• 제어로봇시스템학회논문지
• /
• 제4권3호
• /
• pp.406-412
• /
• 1998

This paper describes a contact position detection method of a capacitive touch screen panel. The proposed method is composed of a circuited compensating algorithm generating an output signal having phase difference to an input signal associated with contact position, converts both input and output signals into digital waveform (5V logic), and calculates the phase difference. Finally, position information with the phase difference is obtained by using a low-cost microprocessor, which is convenient to compensate non-linearity error. The proposed method, that computes phase difference directly, has advantages in feasibility and cost because it minimizes the use of analog devices; rather, it utilizes, cost effective digital circuit. Analytical results are also given.

• 전기학회논문지
• /
• 제58권10호
• /
• pp.2071-2078
• /
• 2009

In this paper, we proposed a non-contact respiration measurement system with ultrasonic proximity sensor. Ultrasonic proximity sensor approach of respiration measurement which respiration signatures and rates can be derived in real-time for long-term monitoring is presented. 240 kHz ultrasonic sensor has been applied for the proposed measurement system. The time of flight of sound wave between the transmitted signal and received signal have been used for a respiration measurement from abdominal area. Respiration rates measured with the ultrasonic proximity sensor were compared with those measured with standard techniques on 5 human subjects. Accurate measurement of respiration rate is shown from the 50 cm measurement distance. The data from the method comparison study is used to confirm the performance of the proposed measurement system. The current version of respiratory rate detection system using ultrasonic can successfully measure respiration rate. The proposed measurement method could be used for monitoring unconscious persons from a relatively close range, avoiding the need to apply electrodes or other sensors in the correct position and to wire the subject to the monitor. Monitoring respiration using ultrasonic sensor offers a promising possibility of non-contact measurement of respiration rates. Especially, this technology offers a potentially inexpensive implementation that could extend applications to consumer home-healthcare and mobile-healthcare products. Further advances in the sensor design, system design and signal processing can increase the range of the measurement and quality of the rate-finding for broadening the potential application areas of this technology.

• 한국지반공학회논문집
• /
• 제38권11호
• /
• pp.97-106
• /
• 2022

국내 매입말뚝 시공방법은 선굴착 후 최종단계의 항타 관입량으로 관리하는 것이 일반적이다. 관입량은 오래전부터 수기 측정방식에 의해 이루어지고 있으며, 작업자의 안전문제와 측정값의 신뢰도 부족 등에도 작업성의 한계와 비용 문제로 자동화 기술이 적용되지 않고 있다. 본 연구에서는 비접촉식 말뚝 관입량 측정 장치를 개발하고 기존 장치와 비교계측을 통해 현장 성능을 검증하였다. 또한 관입량 측정장치를 활용하여 현장 품질관리 방법에 대해 분석하였다. 실제 현장 실험을 통해 개발 장치를 활용한 관입량 측정과 수정 Hiley공식 및 동적감쇠계수 산정을 통해 보다 신뢰도 높은 지지력 추정이 가능한 것을 확인하였다. 연구결과에 따라 각 현장마다 수행된 동재하시험으로 부터 현장 보정 절차가 이루어지면 보다 신뢰성 높은 지지력 추정이 가능하며, 실제 현장에서는 동재하시험이 수행되지 않은 말뚝에 대해서도 지지력 관점의 말뚝 시공관리에 활용할 수 있을 것으로 판단된다.

• 한국정보통신학회논문지
• /
• 제26권9호
• /
• pp.1279-1292
• /
• 2022

신체적 불편함으로 인해 기존의 마우스와 같은 입력 장치의 사용이 힘든 사용자에게 도움이 될 수 있는 시스템으로 얼굴 인식과 Pyautogui 마우스 제어 기반의 비접촉식 입력 기법을 제안한다. 본 연구는 특히 화면 확대/축소나 스크롤 기능과 같이 웹 서핑을 보다 편리하게 돕는 기능이 포함되어 있으며, 개인의 신체적 차이 및 웹 사용 습관을 고려해 여러 설정값을 조정할 수 있도록 하였다. 또한, 기존의 시스템에서 한계점으로 제시되었던 눈 피로도에 대한 문제도 해결하였다. 추가로 고성능 CPU나 GPU 환경이 요구되지 않고 별도의 트래커 장치나 고성능 카메라 또한 필요하지 않다. 이러한 연구를 통해 손을 쓰기 어려운 장애인 및 노인들의 웹 접근성을 높여 배리어프리 실현에 기여하고자 한다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.1366-1370
• /
• 2007

Predicting the noise radiated from vibrating structures is important in the automotive, aerospace, construction equipment, and defense industries. In this paper, a numerical implementation of the boundary element method in solving the Helmholtz integral equation for radiated noise prediction is presented. To predict the noise emitted by vibrating structure, the developed code can use the results from a structure analysis performed by a multi-purpose structural finite element code like ANSYS and directly measured data by non-contact vibration sensor like Laser Doppler Vibrometer. To verify the accuracy of developed code, two kinds of verification are perfomed. Firstly, the computer code used the harmonic analysis results of ANSYS in simple model and try to match with SYSNOISE. After matching with simulation results, the code compared with the result from SYSNOISE which used the velocity data from the LDV measurement with different number of points. The performance of the developed code for vibro-acoustic noise prediction is presented using the experimental results of the non-contact sensor

