• Journal of the Korean Society for Nondestructive Testing
• /
• v.32 no.5
• /
• pp.518-525
• /
• 2012

In this study, the feasibility of hyperspectral reflectance imaging technique was investigated for the discrimination of viable and non-viable lettuce seeds. The spectral data of hyperspectral reflectance images with the spectral range between 750 nm and 1000 nm were used to develop PLS-DA model for the classification of viable and non-viable lettuce seeds. The discrimination accuracy of the calibration set was 81.6% and that of the test set was 81.2%. The image analysis method was developed to construct the discriminant images of non-viable seeds with the developed PLS-DA model. The discrimination accuracy obtained from the resultant image were 91%, which showed the feasibility of hyperspectral reflectance imaging technique for the mass discrimination of non-viable lettuce seeds from viable ones.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.4
• /
• pp.323-330
• /
• 2009

The objective of this research was to develop a practical integrated approach using extracted features from electrical resistance measurements and coupled electromechanical models of damage, for in-situ damage detection and sensing in carbon fiber reinforced plastic(CFRP) composites. To achieve this objective, we introduced specific known damage (in terms of type, size, and location) into CFRP laminates and established quantitative relationships with the electrical resistance measurements. For processing of numerous measurement data, an autonomous data acquisition system was devised. We also established a specimen preparation procedure and a method for electrode setup. Coupon and panel CFRP laminate specimens with several known damage were tested. Coupon specimens with various sizes of artificial delaminations obtained by inserting Teflon film were manufactured and the resistance was measured. The measurement results showed that increase of delamination size led to increase of resistance implying that it is possible to sense the existence and size of delamination. A quasi-isotropic panel was manufactured and electrical resistance was measured. Then three different sizes of holes were drilled at a chosen location. The panel was prepared using the established procedures with six electrode connections on each side making a total of twenty-four electrodes. Vertical, horizontal, and diagonal pairs of electrodes were chosen and the resistance was measured. The measurement results showed the possibility of the established measurement system for an in-situ damage detection method for CFRP composite structures.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.35 no.2
• /
• pp.141-149
• /
• 2015

In the fabrication of electronic circuits used in electronic products, molybdenum thin films are deposited on semiconductors to prevent oxidation. During the deposition, the presence of a particle or dust at the interface between the thin film and substrate causes the decrease of adhesion, performance, and life cycle. In this study, a damage measurement targeting two kinds of glass substrate, with and without particles, was performed in order to measure the change in the molybdenum thin film deposition area in the presence of a particle. Clean and dirty molybdenum thin film specimens were fabricated and directly deposited on a substrate using the sputtering method, and a reflection-type digital holographic interferometer was configured for measuring the damage. Reflection-type digital holography has several advantages; e.g., the configuration of the interferometer is simple, the measurement range can be varied depending on the magnification of a microscopic lens, and the measuring time is short. The results confirm that reflection-type digital holography is useful for the measurement of the damage and defects of thin films.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.18 no.5
• /
• pp.365-372
• /
• 1998

The method of measuring the nonlinear effect of ultrasonic waves is suggested as a new approach for the effective evaluation of material degradation. In sonic wave propagation, the existence of nonlinear effect can be demonstrated by the generation of higher order harmonic waves. So, at first, the mechanism of generating higher order harmonic components due to nonlinear effect was explained by using nonlinear elasticity. Next, we attempted to measure how much of the higher order harmonic component was generated in the degraded material. For this purpose, a measurement system mainly based on a high-powered nonlinear ultrasonic signal analysis system was constructed, and SS41 and SS45 specimen intentionally degraded by tensile load and fatigue load were tested. From the results, we confirmed that the measurement of nonlinear acoustic effect may be useful for the evaluation of material degradation.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.14 no.1
• /
• pp.7-15
• /
• 1994

The two-dimensional elastoplastic analysis was peformed to reveal a detail residual stress distribution of ceramic/metal joint specimen using finite element method and X-ray method. The highest tensile residual stress, ${\sigma}_x$ perpendicular to the interface appeared at the edge of the ceramic near the interface. In the vicinity of the interface, the high stress concentration occurs and residual stress distributes three-dimensionally. Therefore, the measured stress distribution differed remarkably from the result of the two-dimensional finite-element analysis. Especially at the center of the specimen near the interface, the residual stress, ox obtained from the finite element analysis was compressive, whereas X-ray measurement yielded tensile ${\sigma}_x$. Therefore, it is also attempted to investigate the finite element model for the prediction of residual stress ${\sigma}_x$ distributed nearly the interface of joint.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.32 no.2
• /
• pp.149-154
• /
• 2012

