• Journal of Soil and Groundwater Environment
• /
• v.8 no.2
• /
• pp.19-35
• /
• 2003

In order 새 investigate the spatial and seasonal variations of heavy metal pollution in heavily industrialized urban area, urban roadside sediments were collected for five years from gully pots in Seoul City. A series of studies have been carried out concerning the physicochemical characteristics of the sediments in order to evaluate the contamination of heavy metals such as Cd, Co, Cr, Cu, Ni, Pb and Zn. Roadside sediments and uncontaminated stream sediments were analyzed for total metal concentrations using acid extraction. The roadside sediments are characterized by very high concentrations of Zn (2,665.0$\pm$1,815.0 $\mu\textrm{g}$/g), Cu (445.6$\pm$708.0 $\mu\textrm{g}$/g), Pb (214.3$\pm$147.9 $\mu\textrm{g}$/g) and Cr (182.1$\pm$268.8 $\mu\textrm{g}$/g), indicating an artificial accumulation of these metals to the sediment chemistry. Comparing with average contents of uncontaminated stream sediments, roadside sediments were shown zinc 14 times (up to 64.4), copper 9 times (up to 181.7), lead 6 times (up to 63.7), cobalt 6 times (up to 168.7), nickel 4 times (up to 98.4), cadmium 2 times (up to 12.8) and chrome 2 times (up to 40.2) high content. The relative degree of heavy metal pollution for roadside sediments collected from each district in Seoul City is evaluated using the “geoaccumulation index”. As a result, heavy-metal contamination is highest centering the oldest residential district and industry area, and contamination level decreases as go to outer block of the city. The factor analysis results indicate that the levels of Cu, Ni, Fe and Cr are strongly related to numbers of factories, whereas the concentrations of Cr, Zn and Cd dependant on pollution index, indicating artificial contamination due to site-specific traffic density.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.4
• /
• pp.2940-2944
• /
• 2015

Dredged materials for effective use in Hwasun-port pollution analysis, Ni(nickel) in excess of the standard showed that the whole point. However, according to the revised standards effective utilization exceeds the reference value, even if no anthropogenic sources Pearl ratio less than 10% of the average weight of the ecotoxicological tests have passed, and if so it can be used to beach nourishment. Therefore, the average weight ratio of pearl and ecotoxicological tests were conducted by marine environment official test method. Mud to 5.37% of the average weight ratio lower than the reference value of 10% that was investigated. Ecotoxicity test using bioluminescent bacteria relative luminescence inhibition in the 0 to 9.13% with no toxicity was determined using benthic amphipods in the control and the test sample relative to the average survival rate is 0% with no toxicity was determined. Therefore, the revised effective use meets all the criteria that can be used to beach nourishment, so that the suitability was assessed.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.107-107
• /
• 2018

무전해 니켈도금 용액의 성분은 Ni(II)염, 환원제, 적합한 금속 배위 리간드, 안정제 및 특정 특성 요구에 대한 첨가제를 포함한다. 일반적으로 도금 욕에는 미량의 안정제가 함유되어 있다. 만약 적절한 안정화 시스템이 없는 도금 욕에서 도금 공정 시 도금 시작 직후에 많은 양의 니켈 플레이크(Ni flake)가 생성되어 빠르게 도금 용액이 분해되어 더 이상 도금이 어렵게 된다. 그러나 무전해 도금 욕에서 안정제의 역할 및 도금 층에 미치는 영향에 대한 연구는 여전히 부족한 실정이다. 따라서 본 연구에서는 $Pb^{2+}$ 안정제 농도가 도금 층에 미치는 영향과 캐비테이션 침식 실험을 통해 그 내구성을 평가하고자 하였다. 무전해 니켈코팅을 위한 모재는 회주철(FC250)을 $19.5mm{\times}19.5mm{\times}5mm$의 크기로 가공하였다. 회주철의 인장강도는 $330N/mm^2$이며, 그 성분 조성(wt.%)은 3.23 C, 1.64 Si, 0.84 Mn, 0.016 P, 0.013 S 그리고 나머지는 Fe이다. 시험편은 SiC 페이퍼 #1200까지 연마하여 시험편의 표면 거칠기는 $1.6-2.1{\mu}m$ 범위 내로 제작하였다. 무전해 도금 전 시험편은 탈지를 위해 상온의 아세톤 용액에서 3분간 초음파 세척하고, $90^{\circ}C$의 알카리 수용액으로 5분간 세척하였다. 그리고 표면 활성화를 위한 산세척은 5% 황산용액에서 30초 동안 실시하였다. 도금조로 500mL 비커를 사용하였으며, 모든 시험편은 2시간 동안 무전해 니켈도금을 실시하였다. 그리고 니켈도금 층의 내식성과 내구성을 평가하기 위해 전기화학적 분극 실험을 통한 타펠분석과 ASTM G32 규정에 의거한 캐비테이션 침식 실험을 실시하였다. 그 결과 안정제 농도가 도금 속도와 도금 층의 성분 변화에 크게 영향을 미쳤으며, 그에 따라 도금 층의 내식성과 내구성이 크게 변화되었다.

