• Carbon letters
• /
• 제14권4호
• /
• pp.234-242
• /
• 2013

Potassium hydroxide-activated carbons (CK21, CK11, and CK12) were prepared from pistachio nutshells. Physicochemical properties of activated carbons were characterized by TGA, $pH_{pzc}$, Fourier transform infrared spectroscopy, scanning electron microscopy, and $N_2$-adsorption at $-196^{\circ}C$. The examinations showed that activated carbons have high surface area ranging between 695-1218 $m^2/g$, total pore volume ranging between 0.527-0.772 mL/g, and a pore radius around 1.4 nm. The presence of acidic and basic surface C-O groups was confirmed. Batch adsorption experiments were carried out to study the effects of adsorbent dosage, temperature, initial concentration of adsorbate, and contact time on deltamethrin adsorption by activated carbons. The kinetic studies showed that the adsorption data followed a pseudo-second order kinetic model. The Langmuir model showed a maximum adsorption capacity of 162.6 mg/g at $35^{\circ}C$ on CK12. Thermodynamic studies indicated that adsorption was spontaneous and increased with temperature, suggesting an endothermic process.

• Bulletin of the Korean Chemical Society
• /
• 제28권3호
• /
• pp.373-378
• /
• 2007

A micro organism Agrobacterium tumifacient as an immobilized cell on a solid support was presented as a new biosorbent in a simple and sensitive spectrophotometry determination of Ni(II) in various samples using 4-hydroxy benzaldehyde-4-bromophenyl hydrazone as a color developing agent (λmax 497 nm) at pH 4.0 ± 0.2. Beer's law was obeyed over the range of 0.01-0.1 μg L-1. The molar absorptivity and Sandell's sensitivity were 1.285 × 105 L mol-1cm-1 and 0.007245 μg cm-2 respectively. Under these conditions, the preconcentration factor obtained was 82, and the detection limit achieved was 0.05 μg L-1. The detailed study of various interfering ions made the method more sensitive and selective. The recovery of Ni(II) from various samples range from 97.75 to 99.35%. The present method was successfully applied for the determination of Ni(II) in spiked, natural water and alloy samples. The proposed method was compared with reported methods in terms of Student's ‘t'-test and Variance ratio ‘f'-test which indicates that there is no significant difference between proposed and literature method at 95% confidence level.

• 한국안전학회지
• /
• 제21권5호
• /
• pp.17-21
• /
• 2006

In this study, SPCC cross-tension type specimens produced under various spot welding conditions were tensile and fatigue tested. Decrease of 2 kA in normal current condition of 10 kA caused a large amount of reduction in both static joining strength and fatigue life. And 2 kA increase resulted in increase of static joining strength and an increase in low cycle regime but a decrease in high cycle regime, revealing the fact that fatigue strength rather than static joining strength would be a major factor during design process in view of the body endurance. As a results of estimating the fatigue lifetimes of various types of spot weld specimens. equivalent stress intensity factor is the proper parameter for predicting the lifetimes of various types of specimens. which can be expressed as ${\Delta}K_{eq}(N/nm^{1.5})=11550N^{-0.36}_{f}$.

• Transactions on Electrical and Electronic Materials
• /
• 제4권1호
• /
• pp.15-20
• /
• 2003

NiCr alloys are prepared onto poly-Si/ $SiO_2$/Si substrates to replace Pt bottom electrode with a new one for integration of high dielectric constant materials. Alloys deposited at Ni and Cr power of 40 and 40 W showed optimum properties in the composition of N $i_{1.6}$C $r_{1.0}$. The grain size of films increases with increasing deposition temperature. The films deposited at 50$0^{\circ}C$ showed a severe agglomeration due to homogeneous nucleation. The NiCr alloys from the rms roughness and resistivity data showed a thermal stability independent of increasing annealing temperature. The 80 nm thick BST films deposited onto N $i_{1.6}$C $r_{1.0}$/poly-Si showed a dielectric constant of 280 and a dissipation factor of about 5 % at 100 kHz. The leakage current density of as-deposited BST films was about 5$\times$10$^{-7}$ A/$\textrm{cm}^2$ at an applied voltage of 1 V. The NiCr alloys are possible to replace Pt bottom electrode with new one to integrate f3r high dielectric constant materials.terials.

• 한국식품과학회지
• /
• 제29권4호
• /
• pp.630-634
• /
• 1997

N-glycanase처리에 의해 얻어진 1-amino-oligosaccharide를 FMOC-Cl로 표식 하는 방법을 확립하였다. 이 방법에 의해 얻어진 FMOC-표식 oligosaccharides는 기존의 방법보다 약 4배의 감도를 나타내었다. Amido 80 column을 사용한 분석에 의하여, Man 5-9 GlcNAc 2 amines의 5개의 성분은 각각 분리되어 용출 되었으며, 회수율은 기존의 방법과 거의 같았다. 1-amino-oligosaccharides는 0.05 pmol에서 1.5 pmol 사이에서 직선적인 관계를 나타내었으며, 2-aminopyridine에 의한 표식과 비교하였을 때, 안정된 화합물을 형성하고 있으며, 감도가 높아 미량의 oligosaccharides의 분석에 매우 적합한 것이 확인되었다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권6호
• /
• pp.760-767
• /
• 2014