• 대한전자공학회논문지SP
• /
• 제41권5호
• /
• pp.71-75
• /
• 2004

본 논문에서는 플라즈마 디스플레이 패널 생산 공정에서 카메라를 이용한 검사장비와 색차계를 이용한 검사장비 사이의 색차를 줄이기 위한 칼라 보정 방법을 제안한다. 칼라 보정 행렬은 두 장비에서 RGB 원색과 기준백색의 색도좌표로 획득한 RGB에서 XYZ 변환 행렬들 사이의 관계를 이용함으로써 구성할 수 있다. 제안한 칼라 보정 방법이 적용된 비접촉식 칼라 검사장비가 다양한 테스트 칼라에 대하여 영역 칼라 CCD 카메라에 의해 획득된 색도좌표를 색차계에 의해 측정된 색도좌표로 만족스럽게 보정됨을 실험결과에서 확인할 수 있다.

• 한국정밀공학회지
• /
• 제15권10호
• /
• pp.96-102
• /
• 1998

In this study, the theory and application of phase-shifting shadow moire topography is focused on the non-contact measurement of object surfaces for practical use in the field of production engineering. Shadow moire topography has been studied during last few decades in the area of the optical physics, and now its mathmatical theory has been established. Generally, in case of the classical shadow moire topography, the sensitivity is a few tenths of millimeter in best cases. Here we tried the application of phase-shifting method to the conventional shadow moire topography. But the reference grating and the deformed grating are mutually dependent because it is impossible to obtain uniform phase shifts on the whole Held. Therefore it is difficult to use a phase-shifting method in shadow moire topography. However, it was shown that constant phase-shifting was able to be measured by moving both the grating and light source. Finally we obtained a better result by using this procedure and applied the phase-shifting shadow moire to three dimensional object measurement.

• Steel and Composite Structures
• /
• 제42권2호
• /
• pp.151-159
• /
• 2022

This study discusses a hypothetical method for tracking the propagation damage of Carbon Reinforced Fiber Plastic (CRFP) components underneath vibration fatigue. The High Cycle Fatigue (HCF) behavior of composite materials was generally not as severe as this of admixture alloys. Each fissure initiation in metal alloys may quickly lead to the opposite. The HCF behavior of composite materials is usually an extended state of continuous degradation between resin and fibers. The increase is that any layer-to-layer contact conditions during delamination opening will cause a dynamic complex response, which may be non-linear and dependent on temperature. Usually resulted from major deformations, it could be properly surveyed by a non-contact investigation system. Here, this article discusses the scanning laser application of that vibrometer to track the propagation damage of CRFP components underneath fatigue vibration loading. Thus, the study purpose is to demonstrate that the investigation method can implement systematically a series of hypothetical means and dynamic characteristics. The application of the relaxation method based on numerical simulation in the Artificial Intelligence (AI) Evolved Bat (EB) strategy to reduce the dynamic response is proved by numerical simulation. Thermal imaging cameras are also measurement parts of the chain and provide information in qualitative about the temperature location of the evolution and hot spots of damage.

• 한국자동차공학회논문집
• /
• 제18권6호
• /
• pp.84-90
• /
• 2010

This paper presents the shape optimization process for the automotive wheel bearing seal lip using the finite element method and the response surface method. First, to predict performance of the bearing seal lip, we used the non-linear finite element analysis. And then, we compared the analysis results with the test results to verify the finite element model. The objective function in optimizing process was obtained from results of the mud slurry test, which is one of many tests for evaluating performance of wheel bearing. After the mud slurry test for the four models which have the similar cross-sectional shape, we measured the wear area of the seal lip and the moisture content in grease. The objective function has been chosen by comparing the results of mud slurry test and characteristics of seal lip, such as contact force, contact area, contact pressure, and interference. Finally, within limited design parameters, we suggested the optimized shape of seal lip, which is expected to improve the wear and the sealing effect of it.

• Steel and Composite Structures
• /
• 제4권6호
• /
• pp.489-507
• /
• 2004

The flexibility of the connection between steel and concrete largely influences the global behaviour of the composite beam. Therefore the way the connection is modelled is the key issue in its structural analysis. Here we present a new strain-based finite element formulation in which we consider non-linear material and contact models. The computational efficiency and accuracy of the formulation is proved with the comparison of our numerical results with the experimental results of Abdel Aziz (1986) obtained in a full-scale laboratory test. The shear connectors are assumed to follow a non-linear load-slip relationship proposed by Ollgaard et al. (1971). We introduce the notion of the generalized slip, which offers a better physical interpretation of the behaviour of the contact and gives an additional material slip parameter. An excellent agreement of experimental and numerical results is obtained, using only a few finite elements. This demonstrates that the present numerical approach is appropriate for the evaluation of behaviour of planar composite beams and perfect for practical calculations.