• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 추계학술대회 논문집
• /
• pp.131-139
• /
• 2005

It is very difficult to analyze the dynamic characteristic because tilting vehicle is a very complex system which are connected various mass element with tilting system. To realize and analyze actual phenomenon has restriction that usual commercial software calculates creep force under creep theory about wheel -rail contact mechanism as basic analyzing, and approach about contact point are based on two dimensional non-linear contact theory and simplified Hertzian contact which considers just displacement change on the YZ plain. Therefore, to solve these problems there should be a new approach difference with existing one. In this research, a new algorithm for finding wheel-rail contact position, calculation method of contact force and applied force will be presented.

• 한국생산제조학회지
• /
• 제22권6호
• /
• pp.913-920
• /
• 2013

This paper presents an applicable basic design that can configure non-contact levitation table for conveying a large sheet of glass. The suggested air levitation table consists of a series of air chambers with porous pads and fans as the conveyor system. The air supply chambers are arrayed to supply an adequately strong upward airflow for supporting the glass. Levitation is controlled by the size and discharge velocity, of the chamber arrays, as well as the glass supporting height. After pre-evaluation of the glass rigidity and the filer functional performance, a one-way fluid structure interface (FSI) analysis is performed for predicting pressure and deflection working of the 8G glass in the transverse and longitudinal directions, respectively. After comparing calculated levels of flatness of the glass, it determines the chamber array for the linear non-contact conveying motion.

• 연구논문집
• /
• 통권26호
• /
• pp.25-32
• /
• 1996

Water seals are used in a washing machine to seal rotating shafts and to prevent the penetration of dust, dirt or water from the outside. The design parameters of water seals, that were the location of the garter spring, the angle of the seal lip, and the interference, were investigated by the computer simulations using the hyperelastic non-linear large deformation finite element analysis code. The maximum contact stress and the distribution of stress on the seal lip were obtained for various type of water seals. The best type among the several investigated seals was selected considering the contact force and the sealing performance.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집
• /
• pp.1592-1597
• /
• 2009

Ratcheting is a cyclic accumulation of strain under a cyclic loading. It is a kind of mechanisms which generate cracks in rail steels. Though some experimental and numerical study has been performed, modeling of ratcheting is still a challenging problem. In this study, an elastic-plastic constitutive equation considering non-linear kinematic hardening and isotropic hardening was applied. Under the tangential stress of the contact stresses, a cyclic stress-strain relation was obtained by using the model. Strain under repeated cycles was accumulated.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2003년도 학술대회지
• /
• pp.335-340
• /
• 2003

This paper presents contact behavior of a perfluoroelastomer bonded door seal by a non-linear finite element method using the mechanical and thermal analysis. The shape effects are investigated for sealing performance of bonded door seal. Also maximum stress, temperature distribution and contact force are investigated. A bonded door seal was modeled three shape. The highest contact force occurs at model III(sunflower shape). The maximum stress of model III is lower than that of the others. The calculated FEM results show that the model III has excellent performance compared with other seal models.

• 한국해양공학회지
• /
• 제23권4호
• /
• pp.69-77
• /
• 2009

Structural analysis of a brake shoe for commercial vehicle was performed using finite element method. Since the strength of a brake shoe is affected by the magnitude and distribution shape of the contact pressure with the drum, the contact pressure between the shoe friction material and drum was calculated using a 2-Dimensional non-linear contact analysis in a state. And the brake was actuated by input air pressure and the drum of it was calculated both stationary and dynamic based on forced torque applied to the drum during the static state analysis. The results of the above analysis were then used as the load boundary conditions for a 3-Dimensional shoe model analysis to determine the maximum strain on the shoes. In the analysis model, the values of tensile test were used for the material properties of the brake shoes and drum, while the values of compression test were used for the friction material. We assumed it as linear variation, even though the properties of friction material were actually non-linear. The experiments were carried out under the same analysis conditions used for fatigue test and under the same brake system which equipped with a brake drum based on the actual axle state in a vehicle. The strains were measured at the same locations where the analysis was performed on the shoes. The obtained results of the experiment matched well with those from the analysis. Consequently, the model used in this study was able to determine the stress at the maximum air pressure at the braking system, thereby a modified shoe model in facilitating was satisfied with the required endurance strength in the vehicle.