• Restorative Dentistry and Endodontics
• /
• v.24 no.4
• /
• pp.633-638
• /
• 1999

The purpose of our study is to evaluate the ability of nickel-titanium(NiTi) files in maintaining the original curvature of a curved root canal during canal preparation. Curved canals on translucent resin blocks were prepared with Profiles and stainless steel files and they were placed at the platform which can reproduce the same position. The unprepared and prepared canal forms were accurately compared by double exposure technique of photography. The results were as follows : 1 NiTi files made a canal comparatively taper, but stainless steel files didn't make a canal taper, wicest at midportion and comparatively wide at a apical portion. 2. Canals preparations with no. 25 Profile.06 up to the working length were most excellent in taperness and in maintaining the original curvature. Canals prepared with no 30 Profile.06 up to the working length made a little outer transportation at a apical portion, but not severe. 3. Canal preparations with Profile GT were excellent in taperness and in maintaining the original curvature, but made more enlargement toward the inner side at the starting portion of the curvature. 4. Canal preparations with stainless steel files were not tapered and provided the largest transportation.

• The Journal of Korean Academy of Prosthodontics
• /
• v.40 no.6
• /
• pp.590-596
• /
• 2002

The resin : metal interface is at the basis of most bonding failures in resin-bonded prosthesis. Although debonding has been a problem with adhesive fixed partial dentures, various dentists classify them as long-term restorations. The advantages of resin-bonded fixed partial dentures include minimal tooth reduction and the possibility of rebonding. if resin-bonded protheses can be easily rebounded, it is of clinical importance to know if the lutingagents rebond as well the second time as they did originally. Several retentive systems for resin-to-metal bonding have recommended. Treatments such as electrolytic etching and silicone coating, despite the good result of bond strength, have proved to be time-consuming and technique-sensitive. Therefore a simple and more reliable method is desirable. This study evaluated the effect of metal surface treatments on the rebond strength of panavia 21 cement to a nickel-chromium(Ni-Cr) alloy. The samples were received the following surface treatments : Group No.1 (control or served as the control) treatment with sandblasting with 50um aluminum oxide and ultrasonically cleaned for 10minutes in double-deionized water, Group No.2 were no surface treatments. Group No.3 were treated with metal primer. Group No.4 were treated with sandblasting as previously described, and then metal priming. From the analysis of the results, the following conclusions were drawn. 1. Sandblasting and metal priming appears to be an effective method for treatment of metal after accidental debonding. 2. Group without surface treatment had significantly lower bond strengths compared with other groups. 3. The combination of sandblasting and metal priming may not develop superior bonding strengths compared with other techniques that used the Ni-Cr alloys. 4. Combination of cohesive and adhesive failures were the most common type observed. The results support the use of sandblasting as a viable procedure when rebonding accidentally lost adhesive partial denture. We concluded that sandblasting and metal priming of metal surface before bonding could provide the adequate bond strength during rebonding of resin-bonded fixed partial denture.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05a
• /
• pp.34-37
• /
• 2003

본 연구는 고온초전도 coated coductors의 기판으로 cube texture된 순수 Ni 기판을 개발하기 위하여 전체 가공율과 압연율에 따른 (100) texture의 변화와 1차적으로 열처리한 기판을 다시 압연한 후 재열처리 하였을 때의 전체 가공율과 압연율에 따른 (100) texture의 변화를 GADS XRD와 SEM을 이용하여 연구하고자 하였다. 그 결과, 압연 후에는 압연율에 관계없이 비교적 약한 강도의 (220)과 (200), (111), (311) peak가 나타났는데, 4%로 압연했을 경우 (220) peak가 가장 강한 peak로 나타난 반면, 10%로 압연한 경우에는 (200) peak가 비교적 강하게 나타났다. 그러나 이를 $900^{\circ}C$에서 열처리한 후에는 (200) peak 만 뚜렷이 발달되어 나타났는데, 전체 가공율과 압연율이 높을수록 (200) peak의 강도가 높게 나타나 압연을 통하여 발달한 결정립자의 (110) 면을 따른 배열이 열처리 과정을 통하여 회전하여 (100)면을 따른 배열로 바뀌는 것으로 추측할 수 있었다. 그러나 $900^{\circ}C$에서 열처리한 두께 0.2mm 판재를 다시 0.1mm까지 4%와 10%의 압연율로 압연하고 500~$900^{\circ}C$에서 1시간동안 최종 열처리한 후에는 상대적으로 낮은 2차 가공율에 의하여 집합조직의 전체 가공율과 압연율에의 의존성이 사라지는 것으로 나타났다.

