• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2001년도 종합학술발표회 논문집 Vol.11 No.1
• /
• pp.222-226
• /
• 2001

In this paper, 2.4GHz RF Module using Even Harmonic Mixer(EHM) was designed and fabricated for Direct conversion(DC) system. By minimizing performance degradation of DC system with DC offset and LO radiation, the capability of minimization and one chip solution in wireless system was proposed. The designed EHM using anti-parallel diode pair represented 9dB conversion loss and about -60dBm 2LO leakage radiation in RF port, and output reflection and reverse transmission characteristic of low noise amplifier was improved. So superior DC offset suppression characteristic is expected. RF Module which consists of EHM, LNA, RF amplifier, Frequency synthesizer and Duplexer was designed and fabricated.

• Journal of Electrical Engineering and Technology
• /
• 제9권1호
• /
• pp.136-142
• /
• 2014

A major problem in Switched Reluctance Motor (SRM) is torque ripple, which causes undesirable acoustic noise and vibration. This work focuses on reducing the undesirable torque ripple in SRM by modifying stator and rotor geometry. This paper presents a comparative study on torque ripple minimization in SRM with modified pole shapes such as stator pole taper, stator pole face with non-uniform air gap and pole shoe attached to rotor pole. Further this paper presents a detailed sensitivity analysis of the effect of different geometrical parameters that alter the pole face shapes on the performance of SRM. The analysis is performed using finite-element method considering average torque and torque ripple as performance parameters. Based on the analysis, a design combining stator pole taper with non-uniform air gap is proposed to improve the torque characteristics of SRM. The dynamic characteristics of the proposed design are simulated and the results show satisfactory reduction in torque ripple.

• Smart Structures and Systems
• /
• 제8권2호
• /
• pp.191-204
• /
• 2011

A technique for damage localization and assessment based on measurements of both eigenvectors curvatures and eigenfrequencies is proposed. The procedure is based on two successive steps: a model independent localization, based on changes of modal curvatures, and the solution of a one-dimensional minimization problem to evaluate damage intensity. The observability properties of damage parameters is discussed and, accordingly, a suitable change of coordinates is introduced. The proposed technique is illustrated with reference to a cantilever Euler beam endowed with a set of piezoelectric transducers. To assess the robustness of the algorithm, a parametric study of the identification errors with respect to the number of transducers and to the number of considered modal quantities is carried out with both clean and noise-corrupted data.

• 전력전자학회논문지
• /
• 제7권1호
• /
• pp.91-100
• /
• 2002

본 논문에서는 매입형 영구자석 동기전동기의 전자기 토크의 맥동저감에 관하여 기술하였다. 일반적으로 토크 맥동은 전동기의 진동과 소음을 유발하는 중요한 원인이 된다. 제안된 방법에서는 비정현적인 역기전력을 가진 IPMSM에서 토크 맥동을 저감하기 위해 단위전류당 최대토크 제어를 할 수 있는 최적의 전류 형상을 고려하여 도출하였다. 그리고 이를 전동기에 인가했을 때 토크 맥동이 개선될 수 있음을 시뮬레이션과 실험을 통해서 입증하였다.

• 한국통신학회논문지
• /
• 제27권3A호
• /
• pp.240-248
• /
• 2002

본 논문에서는 연속영상에서 움직이는 객체의 motion에 기반하여 영상을 분할하는 새로운 알고리즘을 제안하였다. 전체적인 분할 과정은 2단계로 구성되어진다. 첫 단계는 '픽셀 레이블링' 단계이며, 두 번째 단계는 'motion 분할' 단계이다. '픽셀 레이블링' 단계에서는 optical flow에 의해 발생하는 속도 벡터들의 크기에 따라 영상의 각 픽셀에 레이블을 부여한다. 'Motion 분할' 단계에서는 첫 단계에서 생겨난 불필요한 잡음을 제거하기 위해 motion 필드를 마코프 랜덤 필드로 모델링하여 에너지 최소화를 통해 motion을 분할한다. 실험결과, 제안된 알고리즘이 연속영상에서 움직이는 객체의 motion을 효율적으로 분할함을 확인할 수 있었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.942-944
• /
• 2003

