• 한국소음진동공학회논문집
• /
• 제17권3호
• /
• pp.249-256
• /
• 2007

Aircraft noise is a serious problem to inhabitants near airports. INM is one of programs for determining the predicted noise impact in the vicinity of airports. It has been widely used for engineers to evaluate aircraft noise. However it is difficult to predict aircraft noise in case of lack of exact INM input data. The exact informations about a fighter plane are not known well for a security problem. This study presents methods of reducing errors between measurement and simulation when the exact INM input data is not known. Especially we adjusted the thrust force of aircraft engine and reduced the error.

• 소음진동
• /
• 제4권2호
• /
• pp.231-238
• /
• 1994

This paper presents an experimental method to find the vibrational transmission characteristics of structures by using the structural intensity method which is used as the important techniques of active vibration control method. Experimental results are obtained from measurements performed on a structure beam by 2, 3 and 4 position linear accelerometr array (2, 3 and 4 structural intensity : 2, 3 and 4 S.I.) methods at near and farfield conditions. These results are compared with the measurement values of conventional power flow measurement method called input power measurement in order to verify the accuracy of structural intensity methods. To minimize the errors associated with 2, 3 and 4 S.I. methods, the measurement locations were selected by the result of modal analysis and the averaged data by the inter-change of accelerometer array was utilized. In 3 and 4 S.I. methods measured wavenumber instead of theoretical wavenumber was used. This paper shows that measurements of bending wave power flow by using 2, 3 and 4 S.I. methods can give accurate values under general field conditions in structural beam and the accuracy of 2, 3 S.I. methods is higher than 4 S.I. methods. Finally, 2 position linear accelerometer array method is suggested as the practical structural intensity technique.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.286-289
• /
• 2008

Damping materials are widely used to reduce vibration or noise generation of structures. To understand their damping capability and for use in numerical simulations, their viscoelastic properties should be measured in the frequency range of interest. In this study, experimental setup is proposed to measure materials properties of very compliant polymer materials. The polymer materials used in this study are difficult to form into rod shapes, and typical resonance methods are not applicable. In the proposed measurement setup, the damping materials were modeled as a simple viscoelastic support at one end of the beam. Their properties were measured through analysis of their effects on the wave propagation characteristics of the beam structure.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.340.1-340
• /
• 2002

The unbalance exciting force induced by HDD of lately getting higher speed is directly influenced by the rotational speed and the mechanical assembly allowance between disk and spindle motor, and which gives rise to the structure borne noise of the personal computer. The absolute unbalance mass of HDD needs to be measured and adjusted by the counter mass to control the unbalance exciting force effectively in the stage of assembling the disk and spindle motor. This study introduces the measurement methods of the magnitude of the absolute unbalance mass and the position of HDD by 2 accelerometers. The absolute unbalance mass can be obtained by the acceleration responses and the mobility of the mechanical part, while the position of the unbalance mass can e obtained by the rotation acceleration orbit.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 I
• /
• pp.517-521
• /
• 2001

Measurement techniques for the in-duct source characteristics of fluid machines can be classified into direct method and load method, according to whether the technique employs an external acoustic source or not. It has been known that the two methods yield different results and the load method used to come up with a negative source resistance, in spite of the fact that a very accurate prediction of radiated noise can be obtained by using any result. This paper is focused to the effect of time-varying nature of fluid machines on the output result. For this purpose, a simplified fluid machine consisting of a reservoir, a valve and a pipe is considered as representing a typical linear, periodic, time-varying system and the measurement techniques are simulated by utilizing the Hill equation and its steady-state forced response. In the load method, the source impedance turns out being dependent on the valve impedance at the calculation frequency and the valve and load impedances at other frequencies as well.