• The Korean Journal of Ecology
• /
• v.11 no.1
• /
• pp.29-36
• /
• 1988

This present study has been carried out to examine the correlation between the distribution of the coliform bacterial plasmids and the viability test against heavy metals in the upper stream of Han river(Gapyung; clean water) and the its basin (Anyang Cheon; polluted water). And the distribution of plasmids were examined to be used as trophic indicator for analysis between the clean and polluted waters. 1. A total of 110 isolates were analyzed for the presence of plasmids by means of the boiling method and agarose gel techniques. Plasmids were significantly more frequent in the strains which had been isolated from the clean water (14.3%). Also, there were much higher multiplicity of plasmids at the polluted water(41.0%), compared with the clean water (33.0%). By the comparision between molecular weight of bacterial plasmids in the clean water and those of polluted water, there were no significant differences of the clean water from the polluted water, to such extent as 30.0%, 28.6%, respectively, in frequency for occurrence of high molecular weight plasmids iver 35.8% Mdal. 2. Each isolate was carried out the resistance test for mercury(10-5M), nickel(10-3M) and arsenic (0.1%). At the polluted site, the survival ability of the plasmid-carrying straings(Hg, 31.0%l Ni, 5.7%; As, 65.7%) was higher than that of the non plasmid-carrying strains(Hg, 12.1%; Ni, 3.0%; As, 54.6%). This trend was more remarkable in the clean site (plasmid-carrying strains: 16.7%,-,-). As a result it is suggested that plasmids could be used as an indicator of a certain types of water pollution. In addition, heavy metals might have inflyenced, some extent, to the distribution of plasmids in the environment which has been surveyed in the present study.

• Journal of Soil and Groundwater Environment
• /
• v.19 no.1
• /
• pp.1-7
• /
• 2014

When processing the biomass by Hydrothermal carbonization (HTC), a slow pyrolysis process, it produces bio-gas, biooil, and biochar. Among these end products, biochar is known for isolating or storing carbon and being used as a soil amendment. In this study, the characteristics of biochar generated by HTC at $250^{\circ}C$ for 1 hour, 2 hours, 3 hours, and 20 hours with synthetic food wastes and wood wastes were analyzed for potential uses in soil contaminated with heavy metals. The yield of biochar (weight %) increased when the ratio of wood wastes increased and showed a decreasing tendency as reaction time increased. Elemental analysis of biochar based on various conditions showed a maximum of 70% carbon (C) content. The carbon content showed an increasing tendency with the increase of wood wastes. Iodine adsorption test was peformed to determine the optimum reaction condition, which was 15% wood waste for mixing ratio and 2 hours for reaction time. Using biochar generated at the optimum condition, its capability of adsorbing heavy metals (Cd, Cu, Pb, Zn, Ni) was evaluated. It was concluded that lead (Pb) was removed efficiently while zinc (Zn) and nickel (Ni) were hardly adsorbed by biochar.

• Applied Chemistry for Engineering
• /
• v.19 no.3
• /
• pp.304-309
• /
• 2008

Cryptand series ion exchange resins were synthesized with 1-aza-12-crown-4 macrocyclic ligand attached to styrene (4 series dangerous matter) divinylbenzene (DVB) copolymer with crosslink of 1％, 2％, 4％ and 8％ by a substitution reaction. The synthesis of these resins was confirmed by content of chlorine, element analysis, electron micrograph, and IR-spectrum. The effects of pH, time, dielectric constant of solvent and crosslink on adsorption of uranium (${UO_2}^{2+}$) ion were investigated. The uranium ion showed a fast adsorption on the resins above pH 3. The optimum equilibrium time for adsorption of metallic ions was about two hours. The adsorption selectivity determined in ethanol was in increasing order uranium (${UO_2}^{2+}$) > nickel ($Ni^{2+}$) > gadolinium ($Gd^{3+}$) ion. The adsorption was in order of 1％, 2％, 4％, and 8％ crosslinked resin and adsorption of resin decreased in proportion to order of dielectric constant of solvents.

• Journal of the Korean Solar Energy Society
• /
• v.33 no.3
• /
• pp.42-50
• /
• 2013

Solar thermal reactor was studied for hydrogen production with a two step thermochemical cycle including T-R(Thermal Reduction) step and W-D(Water Decomposition) step. NiFe2O4 and Fe3O4 supported by monoclinic ZrO2 were used as a catalyst device and Ni powder was used for decreasing the T-R step reaction temperature. Maintaining a temperature level of about $1100^{\circ}C$ and $1400^{\circ}C$, for 2-step thermochemical reaction, is important for obtaining maximum performance of hydrogen production. The controller was designed for adjusting high temperature solar thermal energy heating the foam-device coated with nickel- ferrite powder. A Pill temperature control system was designed based on 2-step thermochemical reaction experiment data(measured concentrated solar radiation and the temperature of foam device during experiment). The cycle repeated 5 times, ferrite conversion rate are 4.49~29.97% and hydrogen production rate is 0.19~1.54mmol/g-ferrite. A temperature controller was designed for increasing the number of reaction cycles related with the amount of produced hydrogen.