• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.650-651
• /
• 2008

In this thesis, source identification tool for NI-PXI equipment is developed with LabVEIW. For the purpose of examining propriety of developed tool, simulation is performed with several signals that have different frequency range. After checking the coherence functions for concerned frequency domain, an experiment is conducted on an evaporator that cause the principal noise of a refrigerator.

• 한국소음진동공학회논문집
• /
• 제25권11호
• /
• pp.723-730
• /
• 2015

This paper investigated the noise generation mechanism of a rotary compressor using experimental method. The measurement was carried out for primary parameters which influence noise characteristics. By using STFT(short time Fourier transform), noise sources of a rotary compressor were identified and vibrating modes that increase the noise are verified. Also, it was studied that the correlation between operating speed and noise. Main factors that affect the variation of noise level were considered by the comparison of the experimental results. In addition, a dynamic characteristic of crank shaft was studied and the critical speed was analyzed.

• 한국소음진동공학회논문집
• /
• 제14권10호
• /
• pp.930-938
• /
• 2004

This paper presents the noise source identification of a car A/V system. There are two different kinds of noise sources noise generated by loading mechanism and rattle noise by externally forced vibration. A dynamometer has been made to produce stationary inertia to the loading mechanism of A/V system. Sound pressure spectra and sound intensity were measured by operating the dynamometer setup as various motor speeds, and the results were analyzed. A dominant rattle noise source about A/V system's components has been found by multi-dimensional spectral analysis. Residual spectrum method was applied for eliminating coherence between the vibration sources. In result, the dominant rattle noise source was identified by partial coherent output spectrum of individual vibration component.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.753-759
• /
• 2014

In this paper, it is investigated that noise generation mechanism of a rotary compressor using experimental method. The measurement was carried out for primary parameters which influence noise characteristics. By using STFT(short time fourier transform), noise sources of a rotary compressor were identified and vibrating modes that increase the noise are verified. Also, it was studied that the correlation between operating speed and noise. Main factors that affect the variation of noise level were considered by the comparison of the experimental results. In addition, a dynamic characteristic of crank shaft was studied and the critical speed was analyzed.

• 한국소음진동공학회논문집
• /
• 제21권9호
• /
• pp.787-797
• /
• 2011

The noise in a vehicle is an important factor for customers purchasing a car. Particularly, reduction of the noise that is generated from HVAC(heating, ventilation and air conditioning) is very important since it has considerable effects on interior noise. In general, identification of noise source is crucial to reduce noise level. The complex acoustic intensity method is widely used to obtain the accurate measurement and identification of noise source. Therefore, in the previous study, noise source of HVAC was identified through experimental approach using the complex acoustic intensity method. In this study, we are intended to confirm reduced level of noise by comparing the result between before and after modification of cam curve that is based on identified noise source of HVAC. It is found out that noise source of HVAC are motor and cam area using the complex acoustic intensity method in the previous study. We performed experiments to compare noise level between before and after modification of cam curve. Especially, it can be seen that complex acoustic intensity method using both active and reactive intensity is vital in devising a strategy for comparison to noise level. Also, the vector flow of acoustic intensity was investigated to identify sound intensity distributions and energy flow in the near field of HVAC.

• Structural Monitoring and Maintenance
• /
• 제3권4호
• /
• pp.395-406
• /
• 2016

Modal parameter identification has received much attention recently for their usefulness in earthquake engineering, damage detection and structural health monitoring. The identification method based on Matrix Pencil technique is adopted in this paper to identify structural modal parameters, such as natural frequencies, damping ratios and modal shapes using impulse vibration responses. This method can also be applied to dynamic responses induced by stationary and white-noise inputs since the auto- and cross-correlation function of the two outputs has the same form as the impulse response dynamic functions. Matrix Pencil method is very robust to noise contained in the measurement data. It has a lower variance of estimates of the parameters of interest than the Polynomial Method, and is also computationally more efficient. The numerical simulation results show that this technique can identify modal parameters accurately even if the noise level is high.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.676-681
• /
• 2002

System Identification is carried out for a full scale five-story builing to design a vibration controller. Dynamic characteristics such as natural frequencies, damping ratios, and modes are obtained from the input/output information by both sine-sweep method and white noise method. The active mass driver installed on the five floor is applied as external loading to move the building and each floor acceleration is measured and processed for the system identification. The identified building will be experimentally investigated again with viscoelastic dampers installed at inter-stories to obtain the response behavior. Corresponding result will be presented soon.

• 한국소음진동공학회논문집
• /
• 제18권4호
• /
• pp.458-464
• /
• 2008

The structural health monitoring has been gaining more importance in civil engineering areas such as earthquake and wind engineering. The use of health monitoring system can also provide tools for the validation of structural analytical model. However, only few structures such as historical buildings and some important long bridges have been instrumented with structural monitoring system due to high cost of installation, long and complicated installation of system wires. In this paper, the structural monitoring system based on cheap and wireless monitoring system is investigated. The use of advanced technology of micro-electro-mechanical system(MEMS) and wireless communication can reduce system cost and simplify the installation. Further the application of wireless MEMS system can provide enhanced system functionality and due to low noise densities. Identification results are compared to ones using data measured from traditional accelerometers and results indicate that the system identification using wireless MEMS system estimates system parameters accurately.

• 한국정밀공학회지
• /
• 제18권9호
• /
• pp.71-81
• /
• 2001

This paper analyzes the effectiveness of minimizing vibration and sound transmission on/through a thin rectangular plate by both feedback control and hybrid control which combines adaptive feedforward control with a feedback loop. An experimental system identification technique using the matrix-fractional curve-fitting of the frequency response data is introduced for complex shaped structures. This identification technique reduces the model order o the MIMO(Multi-Input Multi-Output) system which simplifies the practical implementation. The adaptive feedforward control uses a Multiple filtered-x LMS(Least Mean Square) algorithm and the feedback control uses a multivariable digital LQG(Linear Quadratic Gaussian) algorithm. Experimental results show that an effective reduction of sound transmission is achieved by the hybrid control scheme when both vibration and noise measurement signals are incorporated in the controller.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.368.1-368
• /
• 2002

System Identification is carried out for a full scale five-story holing to design a vibration controller design. Dynamic characteristics such as natural frequencies, damping ratios, and modes are obtained from the input/output informal ion by both sine-sweet method and white noise method. The active mass driver installed on the third floor is applied as external loading to move the building and each floor acceleration is measured and processed for the system identification. (omitted)