• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 II
• /
• pp.1215-1220
• /
• 2001

Wind tunnel test of a new pantograph, that is developed through the KHST project, was performed in RTRI wind tunnel test center of Japan end of last June. This paper indtroduces the measurement results and analysis of noise measurement part that is achieved during the wind tunnel test. The maximum measured sound pressure level at 5m shows 102.3dB(A) at 350km/h and it leads to 88.3dB(A) of predicted sound pressure at 25m that satisfy 91dB(A) of evaluation criteria. Major noise sources of the pantograph was identified as a link between upper and lower arm, panhead contact strips and shunt wires.

• 한국소음진동공학회논문집
• /
• 제18권4호
• /
• pp.400-410
• /
• 2008

Reduction of structure-borne noise in the compartment of a car is an important task in automotive engineering. Many methods which analyze noise transfer path have been generally used for structure-borne noise. These methods are useful in solving particular problem but do not quantify the effectiveness of vibration isolation for each isolator of a vehicle. To quantify the effectiveness of vibration isolation, the vibrational power flow measurement has been used for a simple isolation system or a laboratory based isolation system. This paper identifies the transfer path of booming noise in a SUV. The powertrain used for test has a in-line 4cylinder engine and 5-shift auto-transmission. This powertrain is transversely supported by four isolators. We calculated the energy flow throughout four isolator by the measurement of power flow and the contribution of energy flow at each isolator.

• 한국안전학회지
• /
• 제31권2호
• /
• pp.90-97
• /
• 2016

The objective of this study is to evaluate the operator's safety for the risk assessment method of impulsive noise division. Literature reviews on the basis of the impulsive noise study, the measuring methods and procedures, based on the results of the analysis process presents a risk assessment methods. In this study, analysis of the MIL-STD-1474D, B-duration graph for the peak noise level to cross the line from the measurement results is limited by the risk retracted. It is possible to determine whether there is quick can be determined whether the risk. Measurement positions measured by the microphone is installed on the risk of applying results are so located within the tolerance impulsive noise in the measurement position can interpret subjective safety is ensured. In addition, Proportional Dose technology was the proposed by the Patterson with the risk assessment method was applied to the indoor-impulsive noise. As results of this study, results for the same value of applying the technique of Proportional Dose technology results calculated by MIL-STD-1474D methods allows 1 count once increased in comparison to the result obtained.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.1067-1071
• /
• 2004

In this paper, the characteristic of the regenerative pump is reviewed by the measurement and the analysis. The dominant noise sources are harmonic components of the rotating impeller frequency. The acoustic characteristics and the noise source position at the dump are identified. In order to reduce the high-level peak noise, the interior flow of the pump chamber is analyzed by CFD (Computational Fluid Dynamics). Acoustic pressure is calculated with Ffowscs Williams and Hawkings equation. As the result of the analysis new design of the pump chamber is recommended. The recommended pump is compared with original pump by evaluating the RMS value of a interior static pressure and the sound pressure level. The new pump chamber recommended by analysis results is proved by a process of the measurement. The overall SPL of a recommended pump is reduced about 3 dBA.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권4호
• /
• pp.396-402
• /
• 2014

함정의 높은 함내소음은 승조원들 간의 의사전달을 방해하여 전투력 저하를 야기하고, 근무환경의 질을 떨어뜨리므로 함내소음 측정은 매우 중요한 관리 항목 중 하나이다. 그러므로 대부분의 신조함정은 인수 시운전 단계에서 함내소음을 측정하고 제시된 기준을 만족하도록 건조되고 있다. 함내소음 측정 결과로부터 기준 만족 여부를 판단하기 위해서는 측정 불확도를 고려하는 것이 반드시 필요하다. 본 논문에서는 함정 인수 시운전시의 함내소음 평가 방법을 소개하고, 함내소음을 평가하기 위한 불확도 추정 방법을 적용하였다. 신조 함정 7척에 적용한 결과, 함내 소음 불확도는 1dB 이하로 오차가 시운전 평가서 허용 오차(2dB) 내에 있음을 확인하였다. 현재 실험방법은 허용기준을 만족하고는 있지만 보다 신뢰성 있는 측정 결과를 위해 실험 방법 등의 개선으로 허용오차를 줄일 필요성이 있을 것으로 판단된다.

