^2$pressure range.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.5
• /
• pp.412-418
• /
• 2002

In this paper, the authors present the simulation results and the experimental considerations on the effects of the effects of the VCO oscillation characteristics caused by varying the length of the MSL and the composition capacitance of LC resonation circuity. Simulation was accomplished by nonlinear RF circuit simulator for designing and analyzing the RF characteristis of VCO. The samples with 3 different MSL lengths of which the length is 140mil, 280mil and 560mil respectively were fabricated by screen printing process. The oscillation frequency of each sample(VCO) was tuned to UHF band (750MHz~900MHz) by varying the capacitance of LC resonator circuit. The experimental results showed that the values of phase noise were -82, -93, -97[dBc/Hz] at 50[kHz] offset frequency, the pushing figures were 114, 94, 318[kHz] at applied voltage of $3\pm0.15$[V] and the harmonics were -21, -16, -13[dBc] for MSL lengths of 140mil 280mil, 560mil respectively. The frequency and output variation width were 779~898[MHz], -36~-33[dBm] for MSL with 140mil length; 818~836[MHz], -27.19~27.06[dBm] for 280mil; 751.54~751.198[MHz], -33.44~-33.31[dBm] for 560mil.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.5
• /
• pp.860-865
• /
• 2010

When a circuit breaker is opened, a large capacitance around the buses, the circuit breaker and the potential transformer (PT) might cause PT ferroresonance. During PT ferroresonance, the iron core repeats saturation and unsaturation even though the supplied voltage is a rated voltage. This paper describes an analytical analysis of PT ferroresonance in the transient-state. To analyze ferroresonance analytically, the iron core is modelled by a simplified two-segment core model in this paper. Thus, a nonlinear ordinary differential equation (ODE) for the flux linkage is changed into a linear ODE with constant coefficients, which enables an analytical analysis. In this simplified model, each state, which is either saturated or unsaturated state, corresponds to one of the three modes, i.e. overdamping, critical damping and underdamping. The flux linkage and the voltage in each state are obtained analytically by solving the linear ODE with constant coefficients. The proposed transient analysis is effective in the more understanding of ferroresonance and thus can be used to design a ferroresonance prevention or suppression circuit of a PT.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.42_43
• /
• 2009

Ferroresonance is a resonance condition between a nonlinear iron core of a potential transformer (PT) and a capacitance. It can lead to PT voltages several times the normal equipment ratings, and cause the isolation broken and damage to equipments near the PT. This paper proposes a analysis method of PT ferroresonance in the time domain. Based on the simplified equivalent circuit, a differential equation was found and the flux was calculated when ferroresonance generates. The forced response and natural response were also analyzed. The performance of proposed analysis method was verified with the EMTP-RV generated data. The method can help analysis chaotic ferroresonance and periodic ferroresonance.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.635-640
• /
• 1996

A thermo-elastic system in the production machine has highly nonlinear dynamic characteristics. In general, the finite element method is utilized for accurate analysis. However, it requires large computing time. Thus, thermo-elastic systems are usuallymodeled as electric and fluid system using lumped para,eter. In this paper. we propose the bondgraph model and transient simulation methodology of thermo-elastic system in consideration of various boundary and joint contact conditions. Consequently, the proposed method ensures a possibility of its on-line compensation about undesirable phenomena by using real time estimate process and electronic cooling device for thermal appropriate behavior. Thermo-elastic model consisting of bush and shaft including contact condition is presented.