• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.388-392
• /
• 2002

Fault tolerant control algorithm for heteropolar magnetic bearings are presented. This fault tolerant control utilizes grouping of currents as C-cores in order to isolate magnetic fluxes. Hardware requirements to maintain fault tolerant control are reduced since decoupling chokes are not required in this control scheme. The currents supplied to each pole are redistributed, if some coils fail suddenly, such that the resultant magnetic forces should remain invariant through coil failure events. Load capacity before magnetic saturation is reduced through coil failures while maintaining the same magnetic forces before and after failure.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 춘계학술대회 논문집
• /
• pp.392-393
• /
• 2014

Multilayer ceramic capacitors (MLCCs) have become one kind of the most widely used electrical components in recent decades. And the technology of MLCCs is developing continuously towards a direction of high capacitance and miniaturization. While the tiny thickness and the large quantity of the layers often make it very troublesome to do analysis with the full model MLCCs. In order to solve this problem, reduced model with fewer layers of MLCC was designed and verified in this paper.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 추계학술대회논문집; 한국과학기술회관; 6 Nov. 1997
• /
• pp.396-401
• /
• 1997

Dynamic stability of cylindrical shells subjected to follower forces is analyzed in this paper. Motion of shells is formulated in curvilinear coordinates that is consistent with assumptions made in the Timoshenko beam and the Mindlin plate. Using the finite element method, the induced equations are reduced to an equation with finite degrees of freedom. The 9-node Lagrangian element is used, and reduced integration is used to avoid shear and membrane locking. The effects of thickness ratio on the dynamic stability of cylindrical shells are studied.

• Journal of Biosystems Engineering
• /
• 제31권4호
• /
• pp.315-322
• /
• 2006

A torsional damper comprised of two stage pre-dampers was used to reduce the rattle noise generated in the PTO gear box of a direct engine-PTO driveline of agricultural tractors. It was designed and mounted to the engine flywheel to reduce the torque fluctuation-induced speed variations at the driving gears in the PTO gearbox, which were found to be main cause of the rattle noise. The effects of a hysteresis torque and a torsional stiffness of the damper on the speed variation were analyzed using an 11 degree of freedom non-linear model of the damped PTO driveline. The torsional damper was represented by a single degree of freedom model with 7 parameters. Under a constant hysteresis torque, velocity variation was reduced with decrease in the torsional stiffness of the damper. The velocity variation was also decreased with decrease in the hysteresis torque under a constant torsional stiffness. Optimum values of the torsional stiffness and hysteresis torque were obtained by the model simulation for the PTO driveline under the study. When the optimum values of the damper were used, the sound pressure level of the rattle noise was reduced by 81%, resulting in a reduction of 15dB(A). The optimum damper also reduced the engine speed variation, resulting in a reduction of 80% at the driving gears in the PTO gearbox. The torsional damper showed a good performance in reducing the rattle noise caused by the speed variation in the direct engine-PTO driveline.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 가을 학술발표회 논문집
• /
• pp.483-488
• /
• 2002

Noise has become an environmental pollution that affects most peoples' health, comfort or general well being. there are many sources of noise, but one of them clearly dominates road traffic noise. It has traditionally been associated with engine and exhaust noise of vehicles. However the emission and propagation of noise from these sources were partly reduced, while at the same time the noise emission from the tire/road interaction on a relative scale became more and more prominent Generally, Portland cement concrete(PCC) pavements have the advantage of durability and superior surface friction when compared to most dense-graded asphalt. However, It is known that PCC pavements create more noise than asphaltic surfaces due to the noise from interaction of tire and pavement surface. Therefore, recent research has shown some new concrete pavement textures to be worth further examination. So in this paper, we considered the 9 types of low noise concrete pavements to evaluate tire/pavement noise.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.849-854
• /
• 2001

Cabin noise reduction in maglev trains developed by KIMM is studied. Based on the measurements of cabin noise and acceleration levels during running and zero speed conditions, dominant noise sources are identified. After spectra characteristics of noise sources is investigated, efficient noise reducing methods are studied such as STL increasement of floor panels, sealing, and absorption treatment. It is found that the most important noise sources are VVVF inverter and SLIM in running condition. Since the noise sources are under the cabin floor, complete sealing and high STL of the floor panel are shown to be the most crucial factors in noise reduction. After polyurethan form (50t) is added for more sound absorption and sealing treatment, the cabin noise is reduced by 3-4 ㏈.

• 소음진동
• /
• 제10권5호
• /
• pp.806-810
• /
• 2000

This paper presents a practical method for reduction of interior noise and improvement of sound quality in compartment of passenger car. The tested vehicle has a booming noise problem at rear passenger seats. In order to identify the transfer path of interior noise, the running modal analysis, the vibro-acoustic frequency transfer response and the noise path analysis are systematically employed. Using these various methods, it has been founded that the rear part of the roof of the test car was a noise source for the booming noise. Through the modification of the roof, the booming noise has been reduced and sound quality inside car also has been improved.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 II
• /
• pp.647-652
• /
• 2001

A noise reduction of noise barrier for high speed train was measured by using scale down model test. A selected types of noise barriers were simple vertical barrier, interference type barrier with plate, interference type barrier with cylindrical pipes. On experiment, in order to make similar present test lane condition, reduced train model and multiple noise sources were considered. As a result. interference type noise barrier with cylindrical pipes is most effective than other barriers. A present height of noise barrier which is established in a test lane is not high enough for reducing patograph noise.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.204-209
• /
• 2004

Recently, the various performances of vehicle are rapidly improved. Therefore tire noise is recognized as important noise source because vehicle noise is considerably reduced. This study is performed for the control of the cavity resonance noise that is structure-borne noise, due to fluid(air)-structure interaction. For this investigation, FRF analysis has been carried out using FEM and we found an important factor affecting cavity resonance. The effect of this factor is confirmed by objective noise test. We confirmed that the result of FRF analysis and objective noise test is that the structure control of tire sidewall can reduce cavity resonance noise due to fluid-structure interaction

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2010년도 추계학술대회 논문집
• /
• pp.362-367
• /
• 2010

This paper deals with the correlation between the interior noise and the floor vibration of the train from rolling, impulse and friction in Busan Metro line 3. The correlation is verified by sound and vibration measurement causing friction between the railway and the wheel. If ANC(Active Noise Control) system can reduce 5 dB in below 500 Hz, the sound pressure level of the whole band pass can be reduced about 1.8-4.8 dB in squeal noise. Curve squeal noise is the intense high frequency tonal that can occur when a railway vehicle transverses a curve. The frequency range is from around 500 to almost 20,000 Hz, with noise levels up to about 15 dB in curve.