• Journal of Environmental Science International
• /
• v.18 no.2
• /
• pp.197-203
• /
• 2009

The aim of this study is to calculate process emission of GHGs(greenhouse gases) in nonferrous-metal industry, such as Zn, Pb, Cu and Ni. In addition, variation and emission of GHGs generated from these company were defined. And then, GHGs algorithm and calculation formular which were considered as production process in each part of nonferrous-metal industry were developed to develop calculation program of GHGs emission. These algorithm and calculation formular would present fundamental direction about other nonferrous-metal industry in the future.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.312-313
• /
• 2006

The primary aim pursued by the preparation of separation membrane is the preparation of the membrane thin as well as with no defect. The field-flow fractionation deposition is a new molding technology which can overcome the traditional disadvantages such as multi-preparation to the preparation of great area of separation membrane with no defect. Therefor the mainly ingredients which influence the appearance and performance of titanium membrane layer are investigated by scanning electricity mirror (SEM) as well as porous material testing instrument: powder performance prepared and confected; selection of supporting body; sintering system such as temperature and time. It is shown that the membrane thickness can be controlled at $50{\mu}m$ or so; the filtration precision mainly rests with powder performance and selection of supporting body and little sintering system

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.104-105
• /
• 2006

The low-cycle fatigue performance and fracture of the P/M Ti-Fe-Mo-Al-Nd Alloys after sintering and forging have been studied. The linear regression equation of low-cycle fatigue lifetime has been obtained; the fatigue performances are objected under two different conditions. The fatigue fracture surface is analyzed by SEM. The low-cycle fatigue behavior of the P/M titanium alloy has been discussed.

• Progress in Superconductivity and Cryogenics
• /
• v.21 no.2
• /
• pp.10-14
• /
• 2019

In order to improve resource value, separation of nonferrous metals obtained from crushed materials of home appliances is required. In this study, we aimed to develop a continuous separation system by magneto-Archimedes method using magnetic fluid as a medium and the permanent magnet as a magnetic field source. Firstly, the separation conditions were examined in which only copper is settled and the difference in levitation positions between aluminum and other metals are over 1 cm. Based on the results, levitation experiment of each metal and separation experiment from the mixture of nonferrous metals were confirmed. The separation experiment showed that the continuous separation of copper and aluminum from a mixture of nonferrous metals is possible.

• Journal of Powder Materials
• /
• v.20 no.5
• /
• pp.355-358
• /
• 2013

Micro trench structures are applied in gratings, security films, wave guides, and micro fluidics. These micro trench structures have commonly been fabricated by micro electro mechanical system (MEMS) process. However, if the micro trench structures are machined using a diamond tool on large area plate, the resulting process is the most effective manufacturing method for products with high quality surfaces and outstanding optical characteristics. A nonferrous metal has been used as a workpiece; recently, and hybrid materials, including polymer materials, have been applied to mold for display fields. Thus, the machining characteristics of polymer materials should be analyzed. In this study, machining characteristics were compared between nonferrous metals and polymer materials using single crystal diamond (SCD) tools; the use of such materials is increasing in machining applications. The experiment was conducted using a square type diamond tool and a shaper machine tool with cutting depths of 2, 4, 6 and 10 ${\mu}m$ and a cutting speed of 200 mm/s. The machined surfaces, chip, and cutting force were compared through the experiment.

• Journal of Environmental Health Sciences
• /
• v.18 no.1
• /
• pp.1-5
• /
• 1992

A study was performed to measure the heavy metal concentrations of suspended particles in iron castings during February, 1990. The heavy metal concentrations were analyzed using patricles atomic absorption spectrophotometer. The results were as fellows 1. The concentrations of suspended paticles by casting process were at furnace 4.19mg/m$^{3}$ at pouring 2.93mg/m$^{3}$ at nonferrous furnace 3.90mg/m$^{3}$, at molding 1.17mg/m$^{3}$, jung ja 2.23mg/m$^{3}$, desanding 5.42mg/m$^{3}$, sand treatment 4.82mg/m$^{3}$, finishing 1,20mg/m$^{3}$. 2. Among the total of 8 iron casting workplaces, the concentrations Fe of furnace was 0.36mg/m$^{3}$, Cu of nonferrous furnace 0.02mg/m$^{3}$, Pb of pouring 0.02mg/m$^{3}$, Cr of desanding 0.01mg/m$^{3}$ and Mn of furnace 0.03mg/m$^{3}$.

• Journal of Korea Foundry Society
• /
• v.21 no.2
• /
• pp.93-103
• /
• 2001

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.5 no.4
• /
• pp.27-32
• /
• 2006

This study aims to find the optimal cutting conditions, when are nonferrous metals(aluminum and silicon) are machined with diamond tool of diamond turning machine. Diamond turning machine has been widely used in manufacturing optical reflectors of nonferrous metals. Such as aluminium and copper are easy to be machined because of their proper ductility. But optical crystals being discussed here are characterized by their high brittleness which makes it difficult to obtain high quality optical surfaces on them. The purpose of this study is to find the optimum machining conditions for ductile cutting of silicon and aluminium.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.18 no.5
• /
• pp.483-490
• /
• 2009

The objective of this development project is to localize an automatic molten metal supplier that has been distributed by WESTOMAT, Germany, throughout the world. To achieve this purpose, an energy-saving pressurized dosing furnace and molten metal differential pressure control system that Is able to automatically supply a determined quantity of aluminum molten metal were developed. The localized equipment was installed in a site. Also, the results of the test operation of this equipment can be summarized as follows: It was able to improve the productivity because there were small decreases in supplying speeds and small losses in wastes compared to the existing mechanical molten metal supplier. Also, it was able to minimize the cost in maintenances due to the direct application of high temperature molten metals to molds. In addition, there were small energy losses due to the use of high thermal insulators compared to the existing reverberating furnace and able to prolong the life-time of furnaces and produce good quality nonferrous metals because it represented small carbon refractories and alumina in applied molten metals. Furthermore, it demonstrated no particular differences by objectively comparing it with the product by WESTOMAT.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.11a
• /
• pp.149-151
• /
• 2012

Changes in the price of materials in construction projects is one of the important variables. Therefore, measures are necessary to respond to the demand and supply of materials and price instability. In previous studies, mainly of ready-mix concrete and steel beam analysis was carried out. However, a study of non-ferrous material prices are still insufficient. So, in this study, the researcher identified the causal relationship between the construction cost and non-ferrous materials prices. Construction Cost Index was selected as a proxy variable of construction cost.