• 유변학
• /
• 제11권1호
• /
• pp.57-65
• /
• 1999

분말사출재의 항복응력을 효과적이고 간단한 방법으로 측정하기 위해서 수차 장치를 사용한 항복응력 측정장치를 개발하였다. 수차 방식은 벽면 미끄러짐을 고려할 필요가 없는 장점이 있으나 전단률에 따른 점도 변화 측정에는 사용할 수 없는 단점도 있다. 수차 장치의 타당성 검토를 선형유체를 사용하여 검증하였으며, 수차 장치의 양단에서 나타나는 오차도 실험적으로 확인하였다. 분말 현탁액의 일반적인 특징이라고 여겨지는 항복 시 발생하는 순간 최대 토오크는 측정 장치의 제어기 특성에 따른 영향이 큰 것을 확인하고 안정 토오크 영역을 항복응력 계산의 기준으로 결정하였다. 측정되는 토오크에서 수차의 회전 저항에 따른 효과를 제거하기 위해 다양한 속도에서 측정된 토오크를 선형함수로 근사하여 회전 속도가 없을 때의 토오크를 얻었다. 측정 방법의 일반적인 검증을 위해 텅스텐 카바이드 분말과 왁스계 바인더를 이용한 분말사출재의 항복응력을 온도와 분말 충전률 변화에 따라서 측정하였다.

• 대한기계학회논문집
• /
• 제17권6호
• /
• pp.1465-1477
• /
• 1993

본 연구에서는 분말혼합체의 특성인 항복응력을 포함한 Generalized Newtonian Fluid의 구성 방정식을 도입하고 미끄럼현상을 고려한 신소재의 사출성형 충전과정 해석용 CAE(computer aided engineering)시스템을 개발하였다. 수치모사를 위한 수치해석방법으로는, 유한요소법(finite element method)과 유한차분법(finite difference method)을 함께 사용하였다. 유한요소법과 검사체적법(control volume technique) 을 병용하여 유동의 진행을 수치모사 하였으며, 유한차분법을 사용하여 온도분포를 계산하였다.

• 설비공학논문집
• /
• 제2권1호
• /
• pp.37-48
• /
• 1990

The drag and heat transfer reduction phenomena and degradation effects of drag reducing polymer solutions which are known as the viscoelastic fluids are investigated experimentally for the turbulent circular tube flows. Two stainless steel tubes are used for the experimental flow loops. Aqueous solutions of Polyacrylamide Separan AP-273 with concentrations from 300 to 1000 wppm are used as working fluids. Flow loops are set up to measure the friction factors and heat transfer coefficients of test tubes in the once-through system and the recirculating flow system. Test tubes are heated by power supply directly to apply constant heat flux boundary conditions on the wall. Capillary tube viscometer and falling ball viscometer are used to measure the viscous characteristics of fluids and the characteristic relaxation time of a fluid is determined by the Powell-Eyring model. The order of magnidude of the thermal entrance length of a drag reducing polymer solution is close to the order of magnitude of the laminar entrance length of Newtonian fluids. Dimensionless heat transfer coefficients of the viscoelastic non-Newtonian fluids may be represented as a function of flow behavior index n and newly defined viscoelastic Graetz number. As degradation continues viscosity and the characteristic relaxation time of the testing fluids decrease and heat transfer coefficients increase. The characteristic relaxation time is used to define the Weissenberg number and variations of friction factors and heat transfer coefficients due to degradation are presented in terms of the Weissenberg number.

• 대한기계학회논문집
• /
• 제13권5호
• /
• pp.1032-1043
• /
• 1989

본 연구에서는 해석적으로 열적 입구 길이를 규명하는데 필요한 와류 열확산 계수를 실험 결과를 이용하여 결정하고, 시험관 입구의 형상 변화가 열전달 특성에 미치는 영향을 실험적으로 결정하며, 열적 입구 길이 영역에서 국소 열전달 계수를 표시할 수 있는 실험식을 제시하고, 유체의 전단율에 따른 점성 계수의 실험 결과와 점탄성 유체의 특성시간을 이용한 새로운 무차원 수인 Weissenberg수를 결정하여 퇴화 현상을 분석하고저 한다.

• 방사성폐기물학회지
• /
• 제7권4호
• /
• pp.237-242
• /
• 2009

Pyroprocessing에 의한 사용후핵 연료 처 리 과정에서 핵 연료 물질은 전해정련장치, 전해환원장치, 전해제련장치의 전해조에서 전극표면에서의 전기화학반응과 전해질의 교반을 통해서 회수된다. 따라서 이 장치들은 장차 pyroprocessing의 실용화를 위하여 규모 확대가 필요하다. 본 연구에서는 교반을 수반하는 전해반응 장치를 대규모 장치로 확대코자 할 때 합리적으로 적용할 수 있는 장치규모 확대 기법을 고찰해 보았다. 장치 규모 확대에 있어 장치크기와 전극 표면적의 크기는 기하학적 유사성이 기본적으로 적용되어야 한다. 그밖에 전해질의 유동특성을 좌우하는 기준 가운데 전해질의 단위체적당 에너지 투입량이 동일하다는 기준을 채택할 경우 시행착오법 에 의한 계산절차를 도출해내었으며, 이 계산법은 전해조에서의 적절한 교반속도를 구할 수 있게 해 준다. 또 임의의 소규모 전해반응 시스템에 대하여 단위체적당 에너지 투입량이 동일하다는 기준과 교반기 날개끝 속도가 동일하다는 기준을 적용할 경우 전해조의 규모 확대에 관한 일례를 제시하였다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.45-50
• /
• 2001