Detent force produced in permanent linear machines generally causes an undesired effect that contributes to the output ripple of machine, vibration and noise. This paper analyzes detent force and thrust in Permanent Magnet Linear Synchronous Motor(PMLSM) by using various detent force minimization techniques. A two dimensional Finite Element Analysis(FEA) is used to Predict detent force and thrust due to structural factors and non-linearity.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 전력전자학술대회 논문집
• /
• pp.142-145
• /
• 2001

In this paper the electromagnetic torque developed in IPMSM(Interior Permanent Magnet Synchronous Motor) is analyzed. If flux distributions in the motor are not sinusoidal, a sinusoidal current produces important torque ripple. Torque ripple causes vibration and noise of motors. The optimized current waveforms for ripple free is able to be obtained by analysis of Back-EMF and torque equation. The method to find the optimal current is based on numerical predetermination. In this paper proposes current waveform which can eliminate the torque ripple, and the validity is verified through the simulation.

• Tribology and Lubricants
• /
• 제20권3호
• /
• pp.157-162
• /
• 2004

The cam curve of a balance type vane pump consists usually of circular arcs and Archimedes' spirals. However, if they are connected directly together, the curve must have a few discontinuous points of the gradients and the motion of the vanes is no longer smooth. Designing data for an oil hydraulic vane pump used in power steering system were obtained by the acquisition of optimum cam profile data which can be available to reduce noises and vibrations through the minimization of cavitation with the improvement of suctional performance. The performance test is carried on the trial manufactures by measuring the volumetric and the mechanical efficiency. And from that result, maintaining the same characteristic as the conventional one in the relief pressure and noise level, the experimental pump discharges 0.7 $\ell$/min and shows nearly 3.5% enhancement in the total efficiency more than the conventional one.

• 소음진동
• /
• 제2권4호
• /
• pp.273-280
• /
• 1992

The prediction of vibration response of floor is necessary in order to check whether the floor vibration level will satisfy the allowable vibration standard of precise machinery such as electronic microscopes in semiconductor manufacturing plant before the installation of various neighboring equipment facility. In conventional vibration isolation, we were mainly interested in minimization of vibration transmissibility and stabilization of vibration isolation system. But in order to predict vibration response of floor, it is necessary to know exciting force of equipment installed on the floor and the mobility of the floor. We measured the exciting force of the dropped mass assumed as equipment and the mobility of some practical building floor using large impact hammer. And from this we predicted the vibration response of floor on which the mass dropped. This predicted vibration response of floor is compared with measured vibration response. Through upper procedure, we examined the possibility of predicting vibration response of floor from the information of exciting force of equipment and the mobility of floor.

• Structural Engineering and Mechanics
• /
• 제70권6호
• /
• pp.649-659
• /
• 2019

Vibration-based structural damage detection through optimization algorithms and minimization of objective function has recently become an interesting research topic. Application of various objective functions as well as optimization algorithms may affect damage diagnosis quality. This paper proposes a new damage identification method using Moth-Flame Optimization (MFO). MFO is a nature-inspired algorithm based on moth's ability to navigate in dark. Objective function consists of a term with modal assurance criterion flexibility and natural frequency. To show the performance of the said method, two numerical examples including truss and shear frame have been studied. Furthermore, Los Alamos National Laboratory test structure was used for validation purposes. Finite element model for both experimental and numerical examples was created by MATLAB software to extract modal properties of the structure. Mode shapes and natural frequencies were contaminated with noise in above mentioned numerical examples. In the meantime, one of the classical optimization algorithms called particle swarm optimization was compared with MFO. In short, results obtained from numerical and experimental examples showed that the presented method is efficient in damage identification.