• 한국산학기술학회논문지
• /
• 제19권8호
• /
• pp.14-18
• /
• 2018

일반적으로 반도체소자의 이동도를 높이기 위하여 반도체소자에서 옴접촉이 중요하게 다루어진다. 반도체 구조의 PN접합은 공핍층을 포함하고 있으며, 공핍층은 전기적인 비선형을 유도하고 쇼키접압을 만들어내는 반도체 고유의 물리적인 특징이다. 본 연구에서는 절연막이 전도성에 미치는 효과를 조사하기 위해서 $SiO_2$ 박막과 $V_2O_5/SiO_2$ 박막의 전기적인 특성을 비교하여 조사하였다. 미소전계영역에서 $SiO_2$ 절연막의 전기적인 특성으로부터 비선형 쇼키접합을 이루고 있는 것을 확인하였으며, 그 위에 증착된 $V_2O_5$ 박막은 오믹특성을 갖는 것을 확인하였다. 절연막의 PN 접합에 의한 쇼키접합 특성이 누설전류를 차단하여 $V_2O_5$ 박막의 전도성을 우수하게 만들었다. 양의 전압에서 $SiO_2$ 박막의 커패시턴스 값은 매우 낮았으나 $V_2O_5$ 박막의 커패시턴스 값은 전압이 증가할수록 증가하였다. 일반적인 전계영역에서 $SiO_2$ 박막의 절연 효과에 의해 $V_2O_5$ 박막의 전도성이 증가하는 것을 확인하였다. 절연박막은 공핍층의 효과를 이용하는 쇼키접합을 갖게 되며, 반도체에서의 쇼키접합은 전도성을 높이는 효과가 있는 것을 확인하였다.

• 한국공간구조학회지
• /
• 제13권1호
• /
• pp.8-16
• /
• 2013

• Structural Engineering and Mechanics
• /
• 제49권4호
• /
• pp.427-448
• /
• 2014

At present, the time of easy oil and gas is over. Now, the largest part of fossil fuels is concentrated in the deepest levels of tectonic structures and in the sea shelves. One of the most cumbersome operations of their extraction is the bore-hole drilling. In connection with austere tectonic and climate conditions, their drivage every so often is associated with great and diversified technological difficulties causing emergencies on frequent occasions. As a rule, they are linked with drill string accidents. A key role in prediction of these situations should play methods of theoretical modelling. For this reason, there is a growing need for development and implementation of new numerical methods for computer simulation of critical and post-critical behavior of drill strings (DSs). In this paper, the processes of non-linear deforming of a DS in cylindrical cavity of a deep bore-hole are considered. On the basis of the theory of curvilinear flexible rods, non-linear constitutive differential equations are deduced. The effects of the longitudinal non-uniform preloading, action of torque and interaction between the DS and the bore-hole surface are taken into account. Owing to the use of curvilinear coordinates in the constraining cylindrical surface and a specially chosen concomitant reference frame, it became possible to separate the desired variables and to reduce the total order of the equation system. To solve it, the method of continuation the solution by parameter and the transfer matrix technique are applied. As a result of the completed numerical analysis, the critical states of the DS loading in the cylindrical channels of inclined bore-holes are found. It is shown that the modes of the post-critical deforming of the DS are associated with its irregular spiral curving prevailing in the zone of bottom-hole-assembly. The possibility of invariant state generation during post-critical deforming is established, condition of its bifurcation is formulated. It is shown that infinite variety of loads can correspond to one geometrical configuration of the DS. They differ each from other by contact force functions.

• 한국정밀공학회지
• /
• 제27권7호
• /
• pp.109-116
• /
• 2010

The magnet wheel which generates on its interfacing conductive part a repulsive force and a traction torque by rotation of permanent magnets is used to manipulate the conductive plate without mechanical contact. Here, the air-gap magnetic field of the magnet wheel is shielded partially to convert the traction torque into a linear thrust force. Although a magnitude of the thrust force is constant under the fixed open region, we can change the direction of force by varying a position of the shield sheet. So, the spatial position of conductive plate is controlled by not the force magnitude from each magnet wheel but the open position of shield sheet. This paper discusses non-contact conveyance system of the conductive plate using electromagnetic forces from multiple magnet wheels.