This experimental study concerns the characteristics of a transitional flow in a concentric annulus with a diameter ratio of 0.52, whose outer cylinder is stationary and inner one rotating. The pressure losses and skin-friction coefficients have been measured for the fully developed flow of a 0.2 % aqueous solution of sodium carbomethyl cellulose (CMC) at a inner cylinder rotational speed of $0{\sim}600$ rpm. The transitional flow has been examined by the measurement of pressure losses, to reveal the relation of the Reynolds numbers with the skin-friction coefficients, in the laminar and transitional flow regimes. The occurrence of transition has been checked by the gradient change of pressure losses and skin-friction coefficient with respect to the Reynolds numbers. The increasing rate of skin-friction coefficient due to the rotation is uniform for laminar flow regime, whereas it is suddenly reduced for transitional flow regime and, then, it is gradually declined for turbulent flow regime. Consequently, the critical(axial-flow) Reynolds number decrease as the rotational speed increases. Thus, the rotation of inner cylinder promotes the early occurrence of transition due to the onset of taylor vortices.

• 센서학회지
• /
• 제17권4호
• /
• pp.289-294
• /
• 2008

The purpose of this study is to materialize the viscosity sensor by using the SH-SAW sensor of which the center frequency is operated at higher than 50 MHz. In order to measure the viscosity, SAW sensor of which the center frequency is operated at 100 MHz is developed. By using the developed sensor, phase shift, delay time, insertion loss, and frequency variation are measured at different viscosity. The result shows that the phase shift difference between the viscosity variations is such that the difference between the distilled water and the 100 % glycerol solution is approximately $45^{\circ}$, the change of the insertion loss is approximately 9 dB, and the difference of frequency variation is approximately 5.9 MHz. Therefore, it is shown that viscosity of unknown solution can be measured with the surface acoustic wave sensor.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.2095-2100
• /
• 2003

This Experimental study concerns the characteristics of vortex flow in a concentric annulus with a diameter ration of 0.52, whose outer cylinder is stationary and inner one is rotating. Pressure losses and skin-friction coefficients have been measured for fully developed flow of bentonite-water solution(5%) when the inner cylinder rotates at the speed $0{\sim}400rpm$. The results of present study reveal the relation of the bulk flow Reynolds number Re and Rossby number $R_o$ With respect to the skin friction coefficients. The effect of rotation on the skin friction coefficient is significantly dependent on the flow regime. In all flow regime, the skin friction coefficient is increased by the inner cylinder rotation. The critical (bulk flow) Reynolds number $Re_c$ decreases as the rotational speed increases. Thus, the rotation of the inner cylinder promotes the onset of transition due to the excitation of Taylor vortices.

• 한국미생물·생명공학회지
• /
• 제23권3호
• /
• pp.269-274
• /
• 1995

For the screening of a new functional exopolysaccharide, sugar composition and rheological properties of exopolysaccharide produced from Xanthomonas sp. EPS-1 were investigated. The average molecular weight of exopolysaccharide was determined to be approximately 2.l $\times$ 10$^{6}$ dalton. The new exopolysaccharide EPS-1 was composed of mannose, glucose, galactose and gluco- samine. IR analysis showed that the exopolysaccharide EPS-1 was assumed to be polymer with carbohydrates. NMR analysis showed that exopolysaccharide EPS-1 was presumed to be 4 units of sugar and trace of CH$_{3}$ group. Exopolysaccharide EPS-1 solution showed a characteristic of non-Newtonian fluid properties. At the concentration of 1.0%, the consistency index and the flow behavior index were shown at 10.8352 poise-sec and 0.4419, respectively. All dispersions were pseudoplastic fluids described accurately by Power-law model. Exopolysaccharide EPS-1 was highly viscous at low concentration, with good stability over a wide range of pH 5 to 13. The excellent compatibility of exopolysaccharide EPS-1 was represented with salts such as sodium chloride.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.747-752
• /
• 2003

Many clinical studies have suggested that the blood flow in ideal geometry is involved in the development of atherosclerosis. This study simulated blood flow in the abdominal artery with real geometry to investigate MWSS(mean wall shear stress), AWSS(amplitude of wall shear stress) and OSI(oscillator shear index). The calculation grid for the real geometry was constructed by extracting the surface of arterial wall from CT(Computed Tomography) or MRI(Magnetic Resonance Imaging) sheets called as DICOM (Digital Imaging and Communications in Medicines). The calculated MWSS, AWSS and OSI are much different from those of ideal geometry calculation. The MWSS increased while the AWSS decreased. Many shear forces are related to shapes of gradient. This paper will give clinical datum where the MWSS, AWSS and OSI are strong or weak. The hemodynamic analysis based on real geometry can provide surgeons with more reliable information about the effect of blood flow.