• 한국항공우주학회지
• /
• 제43권7호
• /
• pp.601-608
• /
• 2015

유연날개의 공력 및 구조 설계값을 설계 변수로 하여 정적 상태에서의 정적 공탄성해석 및 최적화를 수행하였다. 정적 공탄성해석과 최적화를 위해 상용 해석소프트웨어들이 연계된 강건한 다분야 최적설계 시스템을 개발하였다. 최적화 설계변수로는 가로세로비, 테이퍼비, 후퇴각과 날개 위아래 스킨 두께를 설정하였다. 전역적 다목적 최적화를 위해 실수기반 적응영역 다목적 유전자 알고리즘을 적용하였으며 계산시간을 줄이기 위해 메타모델로 서포트벡터회귀 기법을 적용하였다. 유연날개에 대한 파레토 결과 분석을 통해 최대 항속시간과 최소 중량에 대한 최적 결과를 확인하였다.

• Tribology and Lubricants
• /
• 제30권3호
• /
• pp.139-145
• /
• 2014

Nowadays, most micro-patterns are manufactured during flow line production. However, a conventional rotary chemical mechanical polishing (CMP) system has a limited throughput for the fabrication of large and flexible electronics. To overcome this problem, we propose a novel linear roll-CMP system for the planarization of large-area electronics. In this paper, we present a statistical analysis on the linear roll-CMP process of copper-clad laminate (CCL) to determine the impacts of process parameters on the material removal rate (MRR) and its non-uniformity (NU). In the linear roll-CMP process, process parameters such as the slurry flow rate, roll speed, table feed rate, and down force affect the MRR and NU. To determine the polishing characteristics of roll-CMP, we use Taguchi's orthogonal array L16 (44) for the experimental design and F-values obtained by the analysis of variance (ANOVA). We investigate the signal-to-noise (S/N) ratio to identify the prominent control parameters. The "higher is better" for the MRR and "lower is better" for the NU were selected for obtaining optimum CMP performance characteristics. The experimental and statistical results indicate that the down force and roll speed mainly affect the MRR and the down force and table feed rate determine the NU in the linear roll-CMP process. However, over 186.3 N of down force deteriorates the NU because of the bending of substrate. Roll speed has little relationship to the NU and the table feed rate does not impact on the MRR. This study provides information on the design parameter of roll-CMP machine and process optimization.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.968-971
• /
• 1996

In this paper, feedback controller is designed for ball-beam system using genetic algorithms. A genetic algorithms are implemented for optimizing gain parameters of feedback controller. We can find optimal point in multi-dimensional search space by using genetic algorithms. Performance of controller is tested by simulation of ball-beam system.

• ETRI Journal
• /
• 제24권3호
• /
• pp.251-254
• /
• 2002

We developed a method for optimal superframe design in the multi-frequency time division multiple access (MF-TDMA) return-link of a satellite multimedia interactive network called a digital video broadcasting return channel over satellite (DVB-RCS) sub-network. To find the optimal superframe pattern with the maximum data throughput, we formulated the design problem as a non-linear combinatorial optimization problem. We also devised the proposed simple method so that it would have field applicability for improving radio resource utilization in the MF-TDMA return link.

• Journal of applied mathematics & informatics
• /
• 제23권1_2호
• /
• pp.461-470
• /
• 2007

Parameter identification is studied in viscoelastic rods by solving an inverse problem numerically. The material properties of the rod, which appear in the constitutive relations, are recovered by optimizing an objective function constructed from reference strain data. The resulting inverse algorithm consists of an optimization algorithm coupled with a corresponding direct algorithm that computes the strain fields given a set of material properties. Numerical results are presented for two model inverse problems; (i)the effect of noise in the reference strain fields (ii) the effect of minimal reference data in space and/or time data.