• 한국소음진동공학회논문집
• /
• 제19권9호
• /
• pp.943-949
• /
• 2009

Many studies for measuring vibration using image signal are suggested. These methods can measure vibration of multi-points simultaneously. However, it has the disadvantage that is very sensitive to an environment. If the measured environment is not good, image signals can be measured including much background noise. So, it is difficult to obtain accurate vibration from the measured image signals. Another problem is that camera imaging has a resolution limit. Because the resolution of the camera image is relatively much lower than that of a data acquisition system, accurate measuring vibration cannot be performed. In this paper, we proposed the enhanced technique for measuring vibration using camera signal. The key word of this paper is a curve fitting. The curve fitting can exactly detect the measurement line of interested object. So, we can measure the vibration in noisy environment. Also, it can overcome the resolution limit.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.281-285
• /
• 2002

A new method of dynamic contact force measurement between a pantograph and a contact wire is proposed in this paper The method does not require design modification of an original pantograph in order to install sensors such as load cells. Contact forces can be expressed as the sum of vertical shear forces at the support points and inertial forces. Using specially-designed strain gage rosettes. vertical shear forces at the supported points can be measured without noise mixing and thermal effects. In order to obtain contact forces from shear forces, 3 inertial force compansation methods are proposed and compared in this paper. By validation process, the new proposed measurement method is verified to be applicable to the on-line current collection test.

• 한국도로학회논문집
• /
• 제15권6호
• /
• pp.33-39
• /
• 2013

PURPOSES : This research investigates traffic noise characteristics as change the transverse rumble strips shape from rectangular to cylinder at toll plaza of highway. METHODS : The traffic noise was investigated at two different places at toll plaza of highway. One is modified grooving, another is employed cylinder shape of TRS instead of rectangular shape of TRS. A measurement of traffic noise was conducted at same location and time period. The traffic volume information was gotten from office of highway office and vehicle speed was measured by speed measuring device. The traffic noise measurement was conducted from 13:00 to 23:00 and by pass-by method. Also, the traffic noise was measured behind noise barrier. Various distance from noise barrier(7.5m, 30m, 50m) and different heights(1.2m, 3m, and 5m) were parameter for measurement of traffic noise in this study. RESULTS : The class 1 vehicle was contributed from traffic volume which was increased 1,500. However, the distribution of traffic speed didn't change compare to previous investigated period. From this study, It was found that the external traffic noise was changed as function of geometric shape of TRS. The external noise from modified grooving was less than 1.2dB(A) of the current TRS. A difference of traffic noise was 20dB(A) before and after barrier. It came from a noise barrier effect as reduction of traffic noise. According to investigate a traffic noise distribution near barrier, there is similar noise characteristic as function of height at 7.5m distance from noise barrier. Also, There is no different traffic noise between 30m and 50m from source of the noise of sound barrier. CONCLUSIONS : Based on this traffic noise investigation result, there is a clear characteristic difference as changed TRS shape. The traffic noise was reduced by changed TRS shape. Specially, traffic noise was decreased although the traffic volume was increase for same investigation time and period. It is implied that cylinder type of TRS significantly reduces the traffic noise. The specification of various TRS will be studied in the future.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.119-124
• /
• 2000

This paper introduces the brief guidelines on general aspects of tests and experiments with human subjects. Detailed methods for measuring whole-body vibration are reviewed for those tests and experiments and compared each other. Such comparison is found to be very useful in choosing adequate methods for human related tests and experiments. Of course, it is also expected to be very meaningful to our automotive research and industrial fields that are critical to the ride quality of their products with uncomfortable acoustic noise and vibration.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계 학술대회논문집(수송기계편)
• /
• pp.53-56
• /
• 2005

Aircraft noise is a important problem to inhabitants near airports. INM is one of programs for determining the predicted noise impact in the vicinity of airports. It has been widely using for engineers to evaluate aircraft noise. However it is difficult to predict aircraft noise in case of lack of exact INM input data. The exact informations about a fighter plane are not known well for a security problem. This study presents methods of reducing errors between measurement and simulation when the exact INM input data is not known. Especially we adjusted the thrust force of aircraft engine and reduced the error.