This paper describes a high-radix crossbar switch design with low latency and power dissipation for Network-on-Chip (NoC) applications. The reduction in latency and power is achieved by employing a folded-clos topology, implementing the switch organized as three stages of low-radix switches connected in cascade. In addition, to facilitate the uniform placement of wires among the sub-switch stages, this paper proposes a Mux-Matrix-Mux structure, which implements the first and third switch stages as multiplexer-based crossbars and the second stage as a matrix-type crossbar. The proposed 256-radix, 8-bit crossbar switch designed in a 65nm CMOS has the simulated power dissipation of 1.92-W and worst-case propagation delay of 0.991-ns while operating at 1.2-V supply and 500-MHz frequency. Compared with the state-of-the-art designs in literature, the proposed crossbar switch achieves the best energy-delay-area efficiency of $0.73-fJ/cycle{\cdot}ns{\cdot}{\lambda}^2$.

• 한국재료학회지
• /
• 제19권6호
• /
• pp.313-318
• /
• 2009

Polymer Light Emitting Diodes (PLEDs) with an ITO/PEDOT:PSS/PVK/PFO-poss/LiF/Al structure were prepared on plasma-treated ITO/glass substrates using spin-coating and thermal evaporation methods. The annealing effects of the PFO-poss film when it acts as the emission layer were investigated by using electrical and optical property measurements. The annealing conditions of the PFO-poss emission film were 100 and $200^{\circ}C$ for 1, 2 and 3 hours, respectively. The luminance increased and the turn-on voltage decreased when the annealing temperature and treatment time increased. After examining the Luminance-Voltage (L-V) properties of the PLED, the maximum luminance was found to be 1497 cd/$m^2$ at 11 V for the device when it was annealed at $200^{\circ}C$ for 3 hours. The peak intensity of the PLED emission spectra at approximately 525 nm in wavelength increased when the annealing temperature and time of the PFO-poss film increased. These results suggest that the light emission color shifted from blue to green.

• 한국산업융합학회 논문집
• /
• 제23권4_2호
• /
• pp.693-699
• /
• 2020

355nm UV pulse laser is irradiated on the surface of polyimide (PI) by LDW (Laser Direct Writing) method to produce a high sensitivity flexible humidity sensor using a simple one-step process. The LDW method continuously investigates 2-D CAD data using a galvano scanner and an F-lens. This method is non-contact, so it minimizes physical strain on the PI. Laser-induced graphene (LIG) produced by lasers has a high surface area due to its high flexibility and numerous pores and oxidizers compared to conductors. For this reason, it is highly useful as a flexible humidity sensor. The humidity sensor produced in this study was attached to the inside of a mask filter, which has become a hot topic recently, and its applicability was confirmed.The measurement of humidity measured the sensitivity, reactivity, stability and recovery behavior of the sensor by measuring changes in capacitance and resistance.

• 한국환경과학회지
• /
• 제28권8호
• /
• pp.677-687
• /
• 2019

This study evaluated the biosorption properties of calcium ion using Aerobic Granular Sludge (AGS). A sequencing batch reactor was used to induce the production of Extracellular Polymeric Substances (EPS) through salinity injection, and the calcium ion adsorption efficiency was analyzed by a batch test. The EPS contents showed significant changes (104-136 mg/g MLVSS) at different salinity concentrations. The calcium ion adsorption efficiency was highest for AGS collected at 5.0% salinity, and it was confirmed that the biosorption efficiency of AGS was increased owing to the increase in EPS content. The results of the Freundlich isotherms showed that the ion binding strength (1/n) was 0.3941-0.7242 and the adsorption capacity ($K_f$) was 2.4082-3.3312. The specific surface area and the pore size of the AGS were $586.1m^2/g$ and 0.7547 nm, respectively, which were not significantly different from each other. It was confirmed that the influence of biological properties, such as EPS content, was relatively large among the factors affecting calcium ion adsorption.

• 한국진공학회지
• /
• 제20권1호
• /
• pp.30-34
• /
• 2011

라디오파 반응성 마그네트론 스퍼터링 방법으로 성장된 ITO박막의 열처리에 따른 표면구조, 결정, 전기 및 광학적 특성을 조사하였다. 저온에서 증착한 시료를 챔버에서 $50^{\circ}C$, $100^{\circ}C$, $150^{\circ}C$, $200^{\circ}C$, $250^{\circ}C$로 2시간 동안 열처리하였다. 열처리에 따른 박막의 결정구조, 전기 및 광학적 특성은 X-선회절 장치, 전자주사현미경, 원자현미경, 저항 측정기를 사용하여 조사하였다. 열처리 온도 $150^{\circ}C$에서 450~900 nm 파장의 평균 투과율이 87% 이상 되었으며, 동일 온도 이상에서 ITO박막의 결정이 형성되었고, 저항이 $18{\Omega}cm$로 감소함을 알 수 있었다. 실험결과로 부터 저온 증착된 ITO박막의 전기 및 광학적 특성 향상을 위해서는 적정온도 이상에서의 열처리가 필요하다는 결론을 얻었다.