• Journal of Electrical Engineering and Technology
• /
• 제6권1호
• /
• pp.59-66
• /
• 2011

This work treat the modeling and simulation of non-linear dynamic behavior of a web winding process during traction. We designate by a winding process any system applying the cycles of unwinding, transport, treatment, and winding to various flat products. This system knows several constraints, such as the thermal effects caused by the frictions, and the mechanical effects provoked by metal elongation, that generates dysfunctions due to the influence of the process conditions. Several controllers are considered, including Proportional-integral (PI) and Backstepping control. This paper presents the study of Backstepping controls strategy of the winding system. Our winding system is simulated in MATLAB SIMULINK environment, the results obtained illustrate the efficiency of the proposed control with no overshoot, and the rising time is improved with good disturbances rejections comparing with the classical control law.

• Structural Engineering and Mechanics
• /
• 제52권1호
• /
• pp.149-172
• /
• 2014

Four algorithms for damage detection of trusses are presented in this paper. These approaches can detect damage by using both complete and incomplete measurements. The suggested methods are based on the minimization of the difference between the measured and analytical static responses of structures. A non-linear constrained optimization problem is established to estimate the severity and location of damage. To reach the responses, the successive quadratic method is used. Based on the objective function, the stiffness matrix of the truss should be estimated and inverted in the optimization procedure. The differences of the proposed techniques are rooted in the strategy utilized for inverting the stiffness matrix of the damaged structure. Additionally, for separating the probable damaged members, a new formulation is proposed. This scheme is employed prior to the outset of the optimization process. Furthermore, a new tactic is presented to select the appropriate load pattern. To investigate the robustness and efficiency of the authors' method, several numerical tests are performed. Moreover, Monte Carlo simulation is carried out to assess the effect of noisy measurements on the estimated parameters.

• 대한조선학회논문집
• /
• 제42권6호
• /
• pp.654-665
• /
• 2005

In this paper, we present a non-linear integer programming by genetic algorithm (GA) for available sizes of stiffener or thickness of plate in a job site. GA can rapidly search for the approximate global optimum under complicated design environment such as ship. Meanwhile it can handle the optimization problem involving discrete design variable. However, there are many parameters have to be set for GA, which greatly affect the accuracy and calculation time of optimum solution. The setting process is hard for users, and there are no rules to decide these parameters. In order to overcome these demerits, the optimization for these parameters has been also conducted using GA itself. Also it is proved that the parameters are optimal values by the trial function. Finally, we applied this method to compass deck of ship where the vibration problem is frequently occurred to verify the validity and usefulness of nonlinear integer programming.

• 전기학회논문지
• /
• 제61권3호
• /
• pp.459-465
• /
• 2012

In this paper, we present a non-fragile guaranteed cost control design method for uncertain nonlinear systems with time varying delays in state and control input, even though the controller gain is perturbed. The uncertain nonlinear term in the systems is norm bounded and the linear matrix inequality(LMI) optimization method is employed as a stability analysis of the systems. We design a robust controller and show the asymptotical stability of uncertain time-varying systems based on Lyapunov method. Also, we guarantee a specific level of performance of the systems. The simulations are carried out to demonstrate the effectiveness of the proposed method.

• 대한기계학회논문집A
• /
• 제38권8호
• /
• pp.899-904
• /
• 2014

자유벌징에 있어서 성형 높이를 최대화하기 위하여 블랭크의 두께 분포를 최적화 하였으며, 등가정하중을 이용한 구조최적화법을 사용하였다. 두께형상은 부드러운 곡선으로 나타내기 위하여 베지어곡선을 사용하였고 제어점의 위치가 설계변수이며, 최대 변형률을 일정 값으로 제한하였다. 사용된 소재는 인코넬 718 이며 최적화된 두께분포로 가공된 블랭크를 이용한 자유벌징 시험을 수행하여 평판형 블랭크를 사용한 결과보다 22% 더 높은 성형 높이를 얻었다. 최적화결과에서 예측된 변형형상, 정점에서의 변형 경향, 두께분포가 실험에서 얻은 결과와 유사하여 최적화 과정의 유효성을 입증하였고, 최적화 결과가 실제 구현될 수 있음을 검증하였다.