The size and distribution of welding residual stress and welding deformation in welding structures have an effect on various sorts of damage like brittle failure, fatigue failure and stress corrosion cracking. So, research for this problem is necessary continuously. In this study, non-destructive technique using laser electronic speckle pattern interferometry, plate of welding specimen according to the external load on the entire behavior of residual stress are presented measurement techniques. Once, welding specimen force tensile loading, using electronic speckle pattern interferometry is measured. welding specimen of base metal and weld zone measure strain from measured result, this using measure elastic modulus. In this study, electronic speckle pattern interferometry use weld zone and base metal parts of the strain differences using were presented in residual stress calculated value, This residual stress value were calculated by numerical calculation. Consequently, weld zone of modulus high approximately 3.7 fold beside base metal and this measured approximately 8.46 MPa.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.35 no.1
• /
• pp.18-24
• /
• 2015

Train positioning detection information is fundamental for high-speed railroad inspection, making it possible to simultaneously determine the status and evaluate the integrity of railroad equipment. This paper presents the results of measurements and an analysis of an inertial measurement unit (IMU) used as a positioning detection sensors. Acceleration and angular rate measurements from the IMU were analyzed in the amplitude and frequency domains, with a discussion on vibration and train motions. Using these results and GPS information, the positioning detection of a Korean tilting train express was performed from Naju station to Illo station on the Honam-line. The results of a synchronized analysis of sensor measurements and train motion can help in the design of a train location detection system and improve the positioning detection performance.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.4
• /
• pp.290-298
• /
• 2014

Ultrasonic thickness measurement is a non-destructive method to measure the local thickness of a solid element, based on the time taken for an ultrasound wave to return to the surface. When an element is very thin, it is difficult to measure thickness with the conventional ultrasonic thickness method. This is because the method measures the time delay by using the peak of a pulse, and the pulses overlap. To solve this problem, we propose a method for measuring thickness by using the power cepstrum and the minimum variance cepstrum. Because the cepstrums processing can divides the ultrasound into an impulse train and transfer function, where the period of the impulse train is the traversal time, the thickness can be measured exactly. To verify the proposed method, we performed experiments with steel and, acrylic plates of variable thickness. The conventional method is not able to estimate the thickness, because of the overlapping pulses. However, the cepstrum ultrasonic signal processing that divides a pulse into an impulse and a transfer function can measure the thickness exactly.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.1
• /
• pp.20-27
• /
• 2017

The aim of this paper is to present the modulus of elasticity of $E_L$, $E_R$, $E_T$ along three principal axis of softwood dimension lumber by nondestructive method. Ultrasonic measurement was carried out on defect free wood samples taken by the Japanese Larch, SPF (spruce-pine-fir) and Hem-fir $2{\times}4s$. The ultrasound velocities were measured to calculate young's moduli and it was derived elastic constants for each wood samples using the ultrasound velocities and densities of wood. From the test, $E_L$ was much greater than $E_R$ and $E_T$. $E_R/E_T$ ratios were about 1.3. The high density wood had high young's moduli in three principal axis and the difference in young's moduli between species was greater in transverse direction than longitudinal direction. The anisotropy of the lumber was presented through the calculated elastic moduli and compliances matrix in diagonal term were determined by inverting the stiffness matrix.

• Proceedings of the Korean Society of Near Infrared Spectroscopy Conference
• /
• 2001.06a
• /
• pp.1155-1155
• /
• 2001

The quality of agricultural products is very important factor for consumers. In Japan, quality is sometimes more important than cost. Usually, the quality of fresh food products is determined in terms of shape, color, size, etc. However, these indices are not always associated with taste, leaving consumers to complain. Recently, two types of the fruit quality meter (a tabletop type - K-FS200 and a portable type - K-BA100, Kubota Corp.) using NIR technology were introduced in Japan. A tabletop instrument is for post harvest use and a portable one is for precision agriculture use. The both meters use the NIR region from 600nm to 1000nm in the interactance mode to determine quality factors related to taste. The instruments can measure sugar content and acidity of such fruit as apples, tomatoes, tangerines and other fruits. The measurement is timely, nondestructive and precise. For example, the coefficient of variation (CV) is less than 6% for sugar in most fruits. The K-FS200 has been evaluated in supermarkets, grading facilities, and wholesalers in Japan. The introduction of the K-FS200) has drawn attention to taste quality and its use is becoming more popular. In addition, researchers or farmers are becoming interested in measuring product ingredient not only after harvest but also during growing in the field so that they can make intelligent judgements concerning soil amendments, such as fertilizers and water, employs the fiber probe for flexible measurement and is battery powered for field use. Design of the fruit quality meters will be discussed. Applications to fruit quality will be presented.