• 한국소음진동공학회논문집
• /
• 제15권5호
• /
• pp.550-557
• /
• 2005

Korean 'Law of Aviation' and 'Test Method of Measuring Noise and Vibration' designate to use WECPNL metric based on $L_{max}$ measurement for the accessment of aircraft noise in Korea. However, time duration of noise event can not be considered in $L_{max}$ metric in principle, compensation on the duration has been utilized. A study was done recently to evaluate appropriate duration compensation for the accessment of military aircraft noise under current metric of WECPNL and $L_{max}$. This study was carried out to evaluate what metric is the most appropriate to express aircraft noise including time duration of single noise event, computing and comparing noise exposure with 1 second noise measurement data of military aircraft in $L_{max}$, $L_{Aeq,\;T}$ and SEL. This study shows SEL is the most appropriate noise metric for the evaluation of noise exposure with time duration such as aircraft noise without compensation. It is suggested to use SEL noise metric instead of $L_{max}$ noise metric with duration compensation for the aircraft noise accessment either military aircraft or civilian aircraft.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.580-586
• /
• 2005

In this study, experimental tests for driving noise of various optical disk drives (ODD) have been performed using 1/2' microphone noise measurement system. Several new and old ODD models by different manufacturers are practically considered and compared far realistic driving conditions. Sound insulation case with absorbing material fur the present experimental tests is designed and constructed using CATIA system. It is found that average data transfer rate, operating RPM, and sound noise level seems to be different for the same opposed speed ODD by different manufacturers. Moreover, driving sound noise level can be largely affected by both tray shape and driving speed even for the same apparent data transfer rate.

• 한국소음진동공학회논문집
• /
• 제15권10호
• /
• pp.1169-1176
• /
• 2005

In this study, experimental tests for driving noise of various optical disk drives (ODD) have been performed using 1/2' microphone noise measurement system. Several new and old ODD models by different manufacturers are practically considered and compared for realistic driving conditions. Sound insulation case with absorbing material for the present experimental tests is designed and constructed using CATIA system. It is found that average data transfer rate, operating RPM, and sound noise level seem to be different for the ODD models with same denoted speed by different manufacturers. Moreover, driving sound noise level can be largely affected by both tray shape and driving speed even for the condition of the same apparent data transfer rate.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.271-274
• /
• 2005

For noise and vibration order-analysis on rotating machinery, it is compulsory to measure the RPM of the rotating part of the machine. Normally the RPM is measured using dedicated tacho-probes. In this paper we describe a new method that in real-time synthesizes a tacho signal from the measured noise or vibration signal thus eliminating the tacho probe. The method strengths and weaknesses are evaluated on practical signals.

• 한국음향학회지
• /
• 제42권2호
• /
• pp.124-132
• /
• 2023

건축물이 고층화될수록 승강기와 인접한 세대 수가 증가하고 그에 따라 승강기 사용 횟수도 증가할 것이다. 그에 따라 승강기 소음은 앞으로 증가할 수밖에 없다. 하지만 현재 우리나라는 승강기 소음에 대한 법적 기준이나 승강기 소음을 명확히 측정할 수 있는 측정 및 평가 방법 또한 마련되어 있지 않다. KS F ISO 16032에 승강기 소음 측정 방법이 일부 제시되어 있지만, 이 표준은 승강기 소음을 대상으로 제정된 규격이 아니다. 건축 설비 기기의 전반적인 측정 방법을 통합하는 성격의 표준으로 측정 시 마이크로폰 위치를 실험자가 선정 하도록 되어있다. 승강기 소음은 중저주파수대역이 중요한 소음으로 음압레벨이 낮은 것이 특징이다. 하지만 현재까지도 승강기 소음에 대한 거주자의 불만은 증가하고 있다. 이 연구에서는 승강기 소음 측정 시 승강기 소음을 가장 민감하게 수음할 수 있는 마이크로폰의 위치에 대해 연구하였다. 벽면에서부터의 이격거리와 바닥으로부터의 높이에 따라 총 9개의 마이크로폰 위치에 대해 측정 하고, 분석하였다. 실험 결과 승강기 소음은 63 Hz 대역에서 영향력이 매우 높은 소음임을 확인하였다. 중앙점에서의 측정값은 전체 승강기 소음 레벨 값을 낮추는 요인으로 확인되었다.